13 Tools I’ve NEVER used as a handyman.

[@drengskap]

This seems like a real case of 'your mileage may vary' - most of those tools or similar get used by me on a regular basis in a light engineering/mechanics workshop. OK, not that weird Ridgid plumbing tool, but small hacksaws, step drills, needle nose locking pliers, soft hammers, stubby screwdrivers - all essential everyday tools as far as I'm concerned. And the claw tool is good for unblocking drains!

[@pzwolski]

The snips you showed are not left or right handed. 🤣 They are to make left or right turn cuts in the steel sheets easier. Or straight ones. 😁 Therefore there are 3 of them: Red - right turn cut Yellow - straight cut Green - left turn cut

[@JAGWAC]

For sure! Slip of the tongue. Thanks for the comment 😎

[@KenImduaikiat]

Plastic mallet is useful for taping plastic anchor into a concrete wall with out damaging the paint.

[@AlexSwanson-rw7cv]

That type of hammer is good for assembling steel frame garage shelving, assembling some flat-pack furniture, and woodworking with dowels and some other joints. I use small needle-nose vice grips too but not for "handyman" stuff.

[@riolopez4079]

Apartment maintenance here, the flex extender (non-right angle) has been invaluable to me

[@vf5126]

My version of the Rigid Plumbing tool has paid for itself in Apt. maintenance.. The metal ends pop out for different uses (sink or tub drains), or the entire piece can straddle a hose up behind a sink; makes working alone easier ~

[@sandy_knight]

I have a Felo T-handle just like yours (its a Torx25 rather than for 1/4" bits but the handle is exactly the same) and it often gets used for removing disc rotor bolts on mountain bikes. Its not for extra torque but for getting all my weight into the tool when I have to remove a bolt with a worn/partially rounded (cammed out) head.

[@MORGANSMaintenance]

I am the same on a lot of those. I have them, but don’t use many of them very often… other than step bits and the Ridgid Plumbing Tool. I think my Ridgid tool is older though, or maybe newer… but I don’t think mine is as big as yours. I never bought the flex right angle, I always felt like it would take too many hands. I’m an going to have to get me a Klein Slotted Screwdriver like the Phillips you have here though. I’ve always thought it would be weird to use, but I’ve seen enough people talk about how much they like them that I’m going to have to try it. Thanks for sharing 👍

[@qzetu]

Of course, this doesn't apply to all handyman because they all have different levels of skill. I have more than 10 years as a handyman. (1) I own a flex claw and never used it either. I tend to use my magnet extender more to reach for screws. (2) I use a mallet alll the time to install vinyl plank, laminate, and to hit on delicate things like a glass door that is requiring new rollers or framing, etc. (3) lmao i own that rigid plumbing tool and never used it once. And i really wanted it. (4) i use the mini hacksaw all the time when i need to cut something quick. Ive been in a few situations where the mini havksaw was the only thing that wouid do the job. It is a necessary tool for me. (5) ive never needed the needlenose vise grips. But they are good for servicing my tools, such as pinching off gas lines. I do landscaping as well. (6) i use snips all the time not just on sheet metal. I keep a straight pair for general work like installing duct or gutters. They also cut plastic and other thick material. They are essential in my kit. (7) step bits are absolutely fundamental. I use them a lot for custom work like drilling holes into metal in order to secure it to something. (8) the screwdriver can be used for all kinds of things. The sceew driver you have is a matter of preference, nothing more. (9) the T handle is the same case. Some guys use them, though it is not common. (10) never owned or needed a flexible right angle attachment. I do use my dewalt right angled attachment all the time. (11) the offset screw driver is another case of preference. I think most people tend to use the flat head more, for outlet covers. (12) I use the stubby all the time. Especially when installing ceiling fans because on some mounting covers you can't get to it any other way. The stubby is a fundamental part of my kit.

[@cobuck4007]

Great videos! You mentioned starting your handyman business a year ago. It would be great to hear about how you came to move in that direction and what the experience has been like so far.

[@JAGWAC]

Thanks for the comment! Its been a little over a year since I “officially” started my business. Sometime in the near future I’ll talk about it. 😎

[@neeko7878]

I use the claw to grab cloths from behind the dryer. 👍👍👍

[@PoorWays]

As a plumber's experience in new construction and repairs I think the only one of those tools that still come in handy once in a while are the stubby screwdrivers. I think most of those situations came into play installing large 120 gallon solar water heaters. They can take over 50% more space than regular ones and retrofitting them sometimes reduces alot of clearances on electrical issues.

[@hachi-rokuperformancegroup3987]

You need both left and right snips to make clean cuts. One cuts clean to the left and the other cuts clean to the right and doesn't matter in you are right or left handed lol

[@BruceAllgire]

Agreed. Red is left, green is right - I use all three, depending on the job.

[@jackof1]

I do primarily furniture assembly and the soft face hammer is one of my top 5 tools for getting that junk to “comply”. I also have the exact Wiha stubby and I love it! It doesn’t take up much space in the bag and good for reaching into tight spaces like inside drawers

[@JAGWAC]

I do a lot of furniture also and have a large non marking rubber mallet, this little one just seems too small and redundant. I’m holding out hope that the stubby will come in handy so I’ll keep it on the truck 🤞 thanks for you comment 😎

[@gregorymacneil2836]

I agree! I have two sizes of the Estwing and use them constantly!

[@anirbanacharya2181]

Honest review of tools bought with hard earned money . The first product is sold in lndia as kitchen drain cleaner/tangled hairball remover. But it can be used for odd jobs by attaching a small magnet in the grip . The odd hacksaw can be used by reversing the blade with teeth in inside direction and at constrained spaces where you keep on slipping/ missing the mark . The offset screwdrivers cannot be used properly but an offset spinner can be given a try . Wooden mallets are always better than rubber mallets .

[@skid7519]

I can see the reason for all the tools on your list except 3, the soft hammer, the straight snips, and the needle nose vise grips. I threw my left and right cut snips in the old box and only buy straight versions now. I can see using the right cuts though. The soft hammer I could see not using for some ppl but I use mine daily and have 3 or 4 different kinds. My biggest one that is different from yours is the vise grips, I use that exact pair for all kinds of stuff they are especially great at holding small parts and grinding or cutting with a porta band, I just use em all the time Nice list, it's cool to see what other people use, or dont use in this case. Cheers. Oh I also have a 100 in 1 drain tool that I would love to find a use for, its smaller than yours and has like 2 sizes on each end but I can't find a drain that any of it will fit hahah.

[@jaaqess2525]

I keep my Klein flip sockets on my stubby so it takes up less room. I rarely need the stubby and the flip sockets usually get put on an impact driver, but if it’s just one odd bolt I can just use the stubby handle with the flip socket. Klein makes a very small ratcheting driver that I love. It doesn’t get used much, but when it does it is the only tool for the job. Used it today to take the backplate off some 2x4 ceiling grid lights that were under ductwork. Stubby was too tall to get on it.

[@AidarSamudinov]

A stubby screwdriver is perfect for a jobsite where people like to borrow your things, ain't nobody snatching that piece of work 😂😂

[@kevindesilva1311]

Interesting , I have been doing \carpentry joinery and general maintenance for 47 years in the UK .I use my stepped drills all the time on wood , metal and plastic. Never use spade bits . Soft face hammer every other day (Thor brand) . Stubyy gets me out of the mire every now and then used it yesterday for the first time in ages. Hacksaw handle all the time so much so that I have never felt the need to buy a recip saw. Total agree with you on the rigid plumbs tool total waste of space. My everyday tools are a Bacho ratchet screwdriver with bits in the handle , a wooden handled square bradawl and Bakuma 8" restorers pry bar

[@2tana22]

Been checking your videos out, like your style with plenty of expierence, it shows, I’ve got 45 years, same kinda work, with still the same truck (70 Chevy 1 ton) loaded with everything possible too, I’m laughing at what you don’t use, think I’ll go through my truck and do the same, there’s a lot in there I haven’t touched for a long time, work I really rather not do to at my age… haha

[@gr8phil]

Good video, I agree with most of those. I tend to use a cloth over a hammer to do the odd mallet work, just to avoid carrying lots of tools in my toolbag. Stubbies are hard on the palm, but once in a while when there are access issues, not bad to have. My Wera tends to cover 95% of my screwdriver needs. The rest fall into the specialty and gimmick abyss that promise magic and don't deliver!

[@trezzh4]

I use similair rubber mallet all the time to ''persuade" plastic wall plug to fit into a hole. Steel hammers are inferior for thos task because they tend to smash plugs walls.

[@toekin6376]

Great video! I have a couple of stubbys and feel the same way, never call for em or even lend em out. Did I really need to buy all the tiny Knipex pliers? There are a few other tools no doubt but the biggest offender are freaking bits! Who doesn't have millions of useless bits floating around drawers and bags! Ha! you've got me scrounging through stuff looking for unused and questionable purchases. 😄

[@JAGWAC]

The bits!!! Totally have too many of those and I continue to toss them left and right. After this video I found a few more “never use” tools. Someday I’ll make a follow up. Still working on getting a full truck tour posted. Thanks for the comment!

[@jeffwolf8018]

Those arelittle hacksaws come in very handy when you're cutting the hold down bolts after they've been tightened tightened down a few times.. especially if you have a sink cabinet right on top of you

[@JAGWAC]

Its been a year since I posted this video. I still carry a little hacksaw but still no reason to use it. Same for the other tools 🤷‍♂️ thanks for the comment 😎

[@Russell8021]

The only thing I use that Ridgid faucet tool for is breaking the tub drains loose.

[@CarlYota]

I just bought that Rigid 500 in 1 plumbing tool. I haven’t used it yet but the reason I got it was to tighten the plastic nuts on stuff. And to turn those old oval shaped shut off valves because putting pliers on them usually destroys them. Although when they don’t comply I usually cut them off and put new quarter turns on instead. I’m hoping it actually fits behind sinks though because getting up to those plastic nuts is the main reason I bought it.

[@JAGWAC]

I hope you find some use. since making this video I still haven't found a situation where it worked 🤷‍♂

[@kendallas3705]

I use the hack saw for toilet bolts, snips for duct work, that rigid plumbing tool is a pos that works 1 in 25 times, I keep an assortment of bits in my general bag but have used about 4 of them. I dont carry the rest.

[@JAGWAC]

Yeah that plumbing tool stinks. Thanks for the comment ken!

[@jaywood8296]

Contractor for 40+ years, & I pretty much agree, but I use the snips and every once in a while most of the others. It's good to try stuff 'tho as it will soon be gone and maybe 1 in 15 is a winner. That plumbing tool is one of the worst for size vs lack of function. I think I have two that I've never used. Another that I carried around but never used was a contour gauge.

[@JAGWAC]

You’re so right Jay, sometimes you just have to buy and find out for your self. Appreciate the comment!

[@essentialhandyman]

Really interesting video and one close to my own heart as I'm always thinking of ways to make my work bag lighter. And the best wayt to do that... take stuff out!

[@JAGWAC]

New Developments in this areas, I need to make a follow-up video. Thanks for your comment.

[@bongboyz6468]

I feel like half those tools are applicable for a car because ive definitely used a small mallet, stubby Screwdriver, offset Phillips, needle vice grips etc a few times on cars

[@JAGWAC]

In my personal experience working on dozens and dozens of cars, I haven’t used any of these on them either. Obviously not saying they couldn’t be useful in a “handyman” or “mechanic” situation, just my experience 🤷‍♂️ thanks for the comment 😎

[@bongboyz6468]

@@JAGWAC I should mention i work on German cars. That's probably another factor hahaha

[@gregorymacneil2836]

Other than than the mallet the rest are gadgets rather than tools

[@chingonbass]

I have the same rubber mallet, I use the crap out of that thing