05-2011 Nissan frontier and pathfinder engine installation

[@nightcoder5k]

Amazing job man. You made it look simple, but I know it's not that easy.

[@c-yabugginout7573]

Watched the first one but just saw this install video...great job once again. I am about to remove the old motor before I call it a night. Stopped to eat and saw this. Thanks again for sharing. We need more good folks helping others like your doing!!

[@alltsab]

You welcome. like, share, and help subscribe brother

[@beactivelife]

Thanks for sharing the video of removal and installation of the vq40 engine. I am sure it will help a lot of others.

[@stephengordon8968]

I'm doing my 07 pathfinder and this helped alot even if it wasn't exactly the same thing . Thank You very much !

[@alltsab]

Unwelcome

[@BuhdFrankDaTank93]

Thanks for your videos , gave me the confidence to remove and install a new motor for mine ! All I have to say is watch out with the heat shield bolts on the exhaust mani and some of those bell housing bolts are a PITA !

[@alltsab]

Glad you got it done

[@RustyRecovery]

Great video. You made a whole lot of work look very simple. That new motor certainly sounds a lot better than the busted one you took out. Thanks for sharing.

[@frankserrano537]

HO boy you are pretty GOOD MECHANIC MAN , congratulation.

[@alltsab]

Thanks

[@gilbertoayala-fortnite1000]

Hay que cambiar la computadora si se cambia el motor

[@HarrellB_US]

Today's the day. I've got my new engine. Question. Exactly where did you hook you're chains at on the engine to lift it? Is those 3 or 4 skinny bolts sticking out where the exhaust goes? Can't find anything on google

[@alltsab]

Exhausted bolt is good

[@HarrellB_US]

Roger that. Do you have an email address i can email that way if i run i to a snag you could maybe help out?

[@HarrellB_US]

@@alltsab oh and you said exhaust bolt was fine but is that how you did it?

[@alltsab]

@@HarrellB_US no email.. yes exhausted bolt unless some engine have engine hook

[@fvg3401]

what other small trucks that a 4.0 frontier engine can be installed in?

[@dennisreed3813]

have a 06 pathfinder over heats, new water pump-thermostat, can't get all the air out of water system. now cuts out @ 2000 rpm's idols great for hours but cant go two doors down street without blowing water out, any solution?

[@alltsab]

I read your question but still not understand 💯 percent. I will try to answer your question. Air in the system may not cause like that. If you idle the to the normal temperature and shut off and later when it cool down you can top off water to the radiator to get fully water in your engine and radiator that should help out with air in the system. I'm lost about 2000rpm part but if your rmp doesn't go lower than 2000 rpm then try to taping the top of the body throttle with small hammer to see it drop. Hope I answered your questions. Thanks for watching and don't forget to help me subscribe to support my channel. Thanks

[@NatachaGuyanemuagkhoom]

😦💪💪💪👍👍

[@alltsab]

Thank you for the support.

[@erickugarte213]

We're are u located I have the same truck I need u to change the motor

[@alltsab]

I'm getting old can't do it anymore.

[@matthewlentz6008]

I have an 07 extera sport 6 speed manual and I can"t pay anyone around to do this for me. I have the money but not the knowledge and no motor. I really don't want this beast to rot in an auction yard. I'v grown fond of it.

[@HarrellB_US]

Hey if you can get back to me I appreciate it cuz I've heard different pounds for this flywheel those 6 bolts that are on that Nissan says 65 lb and Nissan forums are saying 110 220 lb so what did you tighten that flywheel bolts too sir. Thanks again

[@alltsab]

Look for my nissan pathfinder clutch installed i have it. I remember I did used only 65 lbs but check my video for sure ok Buddy 👍

[@alltsab]

Just go according to the book ok

[@HarrellB_US]

Did you install the converter on the engine before installing the engine

[@alltsab]

@@HarrellB_US my is not authentic so I install the clutch before instal. If you authentic then your torque converter should be inside your transmission before instal the engine.

[@HarrellB_US]

Rodger that but thank you so much for your uploads I've been watching it religiously while I took out the engine and you make it look so easy because if you put in all the little things you have to do it would have been a 16 hour video LOL