#10 HOW TO Connect the three phases CEE plug

[@imrancrystal2425]

I have a 4 pin plug on the forklift charger and need to change it to the 5 as my socket has 5 holes however there are only 4 wires coming out our the charger, Black, Brown, Grey, Yellow/Green. How can I wire this into a 5 pin plug?

[@plasticsman10]

Hi. Can i wire a standard uk plug to one of these 5 pin sockets? Just Live, Neutral & Earth. If so how do i do it? Thanks in advance.

[@melvinpaul9302]

where can one find an adapter from a three phase European generator 5 plug 230v to a USA type 4 plug at 220v

[@leozhao175]

Does it miss labeled L1 and L3? Shouldn’t L1 and N next to earth?

[@battipav]

Hello Lei, for any technical request please write to [e-mail], thank you!

[@MrM4Goo]

Why make the effort to even reply to the many comments on here if you wont even answer the simple questions asked ?

[@battipav]

@@MrM4Goo we only do as filter for our commercial and technical departments. All the info needed should pass through [e-mail] in order to receive detailed and proper replies. Thank you for understanding!

[@pablopolski1228]

agree, my EU three phase has L1 and N next to earth. I was totally confused watching this video

[@temp06j723-pmeighttq]

L¹ & N is the same position as its Single ∅ CEE commando Plug counterparts. For Plugs, looking from the terminal wiring side, with PE prong downwards, L¹ on Left ,while N is on Right. L² & L³ will rotate Sequentially After L¹ Until it Reaches N.

[@meowsoftware7258]

Can I use 5pin plug for single phase ?, problem is in my local area its only 32a plug available, but my generator is 40a 220v single-phase PE pin for PE L1 and L2 for Live L3 and N for Neutral

[@temp06j723-pmeighttq]

No, you wouldn't do that. If your CEE Socket & Plug are 5prong but you are utilising 1 ∅ only, then: PE prong for Earthing wire N prong for Neutral wire EITHER L¹, L² or L³ (choose any one) for your Line(live) wire .

[@eugeneeugene3313]

Use the ferrule with the flexible (multiwire core) cables!!!

[@matthewh5141]

What about when the plug has a pilot pin? What is it used for an if not needed can you leave the terminal blank?

[@battipav]

Dear Mr. Higgins, Thank you for your message! Please send all your enquiries to the email address: [e-mail] We will be glad to assist you! Battipav

[@alttee4321]

Pilot pin is used on some supplies to engage a contactor that then switches the power on. Useful for motors so you do not connect whilst live.

[@aletcantasi]

Pilot contact is available in 63A and 125A plugs and sockets. Kind regards...

[@zargham086]

I have only black blue and brown wires How can i connect that?

[@hvravi1952]

Knowledgeable vedio.

[@flecksrandomstuff4593]

And you don't connect stranded cables like that... you use ferrules or soldering iron!!

[@alttee4321]

Ferrules are a legal requirement in UK on stranded fine cable, soldering is not allowed as creates a weak joint that WILL fail. This assembly method fails a PAT test :)

[@tadeuszmagoska2537]

A gdzie tulejki kablowe?

[@homeztory7547]

What is cable name and spec?

[@battipav]

Thank you for your interest! Please forward all your request to the email address: [e-mail] We will be pleased to assist you!

[@MrM4Goo]

He already asked you once why would the OP want to send another message to ask the same question again

[@dawoodqaderi87]

Grazie per condividere

[@Marginal391]

Thank you 👍🙃

[@Soho9111]

I love KZbin

[@gamo98]

that plug is eouropean plug not Australian plug

[@battipav]

Dear +gamo98, for any question or enquiry, we kindly beg you to send an email to: [e-mail] We will be glad to assist you! Best Regards

[@MrPontus]

good video, but the "wrong plug"(316-6) can sometimes be the right one, yesterday I replaced an old illegal outlet (Semko 17) with a 316-6 because the cable just have 4 conductors (3P+E). I know some cheat and install a 416-6 outlet without a Neutral but I would never do it

[@battipav]

Dear Mr. Pontus, Thank you for your message! Our machines are designed to be connected to 5 pins cables . Other kind of power supplies, not provided for by the manufacturer and not indicated in the instruction and maintenance manual are not allowed, failing which the warranty void. Best Regards BATTIPAV

[@MrPontus]

sorry, I missed the part that you make machines. yes you are right, I'm limited to use old machines or machines that don't use Neutral

[@christophergeorge38]

Battipav

[@evertsmid560]

i have 2 black wires and no white one

[@battipav]

Dear Evert, the important thing is to connect the yellow/green wire to the ground and the blue wire to neutral one. The other wires can be of different colors and connected in the preferred sequence. Best Regards

[@asnaahmad4863]

Ok thanks sir

[@asnaahmad4863]

I have 3 black and 1 yellow sir

[@battipav]

If you need assistance, please send an email at [e-mail] we will be glad to assist you!

[@lesburrow8700]

the 3 black shoud be numbered. L1 = 1, L2 = 2, L3 = 3, (L4 = N), E = E

[@guddukumaryadav4578]

Thank sie

[@dibyaranjannayak8353]

Hii sir

[@elektroqtus]

Wrong side of the world. If I were back in Germany, this would have been useful.

[@battipav]

Hello! where are you from? Please fill this form and we'll try to help you at the best: battipav.com/en/contacts/