10 Life Hacks with PVC #30

[@TBryan226]

3 Game changing bending techniques better than heat gun. WARNING: CAN BE DANGEROUS!! MUST EXERCISE CAUTION!! If not applied correctly heat guns can cause crimps due to uneven or insufficient heat. These methods heat more evenly than a heat gun and primarily from the inside out allowing for (in my opinion) a better result. 1. Boiling hot water (best for larger diameter pipe used on projects such as roof bows). Without glue,cap one end, (for optimal results make a jig out of a sheet of plywood, wide board or old table). Fit into jig. Attach a connector, short piece, 90 and another short piece with a funnel (essentially a filler tube) and fill (heavy rubber gloves advised) with boiling water. Wait a few minutes and flip jig to drain, run cold water through to cool. Remove from jig. Makes a uniform bend in multiple pieces. 2. Hot sand (best for narrower diameters such as 1" and smaller). Securely duct tape one end of pipe. In an old pan heat pre measured amount of sand. Using gloves funnel sand into pipe until full and tape off. Allow a several minutes to heat thoroughly. Remove tape, dump sand and shape as desired. Great for coiling, looping, etc. 3. Tail pipe (not preferred method, but does work well -- GLOVES ARE A MUST!) If applicable, have buddy hold beer and advise "Watch this!" (LOL). Insert PVC pipe into tail pipe. Run engine for about five minutes. Remove PVC pipe and bend (it comes out like spaghetti). I hope these help to open up new project possibilities, but above all please exercise equal parts caution, common sense and care!

[@TealCheetah]

thumbs up for sharing the wheel chair motorcycle one

[@shaidynd]

The wheelchair idea n the door closer for the older women are the best in my opinion because it creative ideas on how we can help those disabled or in need of adaptive on a budget creations you should make a series just on this. Me n so many more would follow.

[@JohnMiller-oz7gv]

The wheelchair rocks.

[@SOLIZ49erFAITHFUL]

I love the ideas....especially the fencing decor. I have been trying to decorate the yard a bit with simple inexpensive materials. If I ever get a chance to make the fencing project , I hope to take a few pictures and forward them for all to see. Thanks

[@georgekabacinski]

Num 7, what about using wing nuts that could easily be tightened to hold the fan at any given angle?

[@thelegsmanterry]

I like the fan stand.

[@AbdulAwwalQuranwala]

Great video Super duper

[@JG24AJ]

LOVE IT, thanks for sharing.

[@phunkissartisticcreations2316]

Another batch of great uses for PVC. We loved the cable tie/pencil holder especially!

[@SpecificLove7]

Thank you, it is out favorite too.

[@Hicaliber1]

The fan mount was a great idea

[@twincities69]

Always enjoy watching your videos. They really inspire my creativity. Thank you!!!

[@SpecificLove7]

Thank you

[@nagaraj-ck2ej]

Loved the hanger one. Good one👍🙏

[@rebeccamiller3248]

Loved all of them another thing about fan stand it can also be mounted on a wall fantastic idea.

[@michellemann5103]

Another suggestion for your door cane is add a small rubber end to the 90 bend to press gate intercom buttons

[@jiloawad6778]

U R not only amazing U R brilliant

[@danielaguirre5210]

Where can I find clear PVC? I can’t seem to find it at my Local Lowe’s or Home Depot. I’m I looking in the wrong place?

[@albertwells8393]

You should do videos with black plumbing pipe too.

[@jjo5375]

Always a happy, informative time watching your videos! Thanks! : )

[@SpecificLove7]

Thank you

[@sanjayMpatil-wh9yo]

Plz maka a PVC bicycle 👍👍👌👌

[@guyh.4553]

For the fan hack, use carriage bolts. The square end fits perfectly in the holes for the bolts...

[@povmonyneathmorm3320]

Please show also how to make it. Thanks

[@luayalqaisi3438]

Great.. thank you

[@adolfoperezz]

Number 7 got me to subscribe. Super rad!!

[@stephaniemalley9018]

Very awesome video including idea of wheelchairs 😄

[@ensignj3242]

Where did you find clear PVC?

[@TheLightHouseLady]

Great Idea's

[@SpecificLove7]

Thank you

[@lightsobrite]

I need your advice. I am working on a project where I am actually making a window cat perch out of three-quarter inch PVC pipe now to mimic of the one that was purchased years ago that is broken and cannot any longer be repaired from watching several VR videos I actually need some snap tabs either a 24-inch snap tab that will fit the three-quarter inch PVC so that I can mount that to the windowsill and hold the frame or several three quarter inch by 3 inch individual snap tabs might do the same thing if those snap tabs aren't available for three-quarter inch PVC pipe what do you suggest as a substitute? I cannot find any such snap tabs for three-quarter inch PVC and I really don't want to invest the money in one inch PVC pipe as I've already got all the dimensions cut and fitted together. Also I need some snap crosses that also fit the three quarter inch PVC pipe and what would you suggest for a substitute for that if the three-quarter inch are not available? Looking forward to your reply thank you so much for posting all these videos I really enjoy stuff made out of PVC don't ask me why I just do.

[@SpecificLove7]

Thank you so much for the question, but I do not know for sure. Check their website for sizes.

[@thebeliever1753]

How many videos do you have with the pvc title? Can you make a chair or a throne for drums? by the way im a new subscriber.

[@floydaltonmiller]

I love your PVC videos, I need a cover for a pontoon boat that is 7 x 17. What would you build?

[@kaycox5555]

Terrific ideas!

[@docink6175]

My first thought with the fence model was pan pipes you know multi flute... LOL... We built fences like that when we had the haunted house, sometimes just drilling right through larger PVC pipe. Wheelchair motorcycle dealio was awesome and the fan stand is going to be have a few cousins around my place

[@SpecificLove7]

I picked up the fence idea from Halloween decorations, lol. Glad you can use the fan stand.

[@joseelcurioso5215]

Good video

[@floydaltonmiller]

Another great video.

[@AgilizeSuaVida]

Very Nice man.

[@bluesroc]

where do you get pvc at

[@SpecificLove7]

I picked it up from a local warehouse. You should be able to find it online.

[@SpecificLove7]

I added some on my AMAZON Influencer Page: www.amazon.com/shop/influencer-6a30516b

[@nickkk420]

±1 for the fan stand btw

[@LocalScenery]

♥ ♥ ♥

[@theresevanderwalker6932]

I did some plumbing with pvc

[@pedrovelazquez9755]

Want to make a rack for a baleno car

[@Pacman0820]

U didn't use my idea thanks man really

[@SpecificLove7]

I still plan to use it, I just have others listed before it.

[@exploayuda]

te falto hacer un instrumento musical

[@bluesroc]

clear pvc at

[@brucecampbellforpresident1393]

I want to make fun of you so bad . But as I look around my garage I think I might be you .

[@owenskeen7855]

Please shout me out I’m very sick 🤒

[@SpecificLove7]

Hope you feel better

[@owenskeen7855]

Please shout me out please

[@rollingthunder4599]

Where do you find clear PVC?