Very nice video,I enjoy watching all of them from you.I would really love to see you troubleshoot main boards as well as you do power boards.
@MrReeceyburger1238 жыл бұрын
Cheers buddy, I have done in the past theres a couple of videos on my channel :)
@MasterMindmars Жыл бұрын
So. One only little capacitor SMD shortcircuited was the whole problem? My mama!!! Spend lot of hours to find it. I hope it deserve the work. Congratulations. Thanks
@MrReeceyburger123 Жыл бұрын
Thanks man nice one.
@irishguy2000079 ай бұрын
Please, do you have the pinout for the connector to the power supply board? I cannot get any information on this. I would like to know which pins are ps_on, bl_on etc.
@seksualusis2 жыл бұрын
As to C525, I came today across notion, that this ceramic cap can be replaced by 47uF 100V electrolyte. You find space provided for it on the other side, marked C521. Both ceramics (similar third one, too) are reported as frequent to fail. Thanks for your lesson!
@saarike7 жыл бұрын
That was very difficult failure! Nice work.
@MrReeceyburger1237 жыл бұрын
Cheers :D
@collegge423 Жыл бұрын
Really good informative video's..I have the same board on a jvc led tv..but have no standby led..can you point me as to where the problem could be...thanks
@alexmihai225 жыл бұрын
Hy, what should be the voltage output normally for a Telefunken T39FX182DLP 39"? I put there 167V through a 4.7K resistor, but I've got 167V on the LEDs despite that resistor being in series with the LEDs, I tried then with 100ohm and with no resistor and the backlight is the same, barely lighted. I want to sweep that board for a different one, with a simple design that I have, but I need to know the voltage.
@shauntaylor91448 жыл бұрын
hi fella fantastic video m8, i fix tvs for a hobby love doing it, i've got a polaroid, p40led14, with no backlight i've tested the red wire 117 volts coming off it and stays there, but at this voltage does it like one of the leds has shorted, thanks for your time,
@MrReeceyburger1238 жыл бұрын
Hi mate thanks for the comment, if its stuck at 117 volts the driver chip MP chip as shown in the video is normally the cause.
@davidpringlepatrick42624 жыл бұрын
hello reecey, cheerrs for videos and all you do but have yet to find a fix for same model except all works great and then backlight goes out after 3 mins, only way to correct is to turn off and then on again, but same issue after 3 mins. My question is, surely this cant be a backlight issue if all working great then cutting off every 3 seconds??? sound is on all the time. What is telling the backlight to cut off??
@96thelycan Жыл бұрын
Damn, mine needs a new led control chip, maybe the same as yours but I'm not sure
@antoniogoncalvesb.pereirag89223 жыл бұрын
Hi I’ve I’m in process of fixing my VESTEL board it’s for a 55 inchs Samsung model 17ips20 board number 071114 R9.. Total led strips 12 . An got 7 leds on each strip 84 leds in total 3v Each . They are driven by 4 wires feds on the power board 2 for each set of 6 strips . I’m getting only 104 v from each fead and getting very low brightness on the leds . Do you know why they are so low and maybe the fault or what’s the leds feads volta output ? Thanks ,
@DerbyRepairs7 жыл бұрын
Hello Reecey! I have the same power supply! After replacing three shorted diodes sb5100 now my tv turns on but after the philiphs logo i hear a wistle sound and the tv turns off and again on and does the same thing. I cheched that all led turns on and they do. Also updated the firmware!I messured the voltage on the output for the led lights and i have 190 in the beggining and 150 later. what could be wrong?
@osoletio7 жыл бұрын
Hi. Thanx for the detailed video!! I have got a 40" with no backlight: There are 125V over the six hughe diodes where 180V are supposed to be. 125V as well on the diode a bit higher on the top right side. Over the hughe cap on the left side there are 380V. So, I have changed the driver MPS3394 and the MOSFET MDD14N25. But there is still no backlight. In regard that the TR300 seems to be driven well with 380V, what else could it be?
@greekfirefighter287 жыл бұрын
osoletio did you find a solution? I have exactly the same symptoms. What should I check?
@jhgplayer14256 жыл бұрын
Hi I have a 17ips20 r6 I get a flash from the backlights when first turned on then black screen the diode to the led fluctuates between 83-85v any ideas thanks
@solarwill78blakey147 жыл бұрын
Hi there just wondering if you could help diagnose my TV witch turns on for a minute lighting up backlights then powering down it has a vestel 17ips20 power supply any help would be much appreciated many thanks
@jamiehandley6 жыл бұрын
Hi Reece, I wondered if you could shed any light on my tv. My backlight works fine when the brightness is dimmed down but when the backlight is turned up it cuts out completely. I am now watching tv with a low brightness screen. Also when a usb device is plugged in - this cuts out the backlight too. Could you help please?
@nn-jp2qd7 жыл бұрын
I've got 17IPS20S that works ok for few hours. But then it switches the backlight off. If I turn the TV off and wait for few minutes I can get backlight again for few seconds and than it turns off. It would be better if it would stay off all the time for the diagnostic purpose. Any ideas about this problem? When it's working I get 167V between chasis and red wire and 25V between chasis and black wire.
@themlotproductions Жыл бұрын
Any idea why there would be variable voltage on the LED output circuit?
@themlotproductions Жыл бұрын
Tested all LEDs and they all illuminate individually. Might there still be a problem with them?
@rafaldobromir82756 жыл бұрын
what is the voltage coming out of the diodes screen? Its 180v?
@irishguy200007 Жыл бұрын
Is there a maximium current that the power supply will allow to the leds and what would be an allowable current??
@MrReeceyburger123 Жыл бұрын
The PSU output is designed for each panel size worth if leds 😁
@irishguy200007 Жыл бұрын
@@MrReeceyburger123 Is there a maximium current these leds can draw above which the driver circuit will shut them down? I read somewhere that there may be a 200ma upper limit which the driver circuit will suddenly role back.
@asv57694 жыл бұрын
Dear Sir, thank you for this video. I have a problem you described at 2:00. After turn on the TV here is a spike of output voltage to about 185V DC but it last 1 or 2 sec, after that it goes to 120V and not 160 as you said. So according to this, LED is failing and power board is most likely OK. Is that true?
@franzjonshon7195 Жыл бұрын
did you manage to fix this? got the same error
@asv5769 Жыл бұрын
@@franzjonshon7195 No, the faulty Tv is sold as parts…
@franzjonshon7195 Жыл бұрын
@@asv5769 damm it, did you check if the leds were ok? i just opened it and found 2 leds not working properly
@Coolboy2775 жыл бұрын
hello mate, thank you very much for the well detailed video and explanation. i have the same board and i think it has the same problem so i have to replace c525 cap but when searched online there are 2 different types of it. 1uF 50V 10% x7R 1206 SMD cap and 1uF 50V 10% x7R 805 SMD cap i believe these are different size of the same cap but can you please confirm which is the one you used ? cheers.
@ManhalV37 жыл бұрын
hello 17IPS19-5P power supply , no back light !!! i check the VCC 24V only ??? please can you help me ?
@danielsaturnino57152 жыл бұрын
Can you just put a resistor on the negative side of the leds to ground for a fixed brightness?
@MrReeceyburger1232 жыл бұрын
I’ll let you have a play with that theory 😉
@izzzzzz62 жыл бұрын
Some good info. I'm looking at a polaroid 49" curved screen. I unplugged the LED's when i turn the screen on it flicks to 200V DC on each of the 2x outputs and then drops slowly down to around 2V dc as the 2x 250V caps discharge with only the multimeter connected. Could it be feedback from the brightness control, perhaps the opto isolator or even the driver fet for the transformer from the switching side to the dc side. Any ideas?
@MrReeceyburger1232 жыл бұрын
Hmm is the 200v there then collapses with the leds in ?
@irishguy200007 Жыл бұрын
What did he use to check the cap, diode mode or resistance mode?
@markholland81523 жыл бұрын
Can I use a backlight boost board to bypass the curcuit
@asssaasssas55556 жыл бұрын
Hi, I have a problem with this power supply. The TV has no backlighting and the voltage on the connector that goes to the LEDs is 65V and not 115V.
@serhiyschur8555 жыл бұрын
The same
@seksualusis2 жыл бұрын
My case exactly. I also have about 300V on big caps, instead of 400V. These ceramic caps are first suspects, if not around.
@guyp35995 жыл бұрын
Hi there. Great videos> Can a 17IPS20 board (same Voltages and screw positions?) be swapped out no matter what makes the TV is? I believe Hitachi, Polaroid and Bush all use this board.
@seksualusis2 жыл бұрын
Check for product codes to match, also if LED connector meets your plug. There are variations out there.
@ilektranastou68837 жыл бұрын
Hy my friend! I have the same board, and i have repair it but the tv not go on ! If you press the on bottom the red Stand by led blinks 4 or 5 times and then nothing happens. The power supply is working and i have 121 Volts on the white connector to the LEDs. and also I have 12v on the black connector! What else can it be ???
@markholland81523 жыл бұрын
Can you help backlight goes off after some time charged power supply charged motherboard can it be a led
@vladimirafanasiev68156 жыл бұрын
Hey. do not tell me that the mosfet is on the position of q505?
@cptcabbage2 жыл бұрын
I'm getting getting crackling on power but no power led... no back-light at all. Capacitors all look fine. Any ideas?
@cptcabbage2 жыл бұрын
Its the board without the row of diodes.
@MrReeceyburger1232 жыл бұрын
Sounds like a short on the board somewhere. You need a DMM to test, power disconnected.
@leewright61015 жыл бұрын
REECE dont forget you changed mainboard so actual time of tv use is not correct , as mainboard was replaced,
@constantinjitariu14393 жыл бұрын
I have the same PSU but it is clicking like a clock continuously what can be the problem?
@nickjones8864 жыл бұрын
Glad I found your video, I've the same issue, no backlight. I have just under 160v on LED+, changed the backlight driver IC, at startup, backlight flashes just enough to see boot picture. So, I guess it's shutting LED drive down, would I get this if some LED have failed?
@seksualusis2 жыл бұрын
I guess picture wouldn't come at all. Most likely power supply at the issue.
@nickjones8862 жыл бұрын
This repair was some time ago@@seksualusisI think the issue was burnt out LED's which killed the original backlight driver, I fixed that then it fired up but because the wring current was flowing it shut down.. Then I trashed the TV by cracking the panel but I fixed the back lights!!! I then purchased a backlight tester and used it fixing another TV that ended in disaster, got lightening damaged psu PCB, replaced that with one of millions found on eBay, fired it up, no backlight.. Seller said, oh yes, it'll be your backlight, checked them, nothing wrong with backlight, all lit up same brightness then... Cracked screen putting it back together... Damn TV repairs.. Got a refund but was really cheesed off destroying what would have been a cheap repair.
@seksualusis2 жыл бұрын
@@nickjones886 Still fighting mine. It has no base operation voltages (like 12V for mainboard), but has 300V from rectifier/PFC. The problem is, it is quite crappy design, scheme shows elements that are not actually present, and in current situation complicated to discover what is at the failure, as it is chicken/egg, not something sequential. May have to learn in detail how this power switching circuit is supposed to operate.
@nmocruz7 жыл бұрын
There is a few models using the referebce 17IPS20. My 55ao2usb is compatible with 17IPS20 taken from other models ? The tv is shutting down the ledpanel after some heavy work like, 3D movies from PC HDMI, and one or 3 times using the internet. I want to replace, but I dont know If a can use any 17IPS20
@MrReeceyburger1237 жыл бұрын
Replace the mainboard if its turning off randomly.
@nmocruz7 жыл бұрын
It can stand days weeks without shutdown just the screen (sound continue play), but when I connect the PC+HDMI to see 3D movies, the tv only can take some ~30min, then I need to turn off and on again in the remote, and everthing is ok
@MrReeceyburger1237 жыл бұрын
Replace the mainboard.
@EddySchwertzigHightechactus5 жыл бұрын
Hello, I have the same problem and the same card. I wanted to know what should be the output voltage at the connector CN501 (connector that powers the LEDs)? I have 100V, so is it the right voltage and is it the LEDs that are dead or not? Thank you.
@seksualusis2 жыл бұрын
One might check first, if he has about 400V on big caps, as measured here. If it is way lower, this may involve earlier stage, just like it was suggested. Even though this earlier turned to be caused by short at the end, being connected.
@dandimond36858 жыл бұрын
where did you get your mps3349 chips from? I have a vestel 17ips20 in the back of my TV and its measuring at 120volts I assume its that chip that has gone down. need to find out where to buy. cheers
@MrReeceyburger1238 жыл бұрын
Hi mate I got the chip off an ebay seller called Tekkid he sells them for a good price.
@dandimond36858 жыл бұрын
+MrReeceyburger123 I can't seem to find him on eBay. the chip I have is mps1333 could you find a link and post it please. thanks. dan
@MrReeceyburger1238 жыл бұрын
Hes sold out thats why just checked :L
@salvax164 жыл бұрын
unfortunately it is not always so easy my card seems all ok but no led I also changed ic mp3394s but nothing always in protection! changed the mosfet but nothing
@greekfirefighter287 жыл бұрын
I have the same psu problem, but I have 120volts steady on the six diodes and 380volts on the left cap.Also I hear a strange sound coming from the pcb.Any idea?
@MrReeceyburger1237 жыл бұрын
What you tested ?
@greekfirefighter287 жыл бұрын
I have change MP3394S controler,I have checked all mosfets Q301,Q211,Q100,Q502,Q101, are OK ,all diodes are ok.C525 OK, C127 OK.
@JoseA-Divergent7 ай бұрын
Siempre los putos C , Diodos y MosFet -N y menos paro tambien una Resistencia en el circuito de Hig ...... Saludos.
@maniatore20065 жыл бұрын
MY Vestel 17IPS20 is for an 40" TV and has the issues that i have no 100v on the output for the Backlight. but who can i find the Schematics for this. The backlight turns on for under one second. After i turn on the TV
hi mate i have a 17ips20 power supply and also have no backlight, if one led goes out will it prevent the others working?. tia
@MrReeceyburger1237 жыл бұрын
Yes.
@kefkenliqerim5 жыл бұрын
Hi my TV voice works but not video. What is the problem?
@Samianas2304 жыл бұрын
I got positive to negative 0 in led output, but positive to chasey its 157v. What could be wrong?
@MrReeceyburger1234 жыл бұрын
Samianas230 just find out for yourself
@seksualusis2 жыл бұрын
Negative
@plantas75405 жыл бұрын
EN ESPAÑA DECIMOS...TE MUEVES MAS ..QUE LA COMPRESA DE UNA COJA ..JAJAJAJAJA UFFF ME HAS PUESTO DE LOS NERVIOS
@harveyhyke81657 жыл бұрын
forget all that if the drive is overloaded with too much white lite put 300 ohm resister in line with the positive
@cathybradberry5108 жыл бұрын
got a jvc tv with a 17IPS20 board , powers on but picture is faint , what is the problem please
@MrReeceyburger1237 жыл бұрын
Hello please post on badcaps.net I will help there.
@johntda5 жыл бұрын
I to every one, I have a 171PS20 and C312 is missing , does any one no the value of it please. The cap is across Q301 on the big black heat sink, just it`s pin`s there.
@reacey10 ай бұрын
Red is negative on these vestels on the backlight connector ..daft
@irishguy20000711 ай бұрын
What size tv is this?
@MrReeceyburger12311 ай бұрын
40"
@irishguy20000711 ай бұрын
@@MrReeceyburger123 Ah I have the exact same board and 40 inch panel. What is a typical current draw from these leds?. I have used an external power supply and the leds are drawing 150ma, is that normal?
@paulredmond59564 жыл бұрын
That's completely different to the 17IPS20 board in my tv mine doesn't have those 6 diodes and before you say mine must be the p version it's not
@peterkoz65084 жыл бұрын
Please tell me: what is value of capacity of this C127?
@bentleebriar75403 жыл бұрын
i realize it's quite off topic but does anybody know a good place to stream newly released tv shows online ?
@rylancarl47703 жыл бұрын
@Bentlee Briar Try Flixzone. Just google for it :)
@musaalonso31193 жыл бұрын
@Bentlee Briar I would suggest FlixZone. You can find it by googling =)
@johntda5 жыл бұрын
I to every one, I have a 171PS20 and C312 is missing , does any one no the value of it please.
@tdomingues898 жыл бұрын
thanks!
@MrReeceyburger1238 жыл бұрын
No worries :)
@XheadfirstintoawallX8 жыл бұрын
5:47 i just blew out the tv with that :(
@MrReeceyburger1237 жыл бұрын
:(
@craigfulton33167 жыл бұрын
whare do i get a mp3994s mate
@craigfulton33167 жыл бұрын
or MPs 1344
@harveyhyke81657 жыл бұрын
but ime not saying ignore video as its good but a quick fix 300 ohm