11.5 Mph on a KAYAK! Stable High speed Electric Kayak Motor! LAKE TEST fail and SUCCESS!

[@andrewschreiber362]

After everything going on in the world right now the smile on your face was absolutely worth watching this video

[@rogerbarrios8614]

Absolutely amazing. The world of kayaking is definitely changing. Thanks for sharing it.

[@armandolascano9348]

Ç😊😊😊

[@frankseville2136]

You need to make this a KIT for us to buy !!!! Want to make some great money build the kit start a business and get this out there... people would buy this NOW

[@obviousobvious8063]

I concur

[@mostblunted_211]

Yes please

[@hellabent]

Agreed

[@thinkaboutit9891]

Ready to pay today

[@mostblunted_211]

@@thinkaboutit9891 fax

[@louissippell1130]

I've powered 3 fishing kayaks over the past 5 years. Two using trilling motors and the last powered with a 9.9 gas motor. I had to build custom mounts (all mounted at the stern) for the motors, and never used over 1/4" 6061 plate I never had any bending or distortion of any kind.

[@anonamus4860]

Good job. But I must tell you when it comes to propelling a kayak the KISS rule applies. The more electronics you introduce on the water the more problems you will have. Electronic speed controls and motor drives will fail , if not from stress when prop gets fouled with weed or shallow water , corrosion will destroy them. I learnt this the hard way doing what you have done. In the end I fitted an off the shelf 12Volt brushed motor, 50 lb thrust , steered the kayak with the oars , fitted marine grade circuit breaker in case of prop fouling. No more problems, easy to maintain. Keep it simple on the water. Do more fishing than cruising. I prefer to use Lead Acid Battery over Lion . When Lion battery reaches low voltage state it just shut off, Lead Acid Battery will keep prop turning on 12Volt motor even at 6 volts, will be good enough to get you home without paddling.

[@mboyer68]

He's using lipo's which are so unbelievably much better than lead acid that I can't believe you even mentioned Pb acid. As little as 2 years ago, 8000mah lipo's would've been probably $250 each but they're cheap now. And the best thing about lipo batteries, when they die you take a nail gun and shoot a nail through the battery, shorting all the cells together, stand back and watch the show!

[@BlueOriginAire]

@@mboyer68 , I will look into the “lipo’s “ now...

[@fuqutube]

@@mboyer68 trash.. Pure trash

[@Heimbasteln]

A Lithium Pack with a BMS will shut off before the battery gets any damage. Your Lead Acid Battery will die very quick if you go below 12V. Even if you keep it above 12V it will not even come close to how long a LiFePo4 Battery lasts.

[@trevorgraham8302]

Also the feeling of zooming in a kayak after the hard work is one of the best I definitely understand why you couldn’t stop smiling feels like you got two giant outboards on there

[@torque350hp]

Not bad. I dont know how much cooling you need but when I did model boats we installed a water pickup angled off the drive prop to cool the engine and had the exit off the side of the hull so you could see it running. It may be an option for your project.

[@DIYunpolished]

This would be great!!! If he didn't do this he needs a radiator and fan in the loop on his water cooled ECU!

[@DIYunpolished]

It may could clog up the fins if there are any in the ECU cooling block. CPU coolers have fins. Idk if that does. If it does use a corrosion inhibitor and a radiator and fan. Your build will last and not have over heating issues. Good luck

[@DIYunpolished]

PC cooling hard Ware is your friend. I would use a 240mm radiator. You could get away with a thick 120mm rad with high fin density.

[@ysidroavila6454]

awesome.... not that its been some time, would you use different components or stay with the same?

[@pville5548]

I hope you include a total full power run until reaching safe voltage cutoff so you determine the usable time of the unit. As an experimental platform. the second one should have upgraded hardware to clean the kinks out a bit. Looks good so far. Good job.

[@frogmanencountersradio5462]

I'm raising money to fire him into the sun on the first Ugandan space flight

[@moneymanxd3648]

What a crazy idea man! It might look ridiculous but is actually genius. Kayaks with a motor takes them to another level

[@JpFishingBrasil]

what a crazy invention, man😲 you need to patent this... Awesome

[@bgi142]

Its not new people are already selling a way better motor not in water kits

[@hugoh.9694]

@@bgi142 Yet you don't provide any links or info. 🤦‍♂️

[@bgi142]

@@hugoh.9694 yea Google it dummy its a jetski motor propeller water intake wthat makes the motor be able to be out of the water way better than this fools prototype

[@TheGoodoftheLand]

It's always the loudest guy in the room that wrong. It's Jetski impeller, not "Jetski propeller" They are far less efficient than a propeller requiring dual motor and a ton of batteries. Click this link and watc the full video for more details. kzbin.info/www/bejne/epzOapqsidJ2jrs

[@hugoh.9694]

@@TK-oe1xm yeah. Okay. Let me just Google "way better motor" since that was the extent of the info you provided. Admit it. As my dad would say... your original comment was about "as useless as teets on a bull." And I'm the dummy. Lmao. Okay. 👍

[@The_D_Train]

Ah ha! I just a kayak with a trolling motor. I was thinking to myself, lipo brushless rc gear would be the go and there you are. Good work mate!

[@tomim7187]

When you punch it, the smile on your face says, "Christmas morning!"

[@MrMd5555]

Like watching somebody shoot a full auto machine gun, uncontrollable instant smile no matter who it is!!

[@somenygaard]

What lake is that? Beautiful.?These boats scare me around here too many gators. Great Job!

[@cliffelliott9331]

I love watching people making stuff just for the smile factor. Well done!

[@MagnusFabrication]

I mean theres the smile factor then theres the saving gas factor, the get to bew spots factor as well

[@BLagather]

I never thought I would see a kayak go fast enough to be up on plane. Wow!

[@fernandopiaba1]

1 A MORTE DE DIMAS - O PROCESSO DE DESENCARNAÇÃO - kzbin.info/www/bejne/qZK6lpaXl5Jqis0 2 Morri e Agora? Áudio Livro Espírita kzbin.info/www/bejne/l5vdq59vrcyqr68 3 Semeando e Colhendo - Contos Reencarnacionistas kzbin.info/www/bejne/raDJd32NeN1sq9E 4 Minha Vida na Outra Vida - kzbin.info/www/bejne/f5XEoXikpptokNE 5 Dois goles para três kzbin.info/www/bejne/sGa6foNoaqutZtU 6 A Reencarnação de Segismundo kzbin.info/www/bejne/aoK8h4N9aslqmNU 7 Sempre contigo senhor Jesus! kzbin.info/www/bejne/hKjJoaSIpZiriLc 8 Hora de desfazer os grilhões mentais de espiritos das trevas com a humanidade kzbin.info/www/bejne/maG7lKSngqmhZq8 9 O Vôo da Esperança 1/2 kzbin.info/www/bejne/bYfUp6WsmNBqntE 10 Agnus Dei ♪ Alleluia kzbin.info/www/bejne/aHzPaZKbgdaLpLM 11 Agnus Dei ♪ Alleluia Jotta A kzbin.info/www/bejne/r2WvhpZ7mNaVedk 12 Canalização com Akhenaton/Reunião alienígena,a entidade Jeová, Moisés, Elias e Eliseu. kzbin.info/www/bejne/l4XEZWx5ep6lY7c

[@jerrytalley802]

I know, how cool is it to see a kayak pass a gas outboard, lol

[@reidrobicheau9661]

You know you fully succeeded something when you have a smile on your face like that haha this is so awesome!

[@MAGNUSDRONES]

Wow! Great conversion!! All the benefits of electric power and a fun way to get to more fishing spots. Great job👍👍👍

[@sn0wchyld]

got an updated link for the prop? link in description doesnt work anymore

[@GreyerShade]

"This is as fast as Im ever guna drive....." Yeah RIGHT! 😂😅🤣🤣

[@01Joemama]

that smile bro, i was the same when i built v1, now I'm building a v2 with more power bigger prop and customising the whole rear end of the kayak to look like nothing on this world haha but the stability has gone thru the roof, i will be able to stand whilst in motion. good job on the build by the way

[@customboatscreensolutions5893]

Anything that puts a smile on your... Thats what lifes all bout

[@rainbows99]

It’s so good to see someone pioneer someone something new

[@Ziptietechnician]

Don't need machine tools. You would be suprized what you can build with a hacksaw, grinder, drill, and file.

[@01Joemama]

that's all I needed for my kayak build and I'm only using the same for my v2

[@Bikedueder]

That is awesome, and overbuilt in a good way. I just spent the afternoon making a trolling motor mount for my kayak, All heavy wall metal electrical conduit. I re-angled the rod holders and it slips in tight with no wobbling or play. One piece welded unit. Still keeping the paddle, just in case.

[@Welphereweareagain]

I’m not sure, but I think you made a trolling motor? With lithium ion batteries?

[@gunzzzz89]

Is the motor water friendly?

[@wesh388]

Absolutely amazing, quality work you did there. Nicely done

[@bigfatdaddydan5478]

Great video! Good going. I do have a question for you though. At 9:25 you point out "I'm waiting for another one of these". I so need one of 'these' also for a build I'm doing. Please let me (us) know. Thanks, Dan

[@krisztiankiss1034]

Its awesome Bro!!! Respect from Europe Hungary :))

[@carlosgenen8848]

Hola sos un genio! felicitaciones!!! te consulto el motor lo hiciste tu o lo compraste, tengo un kayak y me gusto su eficiencia, me asesoras por favor?

[@StottEric]

I’m interested to know the total cost?

[@ryanbernard6550]

Those brackets he made would be pretty expensive to buy cause he made everything out of slab Al Edit: that custom transom he fabbed would be veryyyyyy expensive

[@TheGoodoftheLand]

+Ryan Bernard Check out the previous video. The aluminum was $6 at the scrap yard. That is the only reason it is so thick.

[@jkreviea]

What esc do you have?

[@neogator26]

I love it! I love messing around with motors and electricity. I really love how you now get the Tesla effect in your kayak. lol You can't punch that motor without smiling!

[@antoniohuertas8909]

That thing is frickin awesome! Man, I give it to you for successfully pulling it off and finding ways to make it better. I tip my hat to you sir!

[@avryptickle]

That looks like the hell of a lot of fun.

[@kaylor87]

Just paused at about 16:30 -- question. The water pump hooks up to the speed controller and circulates water... But it's a closed system, and the water doesn't pass through any sort of radiator or anything in your setup. If that's the case, will the water cooling really even help that much? I would think it might delay the heat, but over time, with use, the water temp is going to get just as warm as the speed controller with nowhere for that heat to dissipate? I mean, I spose just running it through the hose and bottle might help dissipate, but I would think that with a radiator, it would be much more efficient.

[@TheGoodoftheLand]

+kaylor87 Correct. While the volume of water in the system helps to dissipate the heat if given enough time it will significantly decrease in efficiency. A proper cooling system.is coming. This was a quick test rig. You will love the full system.

[@kaylor87]

@@TheGoodoftheLand Heck yeah, can't wait to see the finished product!! What an awesome build (: Thanks for the content, man!

[@ww07ff]

Hey Justin, you should lower the propeller "as deep as you can", it raises the water column (water pressure) above/behind the propeller, reducing the chance of cavitation around the impeller blades (power losses). Great project! Regards from Brazil!

[@gingerkitty1374]

What? Ventilation is not cavitation. A simple "fence" would stop the intrusion of air into the propeller. Fact, you raise an engine to get more speed. Sorry my friend.

[@ww07ff]

@@gingerkitty1374 Do you know the boiling water temperature at the top of Everest? In Celsius, for obvious reasons.

[@paradiselost9946]

@@ww07ff generally, anyone with "kitty" in their name is a moron ;) now i wanna give my outboard a 10M leg...

[@paulherman9599]

Not an engineer or tech guy but LOVE ALL use of Electric! It will get you there!!

[@robertbragg9364]

You're some kind of monster garage kind of genius! I have 100s of ideas and you could make them all come to fruition. Great video

[@itsrobotime]

have you explored any of your ideas one year later?

[@robertbragg9364]

@@itsrobotime I'm constantly making things from nothing or making things better. Whatever I can do in my free time.

[@itsrobotime]

@@robertbragg9364 sweet! glad to know you're chasing those ideas

[@robertbragg9364]

@@itsrobotime I appreciate that. Some people enjoy sports but not me. I wanna know how everything works, how to fix everything and I fix things for people as often as possible. I had to go back to work for someone else because working for free constantly doesn't pay the bills. Ill always fix and create things as often as possible but for now I have to be an adult and be responsible. Whomp whomp whomp

[@itsrobotime]

@@robertbragg9364 I’m much the same. Ideas just flow from my head like a burst dam it’s pretty hard to find the balance between dreaming and living. I hope everything will continue to be alright for you

[@4thGloryMonday]

love it but how hot does the water n the bottle get? hate to see that esc burned up

[@macrumpton]

If you were using a planing hull instead of a displacement hull (like all kayaks) you could double your speed and reduce power requirements.

[@RATsnak3]

I think fundamentally changing the design of the boat kinda defeats the entire purpose...

[@brenthawkins204]

Yea a solo skiff hull is what you need to plane out

[@boatlover2296]

The thickness of your material is big enough for a full size outboard. Awesome work

[@ScruffyOldJimbo]

Awesome work, I've really enjoyed this build, thanks for your trouble, fantastic result. I need to find a motor I can run in saltwater without it corroding then get building something similar.

[@Apparition_Unknown]

We are actually building some for Garmin right now we have a fresh water and saltwater version in development

[@ScruffyOldJimbo]

@@Apparition_Unknown Look forward to seeing more on that. Such a shame this series of videos here appears to have been abandoned though, I was really enjoying them.

[@ABRITUSS]

All project prices mator controller battery???

[@wellheadcajun5664]

Such a cool build. I was in the seat when you opened her up and the first thing in my mind was wondering about the steering being fluid enough to turn without turning over.

[@ASKR303]

Hi. Would a larger propeller create more speed? I'm thinking of making a pedal power system

[@totherarf]

"That's probably fast enough right there!" ..... Cranks it up and cranks the Grin up too!

[@TheGoodoftheLand]

+Dave W 😁

[@dominictarrsailing]

even when the camera isn't on you, I can *hear* the giant smile on your face when you are letting it rip!

[@smokecreekstudio7320]

Is the thickness of plate wayyyy over kill?

[@dcgo44r]

Definitely, but is great if happened to have it around and avoiding spend more money and time!

[@lkend2]

U could mount a 50 hp outboard to that thing holy f#%k

[@stevenraycopley8885]

Nah man. 1) Overkill is overrated 2) Moderation is for cowards 😂🤣

[@jamessieber7095]

i just added a minn kota to my rig native water craft 13.5 ft long 41 inch wide , but yours is a very interesting project i might take in the future. like the speed . in the back for the cable tension and angle . an angle bracket with stainless steel pulleys or aluminum , make em or buy em. 3 inch long 1.5 inch at the middle apex of the triangle and it would give you the slide and relieve the tension on the material so it would not fray.

[@mikewheeler352]

Anytime you can create a wake in a kayak you were going somewhere fast. Great build 👍and tight lines

[@fhaquuu]

It’s a matter of time until bikes, kayaks all come with option!! Super cool.

[@GreatPlainsKayakAngler]

Amazingly cool build, I’m so envious!!

[@bastiendroz4329]

Super DIY project! Congratulation. What kind of propeller did you use ? The link you provided don't show the exact model. One more question : I have seen that you use the 360KV motor model. What is your feeling about a higer KV based on your experience ? Thanks so much for sharing.

[@danw1955]

That thing will be nuts with the higher voltage packs! Considering the amount of draw on that controller, you might want to make a heat exchanger out of an old heater core or something, so you can keep it submerged. That water bottle is going to get hot in a short while and burn up your nice 300 amp controller. I think you might want to invest in a better pump also. Those washer pumps are made for intermittent duty, so they won't last very long. If you can find one from an old water cooled computer setup, they're quiet and made to run continuously at 12v. Can't wait to see more on this!😁

[@ryanbernard6550]

A D5 pump

[@mohammadhashemi1771]

Nice work well done, how much power in watts do you think you need to push a kayak at let's say 10mph for 1 hour?

[@TheGoodoftheLand]

Quit a bit. The trick is keeping the amps down and hitting 10 mph. The escs that I've tested so far are not up to the task. Update soon.

[@mohammadhashemi1771]

@@TheGoodoftheLand understood and thank you sir, but what is quite a bit can you give a figure or is it too early for that and more testing is needed

[@Kiba69420]

"Lets see how it compares!" Translation "Lets see if my 1 occupant lighter kayak with an electric motor can beat your aluminum flat bottom with 3 occupants and a 5hp motor!" Hm, im 26 seconds in and im anxious with anticipation of who is going to win this race!

[@ezhvladimir]

Hello! What is the maximum static thrust? Why did they change the controller?

[@chittlingwhittles1198]

Just a heads up if you plan on continuing with this without ELECTROFISHING. I would advise to protect against Ingress of any sharp sediment settling between the rotor and the stator which will strip the winding coating. This will cause a massive short which could potentially hurt you considering you plan to run a higher voltage. Please stay safe.

[@phantomdoesgames]

Do you know where I can purchase one of those?

[@youngestpersonalive]

Lol ELECTROFISHING... could it be dangerous?

[@Eden_M]

@@phantomdoesgames Take a look in my channel

[@youngestpersonalive]

Vladimir Herceg what’s the worst that could happen

[@chittlingwhittles1198]

Big Pete I hope you’re joking.

[@diamonddynamics_official]

Love your vibe-super chill and professional at the same time!

[@TheGrtpmkn]

Holy Moly...that's nuts...now I'm pricing parts

[@SuperTender11]

What equipment did you buy? Motor and esc?

[@robertsperuta6035]

when do you start putting them into production.....i want one.

[@robertsperuta6035]

@@owenair8242 can you send me the link....thank you

[@davidjackson7051]

I'm definitely building me one this winter thanks for the inspiration

[@jamesraftos3586]

Love your work brother, you have inspired me to do something similar to my kayak. I’m looking to run approximately 90 volts with a huge 720 phase amps controller. Looking to have a lot fun with it but mostly using it for slower speed trolling and fishing. I current setup is only 5 horsepower which is quite primitive in design but still a lot of fun. Can’t wait to install the big system this weekend. All the very best to you and your family.

[@shh..5369]

Should show in video would be good to learn from

[@Nug-one87]

Hey dude. I have a jackson cuda 12. Can I get instructions on how to build your bracket?

[@whitecompany18]

Decent! Maybe streamline the vertical shaft like an outboards prop shaft casing , it would also work like a rudder for steering without power. Great vid buddy

[@amandeepthakur1524]

Put a smile on my face. This is awesome sir. Ur a smart guy.

[@ryanharris6102]

That's a lot of aluminum. I bet that mount could hold a cummins lol 💪

[@alienxyt]

Yeah, I thought Chevy 350.

[@Mad.Man.Marine]

Def could be lightened up a ton. Lots of lightning holes would help a lot.

[@robertkemp9685]

Grossly over engineered compared to the strength of the Hull material that is soo over the top, just my opinion

[@TheGoodoftheLand]

I would say under engineered,over built. I don't have the skills to calculate stress loads so that issue is solved by not having to worry about it. Probably didn't see the video where I collected the material but it was $6 from a scrap yard and the final weight of the bracket itself is just over two lbs. Not bad for a backyard diy project.

[@ryanharris6102]

@@TheGoodoftheLand no problem with building something stronger then it needs to be I was being honest when I said I bet it could hold a cummins with it being that strong a couple some supports to it and it could hold what ever power you put on it as long as it doesn't tear up your kayak

[@kaseybowen]

Man of the year right here!

[@rcguy5793]

Awesome work buddy!! I do high speed rc cars. (120-150mph) the sss motor in your video works great. If you want more power run two of them this will allow you to use even larger props by splitting the load. Not sure how you could mechanically mount two on there but all of the high speed rc boats run twin motors on twin seaking escs. You would literally almost your mph

[@ZT_Performance]

Hell yea 30mph would be my goal atleast 🤣

[@siggyretburns7523]

I'm glad it turned out like you wanted. But kayak hulls just weren't designed for speed. You need something more flat and wider. But the important thing is you got the power figured out. Good job.👍

[@williamfraser]

Sweet ride! I would love to know the current draw at various speed settings. Good luck with your further development.

[@TheGoodoftheLand]

+William Fraser That info is on the way!

[@robertotx782]

Tem kit a venda ?

[@jeffstevens156]

THAT IS JUST SOOO COOL! I’m impatiently waiting to see the duration. You could eliminate the need for a small motor AND a trolling motor in one fell swoop. AWESOME!

[@TheGoodoftheLand]

There is another video after this one. It's the long range test. I am also uploading another as we speak! You are two behind!

[@jeffstevens156]

The Good of the Land Thanks! I’m glad to see that You show the proper respect for a safe working environment. Face shield for things that could possibly come undone and even a PFD. Great series. I can’t wait till You get it to the market. If You go that far. Still, lots of information.

[@trialnterror]

They are called solder sleeves! I use them on the A10 all the time! Nice to see a link where you can get decent ones on the open market!

[@MrMd5555]

A10 meaning like A10 warthog.. Aircraft?

[@trialnterror]

@@MrMd5555 👍yes sir

[@MrMd5555]

@@trialnterror well that's about the most badass thing I've heard all day. I've always loved jet aircrafts from a young age & the tank buster was always at the top of my favorite list

[@mikemclitus7162]

Actually i use them at work and we order them as "solder ferrals." I know its spelled wrong. Just thought they should be called what they are. Have a nice day. Awesome video.

[@lmiller4560]

I am working on motorizing my kayak. I wonder if you thought about using super or ultra caps and only one battery pack to maintain the capacitor voltage while the caps buffer the instant load on the batteries.

[@RR-id4rh]

dude, your machining is clean af. nicely done

[@christopherconkright1317]

The bottle will heat up quick? do you leave it in the lake to stay cool?

[@DIYunpolished]

You should get a shirt that says. "Makes me happy"

[@nealewatson5284]

Impressive. What kind of motor is that?

[@adamweintraub6274]

Once you get it figured out you need to sell them. This would turn my canoe in to a rocket.

[@Jettjohnson4]

Adam Weintraub I would buy one

[@bleezham]

@@Jettjohnson4 ditto

[@212acres3]

I’ll get one!

[@consaka1]

@Mik Wri I'm surprised the Chinese haven't made one then. They love going after overpriced stuff and making it cheaper.

[@bleezham]

Ill venmo cash for a trolling motor kit.....maybe utilize and old m8nkota as framework

[@joshtalbott9528]

How much did it cost to build the jet and the battery? Would a 50' cord to the motor change performance?

[@airraptor]

guys have a internal combustion engine on their boat and they call it a motor. Guys with a motor on their boat call it an engine.................. lol

[@ryanbernard6550]

Spinny boi?

[@lapaloma387]

It's like, Park on a Driveway but Drive on a Parkway

[@camerondeans8277]

Great work, I'm excited. Any updates in terms of the longevity of the battery and motor options? The link to the impeller doesn't seem to work, would you mind sharing which one you would go with?

[@K3Flyguy]

When you get this all sorts out I would be very interested in purchasing your plans/kits/systems for my yak! I have far more trust in your method than the mass production manufactured cheap crap being offered these days.

[@mehmetdtx]

How much did the outboard cost along with electronics but excluding the bracket?

[@sparkyprojects]

I can see Hydrofoils in the future :D

[@TheGoodoftheLand]

+Sparky Projects Sparky ,you are a wizard! After this video I added one.

[@lisathayer9170]

Could you put a solar panel to help keep a charge or so when you stop to fish it can add a little charge

[@lolamarie7321]

I want a man like you 😩😩 easy on the eyes good with his hands and love for nature..

[@seanorth]

Don’t we all 😄

[@CarlosContreras-ko2ek]

Great video! Most impressed by your level of knowledge, intelligence. A vitamin bottle! Go work for nasa. Great job!

[@dragonsuicida1]

Bought 2 kajaks 2 years ago, used them only once. (Not enough horse power.) After seeing this, I think I am going to try modifying a trolling motor... I think you did a great job, it looks awesome...

[@petecampa]

Elon Musk (Tesla) just called...🤑

[@briane3050]

Have you wrapped up some final builds yet? I donated to the cause but hadn't seen any final configurations on the kayaks, so I just wanted to mame sure maybe I just missed the video for that???

[@patrickradcliffe3837]

Surprised it didn't sink by the stern. Overkill taken to Nth degree, next one you should cut the thickness by at least half! You not putting a V8 outdrive on your kayak.

[@TheGoodoftheLand]

Its aluminum. The entire thing weighs five lbs. The battery is less than 10. This kayak can carry 450 lbs. The material used is certainly overkill but it plus several other pieces were picked up at the local scrap yard for $6. Can't beat that price for a prototype. I'm with you in thinking the ones made available for purchase could be 2/3 thinner.

[@patonbike]

I like that mount with contact points on 2 different planes. What is the wattage it takes to go 11.5mph? Do you know of any tandem boats that'd have mounting points similar to yours ?

[@Maxim.Teleguz]

I can imagine you never have to excercise again.

[@tribalncgaming1091]

luckily there is this diet called KETO so you can drop down to your natural body weight without excercise :)

[@bearbuchanan8341]

good moorning. would like to no what the name of the meter is that you use to test the speed /distance /volts /time .im looking for one fore my kayak were can i buy one

[@TheGoodoftheLand]

I found it on Amazon. It's a 500amp shunt based battery management. I will put a link in the next video. I believe it was $75. It is a hust have. I also picked up some digital temp sensors with built in switching relays for the cooling system I'm building. Lots of good stuff on the way.

[@madaboutbrens]

Hi, I am building a scuba DPV you have the motor immersed completely, how did you waterproof it ? I followed the link but it says the motor isn’t waterproof which is why I am asking the question I guess 😊

[@heartsky]

The drone footage cut at the end with outro music...perfect.