1:11

[@fredmitchel1236]

I am glad you are showing lots of detail...I have a 2017 KTM 300....and now I know what my engine looks like

[@UpAllNight91]

Yes, the 300 is the same motor, just a bigger cylinder bore and piston

[@joelatkinson2080]

Another great video!!!

[@UpAllNight91]

Thanks! This was surely one of my earlier videos.

[@fredmitchel1236]

Nice the way the crank nut was retightened... Good job

[@PerformanceUnlmtd]

When you install bearings and are tapping them in never hit the inside race @ 37:31...the outer race should take all the force for installing any bearing to prevent embrittlement of the inner race as well as there should be support under the case as well. You should also heat the case and the bearing will fall easily into the case and seat correctly, because installing a bearing in a cold case by force also distorts the opening .....otherwise nice build.

[@garyalexander2480]

That was painful to watch found it odd he had the torch and obviously has a larger socket just heat it up otherwise not bad vid

[@fredmitchel1236]

I couldn't of said it better .

[@fredmitchel1236]

I had this KD stud remover tool to remove locating pins...used on the VM since 1977

[@livefreeandshred9818]

I'm subscriber 432. Videos are very informative. Keep doing what you're doing

[@UpAllNight91]

Thanks and thanks for watching!

[@fredmitchel1236]

I am glad my engine is filled with shims instead of washers

[@keithalexander36]

Earthquake impact puttin in the work yo.

[@rwcasto]

Nice man- i had no idea they made kits like that

[@UpAllNight91]

Yeah I didnt either . Going to be interesting to hear how she sounds and feels

[@fredmitchel1236]

Wow.. It looks like the crank is filled with nylon....?

[@peaceprayer595]

You seem like such a quality dude and obviously a knowledgable mechanic, Can you please ditch the carpenters hammer for a ball peen or dead blow? Carpenter hammers are made of lower grade steel and are more likely to spit pieces. If you really have to bang hard on something. you're more likely to get a sliver of steel in the face or eye. Other than that, I can't wait to build one of bad boys some day. Thanks for the help.

[@UpAllNight91]

Thanks. Yes. I agree I need better hammers and stuff. I will be shopping around some good ones. Thanks for commenting and Thanks for watching!

[@peaceprayer595]

@@UpAllNight91 Ball peens are dirt cheap at Harbor Freight and you'll get different sizes in the packade. They work superlative!

[@UpAllNight91]

@@peaceprayer595 thanks. I will grab some of them on my next run to harbor!

[@peaceprayer595]

@@UpAllNight91 thank you for responding! Hope you love them.

[@UpAllNight91]

@@peaceprayer595 Right on!

[@fredmitchel1236]

Occh....nice job on the bearing beadings brutality....lol

[@fredmitchel1236]

Maybe when you get the 500 cc BRC engine running...try changing the oil more often

[@UpAllNight91]

That bike is in the owners hands now. I think he owns like 2 of these now

[@fredmitchel1236]

Cool and good job for converting to a power house

[@fredmitchel1236]

Isn't nice to use the impact tool...and to remove all the bolts...while leaving the last one all tight holding all that that force. So then it get stressed

[@fredmitchel1236]

The new KTM uses the power valve clip...my 1998 380 uses that clip... I now like referring it as new... Lol

[@randylangguth7926]

Think you need to make a roast chicken before your next video. 👍great video but the rooster……😂

[@UpAllNight91]

🤣🤣🤣

[@fredmitchel1236]

Using heat on a threaded bolt nut or stud assembled with red Loctite...will become loose and finger tight

[@patrickb.mxer2184]

Nice!!

[@tucanman9775]

what about A RC 390 frame does it make 60hp 50t

[@nandog1024]

I never look instalete the bearing in center crash¡!!!

[@oleorm6940]

Can the gearbox take the torq.

[@UpAllNight91]

So far it has but I was thinking the same thing. Even a 450 has a beefier transmission thans a 250 smoker.

[@richardhorn9539]

Watching those bearings get installed was Horrifying

[@UpAllNight91]

Been doing this for years. Have over maybe 3000 motors under my belt. Thanks for watching!

[@richardhorn9539]

@@UpAllNight91

[@richardhorn9539]

Doing it over and over doesn't make it right and you were wrong doing it wrong.

[@UpAllNight91]

I've done them all the different ways, a frozen bearing on a warm case is a no Brainer. With good coordination its easy fast and works every time.

[@riharddanielsson207]

Can People buy this

[@UpAllNight91]

I believe so. If you Google 500cc BRC racing you will find thier site. I think it's around 6k or so give or take depending on the options you choose like E start or kick start

[@Ronhickmott]

A 12v cordless impact driver is best for the bike bolt sizes, mine has a nice slow startup, way less cross threading.

[@UpAllNight91]

Nice

[@gregnowak6450]

Less or no?

[@Ronhickmott]

@@gregnowak6450 none with care