Your video is very helpful for me bundle of thanks I waste many days on this 😊😊😊
@Pak.Artisan2 жыл бұрын
Bro, help me i attached all wires as you did in vdeo but its brightness was too dull and then i attached A and K to 5V and GND then it got too bright please help mee
@kamalmka92752 жыл бұрын
add a potentiometer between 5 volt and A and K
@Pak.Artisan2 жыл бұрын
@@kamalmka9275 Thanks it worked! But you replied too late
@kamalmka92752 жыл бұрын
@@Pak.Artisan Oh I'm sorry , but I find this video late.
@kiran_K2 жыл бұрын
First after the code run there is print text with no light in screen, after this I joined to A and K , Then there is light in screen but no text. What should I do
@ikissbass696910 ай бұрын
Try adjusting the potentiometer, should work!
@tihamkhan8443 жыл бұрын
Bro can u help me with these messages from arduino avrdude: stk500v2_ReceiveMessage(): timeout avrdude: ser_send(): write error: sorry no info avail avrdude: stk500_send(): failed to send command to serial port avrdude: ser_recv(): read error: The handle is invalid. Does it mean that I am not receiving any command
@AryanSingh-v6d3 ай бұрын
bahut badiya guruuuuuuu
@tournorthpakistan1223 Жыл бұрын
Thankx that work great
@kamalperuri2732Ай бұрын
Bro , Is it compulsary to use potentiometer while using this type of LCD ?
@shashwatpratap23 күн бұрын
you can use a specific type of resistor but then u cant control the contrast,1k to 10k is recommended
@ymautomation39833 жыл бұрын
Nice video thanks sir g
@globalspyhawk34293 жыл бұрын
thank you
@Insha9392 жыл бұрын
Continue bro
@043adibdzakwan2 Жыл бұрын
idk what are you talking, but i know what you mean. thanks brother
@manchikatlasaipraneeth1327 Жыл бұрын
This one Worked....🤝
@Stahl_und_Eisen Жыл бұрын
Yabadabadoo the title is in english, the video should be too
@tarunicab73766 ай бұрын
Thanks a lot it worked
@FaiqSajid-g3e10 ай бұрын
Bro soldering is necessary ?
@VaidikKhurana9 ай бұрын
no, but it is recommended the lcd may glitch sometimes that is not permanent however.
@karimullahsheikh2672 жыл бұрын
My LCD do not show antything, but it turn on. I've Tried everything.
@Jean-xs5km4 ай бұрын
same did you solve the issue
@Shantanu-p5y9 күн бұрын
Soldering issue maybe
@abduldaim4 жыл бұрын
Interesting video
@globalspyhawk34294 жыл бұрын
thanks
@Mystical-TEDDY_2 жыл бұрын
Is there a way to do this on an ESP32?
@julianpierrebalaba388218 күн бұрын
bruh why my lcd is not working.... huhuhu
@codessolution5 ай бұрын
Kia already coded lcd kay code hum edit kar saktay hain?
@shashwatpratap23 күн бұрын
yes
@ThatOneCodeGuy_Minecraft11 ай бұрын
my text says b̵͚̟̉́̉̾̓̀̋͜l̶̛̜̞̼̹̗̤͚̥̠͙͎͓̫̼̹͍̜̫̺̓̓̊͂̓̆̀́̉́̕͜͝͠͠ḅ̸͉̱̣͚̖͖͈͈̜̣͕̼̥̈́̽͒̾̐͗̑̄͒̏̍͒̄̽͜ļ̴͉͚̞̲̝̭͇̪̖̹͔͈̙̝̗̑ͅͅb̵̢̗͚̪̜̳̖̼̝̝̫́̈́͂̃̍͂̂͒̾̍̋̍̂͛̌̀͌̉͘͝͝͠ļ̴̨͙̜̜̤̹̖̟͓̙͈̠͙̟͙͓̬̺̪̥̇͗́͛̋̉̍̓̎̋͐̓̏̓̿̇̏͝͝͝ͅ
@shashwatpratap23 күн бұрын
check for data pins and proper soldering
@shineetejol6 ай бұрын
My lcd still not displaying anything
@azuraxxv3 жыл бұрын
My LCD Is not working. I've Tried everything 😥
@globalspyhawk34293 жыл бұрын
is the light turning ON ?
@azuraxxv3 жыл бұрын
@@globalspyhawk3429 No its not :(, I''ve tried potentiometer, grounded contrast pin and nothing worked
@globalspyhawk34293 жыл бұрын
ok, connect 5v of arduino with pin 15 (pin A) and GND of arduino with pin 16 (pin k) and tell me if the led light is turning ON.
@globalspyhawk34293 жыл бұрын
There maybe a problem with soldering. I also faced the same problem so i soldered it again, but in my case the led was turning ON but there was no display.
@azuraxxv3 жыл бұрын
@@globalspyhawk3429 No it wont turn on :/
@rinkusanuofficial64682 жыл бұрын
Sir ye lcd kaha milega jarur bataiyega sir ji
@globalspyhawk34292 жыл бұрын
kisi bhi online store pe search kare "16x2 lcd".
@Mr__Teja__6 ай бұрын
Hello bro I need ur help
@GWorxOz3 ай бұрын
Gibberish.
@azeromerika217810 ай бұрын
ne radi bogam
@Ronaldo-em5ky4 ай бұрын
thanks you and justin Gohgalter is the best youtuber 🤮🙄😶🌫