10 Signs Your Rx8 Needs A Rebuild

[@Drivenbymadness]

⚡ *Check the health of your rotary engine by performing a easy & cheap compression test --> **kzbin.info/www/bejne/n4m9hmqBgLxppMU* ⚡

[@fc3sttwo]

I've had engine failure, trans failure, ssv valve failure, solenoids and air injection failure and power steering failure.. I'm adding a turbo soon and hope to make this list longer.

[@carlossantamaria7967]

Hahah how the project went !?? 😂😭

[@chinchy111]

@@carlossantamaria7967 it killed him

[@blackpsalmmusic9180]

@@chinchy111 i lol'd

[@PartiBuoy]

When rx8 owners think they have a problem they don’t.

[@That2007YZFR6THUNDERCAT]

​@@PartiBuoythe problem is the car

[@Psyrecx]

"If one of your windows doesn't roll down all the way..." "Gonna need to rebuild your engine"

[@MrBoxkev]

Lol

[@muaminhugsy4964]

Great video, awesome stuff, love how you had to say "dont touch the exhaust when its hot" because many people actually need that piece of advice XD

[@Drivenbymadness]

Thanks bro! hahah well, i agree on the fact that people never stop to amaze you :P

[@revan2814]

"if you consider buying an RX8, you might need to rebuild your engine"

[@xMorbidArtx]

Truest statement. If you bought the RX8, next thing you need to buy is the rebuild.

[@connieindahouse]

If you buy an RX8...you need an engine rebuild

[@aj_art8058]

2:54 I'm not sure if this is the same issue as what I faced however, when I got my rx8 at 40k miles it would make an awful rattling sound at rpms above 6k. It wasn't so much a knocking sound but a terrible rattling sound. I immediately thought the engine was screwed however it started fine hot and had no other issues. I read on an rx8 forum that many people experienced this and it was due to the rx8s not injecting enough oil to lubricate the housing. Rx8s as new as 7k miles were experiencing this. I first gave premixing a shot and within the first top up the car felt entirely different. That sound had gone away immediately and it felt easier to redline. I thought that this was only a temporary fix but 20,000 miles had passed and the car was still running smooth. At 60k I decided to fit a sohn adaptor kit, so that the car wasn't using dirty engine oil. I also kept premixing. Now I'm at around 80k miles and its still got a high compression, high 6s and 7s. Has anyone else experienced a weird rattling sound at high rpm? Its always been a rather strange thing that I never fully looked into.

[@josenieves7654]

was it a squeaky rattling sound? also i don’t know much about cars mines sputters everytime i rev it do you know the cause of this?

[@aj_art8058]

@@josenieves7654 Honestly I can't say for sure. Its best to check with a rotary specialist but what I will say is that with RX8's there are only really two things that can go wrong with them: 1) loss of compression over time or due to lack of lubrication - add premix with each fill up and you can extend your engine's life. 2)Coolant sealing wearing out causing car to overheat - this only ever happens if you rev you engine or drive hard before it properly warms up. Let your car warm up properly (10 to 15 mins of driving under 4k rpm) before building up revs. Once its warmed up properly you can redline it from time to time. Also never turn your car off if it hasn't ran for at least 5 mins; it needs to warm up before turning off - it not a car that can be started, moved to a different parking space and turned off. Its worth getting a compression test from specialists such as Essex Rotary, Rotary Motion or Rotary Revs. Just for peace of mind. Your car may be perfectly fine but worth getting an opinion from an expert. -In terms of sputtering, I suspect possibly spark plugs need replacing. I change my spark plugs every 6k miles, ignition coils and ht leads every 10k. I've attached some links to forums with similar issues. www.rx8club.com/series-i-trouble-shooting-95/sputtering-low-rpms-93146/ www.fixya.com/cars/t17230459-rx8_engine_sputter

[@josenieves7654]

@@aj_art8058 thank you very much

[@aj_art8058]

@@josenieves7654 No problem, good luck with your car. I'm sure everything will work out fine. I wasn't entirely sure about what vehicle I bought but learned along the way - and its still running fine. Worst case scenario, these cars happen to be the easiest engines to rebuild.

[@josephdevito3520]

Love this videos there really helpful i just bought a 2006 rx8 a week ago and i love it only has 49,800 miles on it with a decent amount of upgrades

[@Drivenbymadness]

Thank you so much man :D Awesome man! I'm very happy for you! Enjoy it as much as you can :D

[@geodangleon]

If you're watching this video, you're gonna need to rebuild your engine.

[@condolence1567]

Oh god I hope not

[@emoya319]

Fak

[@IAM-kc5ov]

😰😰😰😰😰😰

[@condolence1567]

I just bought my first car as a 1988 rx7. Trying to get it running tomorrow

[@That2007YZFR6THUNDERCAT]

GET RID OF IT PLEASSEEE or you gonna need an engine rebuild

[@raymond3232]

I'm so glad I watched this I was scared because sometimes I get mildly slow startups, nothing like in the video but I am revamping the ignition with BHR coils, new plugs, and new wires so this should go away. My engine has 118k mi on it but was very taken care of the orignial owner was a mazda mechanic and I bought it from his brother so basically the same.

[@Buildingolives]

I got a 2004 mazdar rx8 that hasn't been used since 2011

[@gunnerguy31]

It's time to rebuild

[@christopherspence7726]

Hey man. Love your videos. I just bought a 2004 Mazda rx8 last night. I love the car so far. It has full Mazda speed racing exhaust and a cat less mid pipe. It does have a engine light on for the 02 sensor. And it sometimes has a bouncy idle not all the time but sometimes. No smoke or anything. Really just looking to see what all I should really for. I'm new to rotarys but I've done tons of research. The guy did a rebuild 10k miles ago but then again it could have problems

[@Drivenbymadness]

Hey! Nice :) I think the bouncy idle is more a ignition problem than a low compression. Try replacing your coils, wires and spark plugs. and this will also help not burning out O2 sensors , so you can replace it, and it will work fine :)

[@christopherspence7726]

Driven by madness thank you very much :D

[@chinchy111]

@@christopherspence7726 still have the mazda?

[@christopherspence7726]

@@chinchy111 sold to a buddy of mine a few backs back. Still going strong

[@jimmymartin]

I don't have any of these symptoms. Car cranks but doesn't start and back fired once out the intake. Took it to mazda and said it's the catalytic converter that's all clogged up. Before the engine ran perfectly fine and produced great power.

[@georgealtezza5235]

In the next video you should restore your headlights!

[@Drivenbymadness]

George Altezza if it makes you happy ill do it :)

[@sofakingdom3076]

Easy to do. :)

[@connorreid5812]

Just bought my 3rd one has funny issue was driving fine but I pulled over from purchase and yep glowing cat..i gutted it and put it back on and a day later car is throwing 6 codes for all kinds of things like missfires and car takes 40 seconds to start cold or hot and runs like cheap won't even rev up to 5000 rpm

[@furkanterazi]

I'm not have a rx8, but i will glady watch your videos. Because i planning buy a mazda rx8 r3 in next 2 year. Because already i have megane IV 1.2 tce, i want second car for some iconic performance car using in the weekend. Mazda rx8 r3 is the best good solition for that :) But in Turkey dexelia oil and fl22 breaking fulids finding is real problem, if i will find amazon or ebay. I'll buy large amount. Anyway thank you for videos...

[@stevengravett4461]

My compression is 6 on rear rotor and just under 6 on front. Car still runs and starts with no issue

[@Drivenbymadness]

That's good :)

[@stevengravett4461]

@@Drivenbymadness it needs a rebuild soon but no issues with it at all. So see how it goes

[@Admiral-Dolphin]

Almost 10k subs💪🏻 I love your Contend

[@Drivenbymadness]

Yo Dolphin! Hope you don't get too high on that sea weed :P Thank you so much bro!!!!! And most importantly, thanks for being part of it

[@kevinmadrid9785]

My car has no check engine light changed all spark plugs coils and wires and starts just fine with no white smoke but the idle fluctuates between 1000 and 700 rpm.

[@doc.voltold4232]

How hard is it to pull the engine out?

[@mrgokarcik1084]

Doc. Volt engine weight ~90kg

[@christopherspence7726]

My neighbor worked for Mazda from 1980 to 1995. Said the engines weigh nothing. He said he's pulled 4 Rx7 engines out in a few hours

[@stevewelbert5039]

Awesome videos, my friend!!! What is the range of what the compression should be?

[@dablues7235]

I noticed your DSC light flashing. My flashes also. Is that a problem? My traction control light is also lit. Is that a problem? One more thing. How do you get your tire pressure light to stop blinking even though you know the air pressure is good? Thanks for your videos. I followed another one to fix power steering. So far so good. Also, how did you learn all this stuff?

[@testosteroneinc.3800]

2:00 We get it, you vape 🙄

[@Drivenbymadness]

Don't be jelly 😛

[@xESPplayer500x]

What if it has hard starts when cold? It can be started with de flooding, but can easily flood

[@aidenmaughan6594]

How does too much oil hurt it

[@frontyardbuilds499]

I need help with my Rx8 do you have any type of contact information

[@gsav6937]

My rx8 just clicks no crank change starter to new one and no result any help ??

[@eternitykings4233]

Did you check your fuses lol

[@ve2430]

I found brand new rx8 engines. Not reman.. is that more reliable than a rebuilt one from a reputable shop? Price is the same.

[@luisg3713]

I recently bought one but it starts up but after a while it will turn off and it will run any clues ? No knocking or smoke ?

[@2Angelemerald2]

Rebuild my love.....

[@jalenrobinson5225]

Lol I still want one. How much does a engine rebuild cost?

[@Drivenbymadness]

2,5-3000$

[@silentreaperv2369]

If your seat belt doesn’t buckle you need an engine rebuild

[@luigimartinez7127]

Hey, I’ve seen all your videos about maintenance for the rx8 but nothing really about that goes in depth tutorial about a rx8 that doesn’t have power steering. So I did some research and did all the possibilities that could cause my car to not have (ps) cleaned the thoroughly checked the connections. Nothing seems broken or dirty. Checked the fuse but no power steering still

[@Drivenbymadness]

Best solution is to ask eitherTtexas rotary experts if you're from US, or Essex rotary specialists if you're from Europe :)

[@aimanakaostonpunyachannel7470]

I have a problem..after speeding for long distance then suddenly no throttle response..i pulled aside and engine shut off..i try to restart but cannot..after rest for 7-10 minutes,i can restart the car n no problem..whats the problem ehh??my 2nd problem when try to rev high rpm there is restriction sometime but most of the time can rev to high rpm..no knocking sound..whats the issue ehh

[@Szymon7573]

350£ for apex seals on essex rotary? Its 200$ on other websites

[@CheapGuitarsAndMore]

It has to be a rotary comp tester? Cant be a normal one?

[@Drivenbymadness]

Yes, you can do it also with a normal piston tester. O have a video that shows you how to do it on the rx8 :)

[@Flyingdutchy33]

Just want to give a quick shout out to RE:Worx, also located in the UK, currently rebuilding my 20B. (Howcome there are so many specialists in the UK huh?)

[@Drivenbymadness]

Awesome! When is the 20b scheduled to be ready ? ( Supply & demand i guess :P )

[@Flyingdutchy33]

Forgive me if I'm being vague in this regard, but: "In the spring". Saturday I'm getting the car back from the rollcage company. Then it's settling on which painter I deem holy enough to be blessed to touch my gentle body... It can be very sensitive, you know. But yeah, shit's moving forwards. Problem is I didnt keep that much of an exact track of where shits got to go, so re assembling may prove to be the biggest problem. Thumbs up for planning ahead.

[@Drivenbymadness]

rollcage , nice :D hahah MR. sensitivity :P Awesome, hope you manage to finish everything this year! Same to you bro ;)

[@tr4c351]

The good old apex seal

[@96pabard]

Hey! I've got a question, is it best to keep using the OEM air filter or change to KN drop in? Hearing mixed arguments everywhere and not sure what to do/use! Awesome videos btw:)

[@Drivenbymadness]

Stick to the OEM, it will flow more than enough air to give you all the horsepower the engine has to give :)

[@ps3alphagamer12]

A true CAI either aem or mazdaspeed both are the same, is more a quality of life mod as cooler intake temps are an overall great benefit especially when you get rid of the oem intake tray to really let the engine get more air cooling. Basically all rx8 mods are quality of life mods or reliability mods. However going catless is paramount if you want your renisis to last. Oh also be advised if you do get a cold air intake it will require you to delete the vfad system which is basically just a little door that opens in the intake just before it actually hits the filter and basically its function it to get enough air required for 100% throttle opening. Basically what im sayin is you never truly get full throttle until this happens in the 5-6k rpm area then thats where all the power is made im am curious to see if there is a way to tell the ecu atleast in the s2 that vfad no longer needs to utilized and its good to give 100% throttle.

[@leledreher]

Hey man, loooov your videos! I'm in the market and just looked at one. It started up kinda well and repeadetly so when warm and had no smoke and stuff. But! I did the high rpm and lift off and head a noticable puff. Not a knock, but a puff like opening up a vacuum jar. Is this normal?

[@JoeJoe-ze1jm]

04 r8 really bad hard cold start and after it starts like3-5 min later with holding idle around 3k car shuts off, and then impossible to start. have to let it sit for few hours . Also temperature gets to 215F within those 3 to 5 min. Any suggestions of where to start looking for the problem?

[@ghostpro1293]

Joe Joe hot start issues if I’m assuming you’re letting the car get up to temp. If the car is not up to temp and you shut it off early it could be flooded because at 3k it’s dumping fuel. Check coolant because it sounds like it’s also overheating

[@JoeJoe-ze1jm]

@@ghostpro1293 thx for the info . But I did a compression test and its was pretty bad lol. new motor time

[@ghostpro1293]

Joe Joe that’s the worst. Sorry to hear but good luck and lmk how it goes!

[@odomis07]

Hey brotha what my 05 rx8 reads Anti Theft and will not start. I even change the batteries on the key fob and still not luck. Any suggestions?

[@Drivenbymadness]

Could be a flown fuse. Check the third one from the top in the fusebox underhood - 15 amps, marked 'engine'.

[@andriimandybura7731]

Hi guys! I have one idea - what if organise Europe rotary meeting in 2018? Don't have any thought's about location etc. In USA there are such event but I never heard about something like this in Europe. What do you think Chris?

[@Drivenbymadness]

I think it would be an amazing event, i was thinking of organising one, but not yet. Location in Europe is a bit trick. The optimal solution would be Austria or Germany, which is more or less in the middle. We'll see, i'll start small next year in my Country, and slowly expand :)

[@andriimandybura7731]

I think with your subscribers it possible to have some additional help) Let us know if you will plan something like this and together we can do it )

[@Hikarmeme]

Bit of an old video but I could use some input from someone. My FC takes like 2 seconds to start up from cold, my cold start system doesn't work. And for the first like 10-20 minutes of driving the idles surge between 1000 and 1500 rpm. And very rarely on hot starts the engine will stall unless I give it some gas. Other than that it runs good and holds idle at 700ish. From what I've heard this is either a TPS issue or an apex seal issue. Any thoughts? New to rotaries.

[@Drivenbymadness]

How old is the starter motor? If it's older than 5 years, replace it. It would also be good to replace spark plugs if they are older than 3 years. In combination with that, if your coils and wires are older than 4 years, definitely replace them.

[@Hikarmeme]

@@Drivenbymadness Just bought the car and I don't know much about its history other than its been premixed regularly. I'll start with the plugs and go from there. Thanks

[@kxpes]

Dam first video that is quite good

[@Drivenbymadness]

kxpes thanks 😊

[@ocbbronzy6541]

thanks a lot! nice information love it now i can take care and be prepared... hahaha

[@Drivenbymadness]

Thanks bro! 🌈 knowledge is power 🌈 😛

[@emynacar2064]

Hi i have a 2004 rx8 and i noticed oil in my air filter i have no idea what it is also have miss fire and MAP sensor code any suggestion on what to do please help

[@emynacar2064]

I replace spark plugs cables coils the sensor and still my car wont turn on and when it does after 10 min shuts down

[@tbonepumper5623]

was supposed to be grabbing a rx8 off my boss on thursday now im not so sure lol

[@Drivenbymadness]

Don't worry man, every problem has a solution. And i happen to upload videos that show you a solution to every problem you may encounter as an owner, and how to fix it by your self :)

[@edwinclairmonte4984]

@@Drivenbymadness hey how are you when I put my rx8 in drive (gear) the knocking goes away or lower to a minimum after I start my 2005 rx8 do you think it could be the ssv thing waiting in anticipation on you reply thank you my friend

[@iroh5733]

Hey could you somehow contact me so I can send a video of the start up and idle and tell me your opinion, I know the idle can be a little rough since there is no linkage according to the rx 8 club online and you should have a noticeable idle. But I just thought I would ask if it’s possible

[@Drivenbymadness]

Send it on facebook or on my email [e-mail]

[@FanaticFireworksF3]

"if you consider buying an rebuild engine you might need a RX8"

[@maxsonnenberg7791]

love your vids, currently about to get my license and really want an rx-8 any tips?

[@laurasutton6042]

Don't!

[@sofakingdom3076]

Have you bought one?

[@walidasansas8828]

@@sofakingdom3076 if he did he will probably need this : an engine rebuild

[@mrjackbilbo]

I am afraid while watching this video,. Lucky i dont have many symptoms

[@chavelodelgagao495]

Enun carro Mazda xr8 cuando prende y se apaga el motor ya no sirve

[@反骨水]

If u park ur rx8 for too long and disconnected battery as well,once ur started it the lights on dashboard were also gonna flashing like an EDM party🤣

[@Drivenbymadness]

反骨水 hahahha 😂 well, that's one way to start a party 👌 when I take out he battery, i usually leave it connected to a charger, so it keeps it charged in case I need it :)

[@反骨水]

Driven by madness thats why don't you trust "Long life battery"🤣🤣🤣

[@Drivenbymadness]

反骨水 long life of being empty 😂😂

[@反骨水]

Driven by madness hahah🤣🤣good one

[@randomchannel1712]

every problem this car has == engine rebuild AH YES RILAIBILITI

[@sled_neckx9972]

If the engine starts good both cold and hot, and no knocking, does that mean its in good shape?

[@sled_neckx9972]

I might buy an RX8 but dont have a compression tester.

[@Drivenbymadness]

and if there is no constant smoke coming from the exhaust, we could say yes :)

[@armarnigray]

Number 11, every time you burn a full tank.. 're build your engine

[@driverben]

I just bought a 05 rx8 and has 101087 miles on it but runs great, has a light on the dash and was told it wont start hot, is that minor?

[@ryanvick3755]

sounds like compression loss. you probably can still limp it along for another 20k though.

[@mbursian]

I would love to have a RX 8 :o

[@Drivenbymadness]

It's a great car to own, even with all it's faults :)

[@mbursian]

Yeah but if you buy one from someone you never know how they driven it ... a lot of rx8 they sell got engine problems and the fuel :( how much Liter/100km does your RX8 need?

[@H410R34CHR0CK5]

Marc Bursian I am 17 and I bought my RX-8 around 3 weeks ago. I have spent around $350.00CDN (91 octane). That is driving it for maybe an hour a day.

[@glock1inthetop45]

Heaton nice I’m 16 and I have a 04 rx8 I bought it blown up so I had to rebuild it

[@salvadorcastillo7330]

Its fun while it lasts😂 bout to rebuild mine for the first time

[@dublimited69]

knocking comes from imt solenoids not adjusting to rpm.

[@gerkav1008]

Check my small rotary video here kzbin.info/www/bejne/mWGmqWWgor-Dfa8

[@dakotarood2361]

Car starts, you need rebuild

[@paulscott1091]

you should rebuild your englne

[@thefury7410]

Have you drifted your RX-8 yet? If yes, then I want to ask something, when I tried to yank the e brake the other day it didn't lock the rear tires, so I had to clutch kick/floor it all the time. I just want to know whether it's only me or it's typical for RX-8. If your stock e brake can lock them, any possibility why mine can't? I've changed the pads and tightened the the e brake too (I made it a bit loose again because it was a bit too tight). You might have an opportunity to do a hydraulic e brake video someday (if yours don't work as well). Cheers :)

[@Drivenbymadness]

Very tipical. That's why i replaced my rear calipers in order to make the e brake actually work. When was the last time your bleeded your brakes ?

[@thefury7410]

Woah sorry for the late answer lol I didn't get any notification (must have missed it). I bleeded mine when I replaced the pads, well that goes without saying :) Should I replace the rear calipers or should I go with hydraulic e brake instead?

[@Drivenbymadness]

The Fury hydro would be useless if the rear calipers are not working properly. So I would fix the rear calipers and try to see how the handbrake works. If it good, there is no need for.a hydro, but if youre gonna drift.it, a hydro can be very practical 😊

[@thefury7410]

I'm still a beginner, so I guess hydro e brake can come later. Thanks :)

[@Drivenbymadness]

Yup, i'll put mine this year. but i can tell you from experience it best to start learning without it, otherwise you'll become too dependent on it :) You're welcome bro!

[@sofakingdom3076]

Rebuilding a Wankel rotary can be done in eight hours with the proper tools.

[@nhgriff1]

Anyone you recommend in U.S.?

[@aidaninkster8901]

i literally need 6 of the 10 :/

[@jaseindigo]

you’re lying if you don’t think 1:57 looks cool lol

[@iq-nj4xg]

Do you have shares in essex rotary 🤣 ?

[@Drivenbymadness]

perhaps :P

[@jgvbadv]

OI! Do you have a method to delete the gear change thing beeping? :D

[@Awsomeisimo]

Why would you tho?

[@jgvbadv]

@@Awsomeisimo Maybe cause i don't like the sound of it?

[@Awsomeisimo]

@@jgvbadv do you drive it at 8000-9000rpm at all times?

[@jgvbadv]

@@Awsomeisimo i drive it only 3-4 times a month and i don't spare it (read i redline it in most of the gears)

[@Awsomeisimo]

@@jgvbadv thought the car didnt mind being redlined occasionally?

[@rhhr9169]

Not buying one any more.

[@dctmatt]

tfw our rx8 needs a rebuild

[@emmettbraschnewitz]

I was hesitant to watch this video

[@2jzrx834]

My front rotor was a 4.2 and still ran lol only for a week tho

[@Drivenbymadness]

He was a fighter :) So now you have a 2jz in ? :D

[@2jzrx834]

Driven by madness haha nah I wish I just needed a name for KZbin

[@mrgokarcik1084]

haha your mazda stay in garage 90%of her life. am i right?

[@Drivenbymadness]

Mr Gokartboy 89% 😉 but thats because I constantly need to film. so its more on my jackstands than on the street 🐎

[@dystopia2412]

if you own an rx8 you need a rebuild

[@VeinTemperr]

What if your CAT is gone will the and the oil smoke continues what then?

[@Drivenbymadness]

If the smoke does not go away, and its very thick, then you have to remove the engine, inspect it, and see what's causing the issue. If you dont have a CAT, and you see a small bit of white smoke, its normal.

[@Medellinsfirearms]

Well mine just went... 110k miles

[@sofakingdom3076]

I hope to make it there. I have 50kmiles to go.

[@domminicpanoff105]

Nice video 😉

[@Drivenbymadness]

Thanks bro! 😃

[@CarloLeonKolega]

Problem one, cause: Compression/Apex seals - Rebuild engine Problem two, cause: Compression/Apex seals - Rebuild engine Problem 999, cause: Compression/Apex seals - Rebuild engine xD did I got it right?

[@brandonjones522]

I have a question 🙋‍♂️ what’s the highest mileage on a rotary engine without an rebuild???

[@04Eight]

I've read on rx8club forums that some had over 220k. I'm nearing 200k on my 04, no rebuild

[@dakotarood2361]

The rough idle, 700 rpm, and stalls in gear, and misfire, smoke smells like fuel,

[@mb4lunch]

#1, it currently runs..... LoL

[@daliborsucic2007]

When will you rebuild your engine?

[@Drivenbymadness]

Probably next year, but i'm gonna wait untill the compression starts dropping below 6.2 bar. I'm also thinking of doing a rx7 engine swap. Currently still talking details to the shop.

[@TroutFink]

Should be titled “10 reasons to not buy a Mazda rotary”

[@mrjackbilbo]

We rx8 owners beg to differ

[@euozdil]

biiiiiiiiiiiig thumbs up

[@heisenbergpinadrullard37]

the best rebuild you can do is swap the engine to a 1JZ or a 2JZ

[@sofakingdom3076]

No, the best rebuild is dropping in a 26b. Which makes 1400hp naturally aspirated, well the Mazda 787b did.

[@CheapGuitarsAndMore]

Just rebuild it every 3000 miles and you'll be good.

[@mb4lunch]

With each oil change...

[@sebastienhamill2478]

that's pushing it

[@That2007YZFR6THUNDERCAT]

When my rx8 grand touring needs an engine rebuild im going to burn it down and collect insurance on it i hate all rotory engines they suck

[@1991june]

Rx8 arent good daily’s more like a side car

[@sofakingdom3076]

I completely agree. I daily my Rx8. I drive mostly highway and maybe 40 miles a day.

[@suzumr2754]

@@sofakingdom3076 is 24 miles good enough for a rotary?

[@sofakingdom3076]

@@suzumr2754 personal preference to be honest. The content creator has a video explaining his cost in owning an Rx8. Go with your heart. I am currently at 70k miles and climbing. I couldn't be happier with my Rx8.

[@suzumr2754]

@@sofakingdom3076 I see. I'm thinking about picking a rx8 as my first car that *I* buy. I learned how to wrench on my starter car so I think I can care for a rotary. Of course, i'll be doing more research on it. The only thing that confuses me is premixing. Dump the whole bottle in or pour a little bit in?

[@sofakingdom3076]

@@suzumr2754 I'd do more research. It varies on how you'll drive it on that tank of fuel. I personally add 8 fl ounces vs my usual 4 if I'll be driving more aggressively. Reving to the moon in all gears. I use 4th gear my entire drive on the highway (70-120mph) 5th and 6th are considered over drive gears due to gear ratio. I say go for it whenever you feel ready.

[@sandervanderkammen9230]

#1, your car still has a Wankel engine.

[@ErrydayYe]

Rx8 trash

[@fernandoramalho3644]

Very shit engine....its all

[@gtlegacy8]

great car but rubbish engine