1.5 Mazda 2 Throttle Body DIAGNOSIS , Removal , Clean , Replacement ts2

Playlist with more Videos about this car • 1.5 Mazda 2 Mass Air F...
How to clean and diagnose the Throttle body on this Mazda 2 with a 1.5 liters gasoline engine TS2 . It can be challenging to find out what is wrong with your throttle body without having a scan tool with live data . So in this video you will see how to diagnose and clean the throttle body .
Disclaimer :
This youtube channel: "doit_vehicles " can not guarantee that this information suits your car . "doit_vehicles " assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk.

[@doit_vehicles]

Coolant Change : kzbin.info/www/bejne/l2LZgX9jaqafjdk

[@THC800]

My car's idle was very rough and I couldn't figure out why until I watched this video and saw your throttle body. My throttle body was super dirty and I decided to clean it. Behold! No rough idle, no vibrations, and as a bonus my check engine light turned off. Thanks for this video!

[@doit_vehicles]

I am glad to hear that !

[@leorodriguez9863]

Great video. I been watching watching your work and they're fantastic. Thank you. Huge help for me! Mazda 2 owner since 2015.

[@nirmosko]

thank you for the video! is it the same on mazda 2 2009?

[@michaelmooney1474]

Lifesaver !!!!!!!! In my neck of the woods. Indiana US. Not much info on these cars. THANKS

[@darwo1293]

i've cleaned mine and now the engine have more power and is more stable at idle, but when pressing the brake pedal now I have to press strongly than before, shoud i change the brake pads? or maybe reset something? i noticed that when braking the engine keeps running at 2k rpm until stop, is it normal? thank you good sir

[@michaelbince9670]

Awesome please upload more about mazda 2

[@jasonl3185]

Have you done the pvc valve replacement on this car???

[@HelalMiah-bi4bj]

Hi I have a Mazda 2 2011 1.3 engine MZR. Where is the PCV valve on the car? Thanks

[@skurys]

My idle isn't rough but it sometimes feels like it hesitates in the lower gears/rpm, like going slow in 2nd and the car feels jerky even tho im not doing anything different on the pedal. Not sure of this might help for that

[@janaroderova3203]

Hey mate, any idea what could cause a rough intake noise and loss of power with the engine under load? happens around 3-4k revs. cheers!

[@vig_Indomitable]

Bro I have a 2008 mazda 2 ts, I feel my gas pedal is too sensitive any suggestions ?

[@emily_xox4568]

I have the same car, did you find a solution

[@gyorgs]

Good day Sir. My M2 throttle body make some buzzing sound after the cleaning. If you position the key in "on position", is the sound normal?

[@doit_vehicles]

yes , most of the will do that

[@edgarvasquez9960]

Buen día como cambiar los dos patines de la correa de accesorios del mazda 2 modelo 2010

[@ismailfaruqi543]

Hello sir, Great video from you again.. I want to ask you about torque for Throttle Body and EGR Valve.. What is the best torque for TB and EGR in Mazda2 (2009 - 2014) ? Thx a lot

[@carbonneaud3]

On google I found that : Assemble the throttle body with the 2 bolts and the 2 nuts. Torque the bolts and nuts to 14-18 ft. lbs (19-25 Nm). Did you found the same thing ?

[@zlatkoschauer5744]

Dear please for advice, mercedes w169 a170 petrol, when it's cold it turns on and works on 3 cylinders, and when it heats up it works normally and shows p0304, I replaced the spark plug, cable and coil and there was no change

[@doit_vehicles]

the best is to do some tests before replacing anything : injector test , compression test , connections etc

[@Chr079]

Where are you based at the moment ?

[@darwinb718]

torque for the 10mm bolt of the throttle body? thanks

[@carbonneaud3]

On google I found that : Assemble the throttle body with the 2 bolts and the 2 nuts. Torque the bolts and nuts to 14-18 ft. lbs (19-25 Nm). Did you found the same thing ?

[@theriver8524]

Another great video that is going to help me do a big service on my car! Do you think it would be wise to do a Prestone cooling system cleaner flush on my car? It is time for me to change my coolant fluid, but the Mazda2 takes a special type of fluid and I am nervous that the Prestone flush might cause harm. However I think it would be good to do it too to help keep clean the system before I add in the new coolant. I appreciate your help with this! Do you have a venmo or something where you can take $ for supporting your channel and its helpful videos?

[@doit_vehicles]

It shouldn't do any damage if you run that flush fluid for a short distance . To have the peace of mind you can flush it a second time with destilled water before replacing it with the final coolant

[@moox1412]

where did you buy the headlights?

[@David-zx8fc]

These are official Mazda 2 headlights. I have the same on my 2012 Mazda 2 1.5 MZR, my car was originally built with them.

[@axenz1]

Mass air flow cleaner got Expired date? OMG I need to check my 3syears stock... thanks for the info.

[@otengdarkwa3955]

I replaced my AC compressor and after that,anytime i turn on my Air conditioning,my engine stop in idle.when I’m in traffic with AC on,the engine stall..I adjusted(increase) the rpm and everything is okay now but my car move a lil bit without accelerator pedal..any idea of what to do ?

[@carbonneaud3]

is it not normal that your car moves a little bit without accelerator pedal ? Obviously when not in neutral... right ?

[@carbonneaud3]

Like many parts of your vehicle, the air conditioning system takes its power from the engine. It’s understandable that due to this, there may be significant pressure on the engine. If not controlled, it can lead to overload or malfunctioning. An example of this is regulating the idling rotational speed through the IAC (idle air control) valve. Also referred to as the idle air sensor control motor, due to its function. The valve determines the amount of air that bypasses the throttle plate in a fuel injection IC vehicle, therefore changing the idling speed as necessary. A fault in the IAC such as build up, can cause poor idling or stalling of the engine. If not working properly, the engine may not cope with the loads produced by various systems in the car. More specifically, it may be too low to run the A/C and hence it stalls when turned on.

[@carbonneaud3]

While the IAC valve is a common cause of the problem, there may be other reasons afoot. The A/C system usually requires a lot of generating power and if not supported fully, it may not function properly. This could be due to other components running inefficiently, such as a seized compressor which can no longer turn. This could lead to debris being sent through the A/C system and severe damage to the compressor and other related parts.

[@ayhanmutlu5722]

Thank you

[@janetchoy52]

Using M3 HEADLIGHTS?

[@eliranef]

❤

[@diminisher507]

One billion km