18650 Battery Charger - TP4056

This time I am making a charger for my 18650 Batteries. It is a simple design that you can easily prepare at your home. For this project I have used a 5V 2.4A charger (iPad charger), if you are not considering about the time to charge your batteries you can also go with lower current charger with minimum 1A of current. Increasing the current will decrease the time for charging the 18650 Batteries.
Materials:
1) 18650 Battery Case/Holder x1
2) TP4056 Charger Module x4 - ebay.to/2JzABd8
3) Copper wires
4) Acrylic Sheet
5) PCB holder/Spacers x4
6) Screw nut x4
7) 5V Charger 1A or above
Thank you.
Subscribe for more future creative project videos.
Subscribe Here: bit.ly/2JHtlyc
__________________________________________________________________
Song: Culture Code - Make Me Move (feat. Karra) [Tobu Remix] | NCS Release
Music provided by NoCopyrightSounds.
Watch: • Culture Code - Make Me...
Download/Stream: ncs.io/TobuRemixCr

[@drdalewisely]

Excellent video of a fun and useful project. I love that your demonstration is so well done that no verbal instructions are needed.

[@teatime2566]

this is the best one i see

[@parthipanparthipan3308]

Super bro good very very thankful.

[@ganatp]

Excellent 👍👍👍

[@saaqisms]

Classic idea and superb assembling bravo.

[@sheva9127]

Надо мощнее блок питания. Каждый модуль 1А выдает. Соответственно зарядку нужно брать минимум 4А, в идеале не менее 5А.

[@alexbup4025]

12 вольт?

[@sheva9127]

@@alexbup4025 5 вольт 4 ампера. Слабая зарядка может не вывезти такую нагрузку.

[@alexandertinkov2960]

Надо на каждую плату отдельный зарядник. Тогда все это дело попрет. Нада делать аккомуляторное помещение. Как на производстве.

[@johnmcgrath8673]

I get this design with individual cell management. Much better for battery life and safety. The question is how to integrate this into a rechargeable device? So you charge each cell at 3.7-4.2V, but what if the load is the 4 cells in series requiring 14.8 volts? Do you need to create an isolation circuit or relay?

[@freenergymax]

it's parallel, good

[@Midnight9909]

There are special chargers for this. For 12V there are specialized boards with balancing. Type 3S1P

[@technicalsohil4063]

​@@freenergymax parralrl worth

[@АндрейГерасимов-м3ь]

Congratulations. Cheap and good solution for any number of modules you need in. Clearly visible charging of each battery. If one of the modules fails, it will be immediately visible. For quick charging 4x18650 is better to use 4x5Vx2A=40W power supply unit. Goog luck!

[@LahisTechLT]

Thank you. Appreciate your support.

[@Dhinkachika989]

@@LahisTechLT hello bro Which thing drops in Ampere or voltage ?

[@juliosaavedra1969]

The module does not allow fast charging...it only supports 1 amp. For fast charging it would have to be 3 modules in parallel for a single battery... if the charger is 5v. 2 amp. and the 3000 milliamp battery... it took 6 hours to charge all the batteries.

[@juliosaavedra1969]

The module does not allow fast charging...it only supports 1 amp. For fast charging it would have to be 3 modules in parallel for a single battery... if the charger is 5v. 2 amp. and the 3000 milliamp battery... it took 6 hours to charge all the batteries.

[@teachinghouse2821]

Excellent video I have found. Appriciated

[@masgennady]

Дружище, у тебя получилось классное зарядное устройство! Надо было ещё написать: - какое сечение провода ты используешь... Думаю, что если использовать зарядное устройство 5V, 1A, зарядка аккумуляторов будет дольше, но модули не будут сильно нагреваться... Лично от меня - нравится, уважение и подписка! Пламенный привет из Российской Федерации!

[@СергейСергеевич-ь9щ7к]

я спаял такую же систему , и у меня от перегрева отпаялся с платы штекер ,,,, собирал как на видео. в итоге заказал на АлиЭкспресс десяток ТП 4056 и подключил каждую через блок питания от компа , вот только тогда заработало всё , и ничего не греется.

[@ru73rr]

@@СергейСергеевич-ь9щ7к Потому что суммарный ток 4-х аккумуляторов при зарядке 4А. На видео у него ничего не расплавилось, потому что аккумуляторы были почти заряжены.

[@Midnight9909]

Ладно, убедил 😉 За идею в тяжёлых условиях 👍

[@taunteratwill1787]

Your drilling has the precision of a blind man. :-))

[@LahisTechLT]

Haha LOL!

[@rw4pjqradiomaster529]

Отличная идея. Просто и доступно. 👍

[@ru73rr]

Ага. Особенно подключить это всё к зарядке на 2А.

[@rw4pjqradiomaster529]

@@ru73rr или к 0.5 А

[@ВатникКолорадский-к5с]

@@ru73rr Два Мгера - сила!!!

[@prasadpkamath]

Thank you for the useful information.

[@ВалерийБеликов-щ1н]

Cool my friend... Cool.

[@Pzapza]

Nice video! A question though....you used a 2.4A charger and wrote in the description that you can go for a lower current charger if time isnt an issue...but isnt 2.4A for 4 batteries( 0 .6A per battery) already quite low for a 3000mah battery? I'm new to how chargers and batteries work...so am I missing something here?

[@EFDawahWiseSmile2LanternDen]

it wont charge full 1 amp each battery some batteries ...when they are above 4 volt say 1 battery...it charges with very low current so the other 3 get more current drawn until 4 volts..also i have couple of usb with 2a and 2.4 and most of them i get higher currents almost as high as 3 amp still 4.9 volts on it.

[@nurvius6897]

Perfect .Very nice

[@DIYInventor]

How to charge and Use 18650 battery at the same time?

[@AntonioANT-z7c]

Ciao Lahis Tech. Complimenti. Iscrizione e Like doverosamente fatti. In sostituzione dell'alimentatore 5V 2 o 3 o 4A, si può usare l'uscita 5V dell'alimentatore ATX di un pc, che ha un amperaggio di 15A ? Spero in una tua cortese e competente risposta. Buon Anno. Antonio dall'Italia. (Legnano-Mi)

[@elektron2kim666]

Be careful with making holes like that (breaking a part or not). Use old containers you have around for low cost reasons, maybe some on sale. Poke small holes at first and increase the drill bits for ease as a drill can slip and make scratches otherwise. For wires, buy lamp wire; you don't want too much electrical wire exposed. Use a glue gun for aesthetics or covering things and for firm constructs. Solder 3 times extra than you believe with power delivery otherwise you get disconnects all over. Just advices I try to follow myself. My best power banks are home made. There are many forms of charger circuits for little money. I also find good 18650 batteries as I have a pile of old laptops and I buy a new battery pack instead which releases a few "good enough batteries" and they are fine for a long time. Just forget the bad ones. Those that can't charge any more and they killed a battery pack.

[@camaleon352]

Very very good 👍

[@sed6]

Awesome work, thanks!

[@californiakayaker]

I've had one of these built for years, with about 8 lithiums in series. Was thinking , a balancer would be cool on the same board. But, not necessary because the charger brings up to a specific voltage ?

[@BICIeCOMPUTERconGabriele]

No need for balancing because each cell is charged independently by its own charging circuit.

[@JOSERAFAELMERCADOTIRADO]

Muy buen video,gracias por compartir

[@josehinojosamelo3752]

MUCHAS GRACIAS, MUCHAS BENDICIONES POR MARAVILLOSO VIDEO.

[@cheroviekeithmabini7826]

What type of wire should I use? Is it dangerous to use a different type of wires? What type of wire is in the video?

[@ВасилийКотенко-й6ш]

Интересные люди. Ну не нравится, не делайте, а то тошните вместо того чтобы поблагодарить парня за проделанную работу. Он вам предоставил как вариант , а хотите делайте, хотите забейте. Ведь когда вы заболеваете , сразу же не вешаетесь. Так и здесь ситуация, возможно и поможет эта процедура. А продавцам похер на вас , они таких и ждут которые не пытаются,не борятся и не стемятся. А то что вы называете фирменный,классный акб, то и здесь не исключено что попадёте на фуфло. А на счёт этого восстановления, так моему тестю в эл.велике 36/10а делали точно также . Он рад безмерно. Дошло до того что он доезжал на дачу и ставал на зарядку так как назад не хватало заряда. После балансировки он теперь может преодолеть три этих расстояния и при том что и гружоный. Так что вместо того чтобы травить тюльку сначала нада попробывать. И в любом случае поблагодарить человека что дал вам вариант попробовать, поэксперементировать.

[@Kurooks]

if want to give a load, for example LED, the LED is paired with 1 tp4056 module or are all connected?

[@hanj1240]

Without bms?

[@pethani11]

TP4056 charging module me BMS ki jarurat padegi? ya is module me hi BMS Diya Gaya hai?? Please reply 😊

[@techtechnicalgaming]

Tp4056 module is available in both with bms and without bms version

[@summerWTFE]

Great inspiration and well executed.

[@PraveenKumar-gn3em]

what about output in this circuit, it is posible to take output in same circuit

[@rich1051414]

That solid core wire is overkill for 1 charging amp per module.

[@rich1051414]

@@sociretbarreto4991 ¿Qué?

[@mwint1982]

I think it's an old wire coat hanger his mother beats him with. He is happy to rid her of it. No more crying, only tears of joy!

[@rich1051414]

@@mwint1982 Funny, but it looks like household electrical wire :)

[@mwint1982]

@@rich1051414 his mother makes the hangers out of 10 3 Romex

[@leandroyumol4882]

It's a wire of an outdoor antenna

[@nhobuiquangngoc2760]

I bought copper wire with a diameter of 1mm but I solder without stick. As in your video, what diameter is the copper wire and what diameter should I buy again for soldering like you

[@jaybalbuena5045]

how many hours does the battery needs to be fully charged by tp4056?

[@srvshkmr336]

Not a good idea because the current limit of 1amp will be exceeded while using charging 1 and 2 cell in a 4 cell setup and the chip will smoke. Some kind of current limiting arrangement should be used to limit 1 amp current to each of the 4 modulea in the setup.

[@nurvius6897]

Thank you

[@genridiuk7402]

молодец мужик всё просто и понятно тоже так хочу

[@taufikhidayatullah9420]

How about output can parralel?

[@Alwaysdoubt100]

Couldnt you have used Just one board to charge ALL 4 batteries?

[@RA-mi8hk]

Shall i connect 2 battery in parallel and charge using single tp4056 module.. It is possible or not. Any problem occur in battery or not

[@flaxlsm]

Since you're connecting the batteries in parallel, that should not be a problem (given the batteries are of the same starting voltage before connecting). But by doing that, you'll have to wait ~2x longer than just charging 1 battery.

[@maatiraouki9124]

excellent

[@enrgysolarandpowerinverter4379]

Question: Can I connect two bms 24 to get 48 volts using one charger, thank you

[@juliosaavedra1969]

The module does not allow fast charging...it only supports 1 amp. For fast charging it would have to be 3 modules in parallel for a single battery... if the charger is 5v. 2 amp. and the 3000 milliamp battery... it took 6 hours to charge all the batteries.

[@rivenmain2175]

i dint understand 4.2v is fully charged so if it keeps charging for 35 minutes it ruined the battery

[@funkiEst]

Does the charging circuit incorporate some inverse polarity protection ... just in case ? thanks :D

[@koleso3651]

нет

[@mohamednour1645]

Thank you very much In the same way can I make them 8 or 10 battries and charge them with the same charger (1 charger for the whole 8 or 10) In the same battern Thanks again and grettings from RGYPT

[@dimensitybg]

Is it possible to use 2 18650 charger module boards to fast charge a 18650 battery?

[@arielelijah1282]

Hi is it okay to use two 18650 battery on a parallel circuit with 1s bms (4mos bms) on this charger?

[@joeldubus2362]

hello what is the size of the rigid electric wire that passes through the card? thank you

[@jyotirani8232]

Nice

[@ahmetermis5413]

Aynisini yaptim hatta 15 adet pil sarjlisi akimi voltajida sabitledim elimde 15 ten 5 adet modul kaldi bir bir yaniyor neden acaba

[@namangupta86]

Make a powerbank on this design as well. Nice and easy.

[@LahisTechLT]

Yes, Thank you

[@namangupta86]

@@LahisTechLT It would be good if the power bank would be able to pull out QC 3 as well. Waiting for such a video ASAP. Thanks!

[@LahisTechLT]

@@namangupta86 sure i will make one in near future. Thank you

[@stargazer2428]

I make that too but the module hot while charge the temp maybe 60-65 is it safe that hot?

[@juliosaavedra1969]

The charger has to be 5v 4 amp. each module supports 1 amp...

[@prathammohite8118]

How many lithium battery can charge in one module but on same charging part witch you have made ❓ please I need your answer

[@shahriarahamed2740]

At highest two, but i recommend to charge one at a time, it makes the battery health stay good

[@kartikey5305]

@@shahriarahamed2740 why only 2 , can't i charge 5 batteries ?

[@TheRealFobican]

What happens if I try using a charging module meant for lithium ion batteries to charge lipo batteries instead?

[@mathiasbekker211]

They’re compatible

[@TheRealFobican]

@@mathiasbekker211 how much?

[@mathiasbekker211]

@@TheRealFobican a lot

[@rotho282]

Nice idea! The music on the video made me want to claw my eyes out though

[@LahisTechLT]

Thanks

[@mikebond6328]

Why would you do that? You could still hear the music.

[@GG-xt1hh]

Hi, what dimensions does acrylic have?

[@kartiksuyash]

Superb

[@janryansantos8473]

Hi how to add single output or discharge .. 4 parallel battery

[@dguns66]

What is the voltage? I am trying to do the same thing but with three batteries. And then I want to get the output voltage to be 9V. But when I put the Output voltages in series, I only get 3.7V.

[@ernestosabado5712]

I did quite the same charger but 2 X16 celles

[@ernestosabado5712]

Why not to insert diodes to prevent burning the tp4056 from cell inversion?

[@GabrielKozsar]

I did it differently a little bit. I drilled 2mm holes on each side in the battery holder to run the + wire through the corner of each cell. Then soldered the wire directly onto the pcb. Drop of cyanoakrylate glue to hold the wire in place , or hotglue, inside the holder. This way the back of the acrylic is flat , i.e. no wires. Alternatively a copper tape/strip on the back side for bus bars and solder a small wire to it.

[@Alhast72]

Гений!🧠👍👍

[@nutagrigore2032]

Hi there. Can i connect 2 usb power supply? for example 2X500 ma one in each port?

[@LahisTechLT]

Yes

[@vk912399]

My tp 4056charging modules red led never sunt off after I charged 3hours, 🙏plz tal me why it's countnusely charge and never stop with 2000mah lithium battery??

[@whitelion61]

What would happen if I were to plug in multiple power supplies? Would it charge faster or could it even cause damage?

[@LahisTechLT]

Since TP4056s are inter connected go with a one power supply

[@ninosantiago3.143]

*Te quedo perron ese cargador amigo te ganaste el Like* 💥👈

[@frankstocker5475]

Nice job.

[@amritswagatadityaraj1111]

Then what is the require of putting more 3 charging module

[@namangupta86]

Every module is capable of charging only 1 battery. So 1 module for every battery is needed. Although I feel it would have been better to make a powerbank instead which would have both capabilities.

[@marcrobert5593]

@@namangupta86 no, you can just put all the 18650cells in parralel. A balance charger is only required when you run them in series.

[@leandroyumol4882]

Will my regular android phone charger charges this? 5v 2.4a, and how fast?

[@miteshdhanani]

As u r showing we r doing the same way but the battery does not charge the whole day it’s kept in the sun

[@northbound201]

What gauge wire did you use

[@AnkylosSpondylos]

i have a question. if we wiring 4 tp4056 outputs in paralel, can we use it with safe?

[@azuolasv]

Hey , i was wondering if you can charge batteries with 1 charging module?

[@saranke9802]

You need 30min x4 = 120min to get full charge

[@miteshdhanani]

How can we connect it a 3W6v solar panel

[@deskonect]

Nice job...👌

[@electroumit]

You need min 5V 4A power supply and 9v alkaline battery for multimeter.

[@Chegewaro1988]

Спасибо.

[@manojmishra9183]

सर जी नमस्कार।क्या 1 मोड्यूल सर्किट से चारो बैटरी चार्ज नही हो सकती है कृपया जानकारी दे या चार बैट्री के लिए चार मॉड्यूल ही लगाना पड़ेंगे।

[@mn_story]

Buatlah 1 lagi dengan saklar

[@ИльяКК-г4ц]

Сколько по времени полный заряд?

[@patideb]

Please tell me the price of those 3000mah cells

[@kmuralikrishna1582]

Fine used 5V 2.4A but actually required for each cell or each TP4056 board required volts and amps ..?

[@LahisTechLT]

5V 1A

[@Davysguru]

@@LahisTechLT so 5v 4amp charger is required???

[@LahisTechLT]

@@Davysguru yes

[@ensardemirkol4361]

Is it possible to make this project with just one TP4056?

[@Peatex]

Yes it’s possible

[@lazlogurzogonas878]

this charge can handle 2 wires flat li-on (3,7 V, 2500 mAh) battery (used in drones, tablests, etc)??

[@LahisTechLT]

Yup any Li-ion battery under 4V.

[@noobmaster6074]

Awesome

[@asadpatel777]

Whts the price of batteries?

[@FoodsecretsJahangir]

Learn how to use the DC volt and amp Meter in this project as well

[@3aieTs_2]

Только лучше 4 зарядки и не паралелить их. Будет быстрее заряжаться. А то так 2 ампер будет заряжать 2,5х4=10 ампер примерно 6 часов. И сама зарядка хоть бы месяц протянула с полной нагрузкой.

[@rubenhayastan4854]

можно подключить лабораторный блок питания ,если даже на 2 А ,так,как акб заряжать надо по 500мА ,так ,что спокойно 4 акб зарядит .

[@3aieTs_2]

@@rubenhayastan4854 Ну так зарядит, только 2500/500=5 часов, а с потерями все 6 часов получится, вот о чем речь. А в 4 раза мощнее за 1,5 часа зарядит, к чему мы обычно уже привыкли - зарядка 1-2 часа

[@soylibre]

how can i connect a solar panel to charge and what the capacity of the panels needed

[@kailashupreti3081]

The USB cable provides 1.5 amp, 5volt current to the Module which then charges the lithium cells. So any solar panel with a output above 5 volt in series with a 5 volt regulator with do the job

[@borisloncar3011]

The TP 4056 for 18650 battery in addition to the Micro connector for charger connection has + and - terminals for connecting the battery. Watch the video carefully when it comes to 0:21 you see that the man has brought 4 TP4056 modules closer to the camera and you will see that there are + and - contacts next to the Micro connector to connect the solar panel.

[@FoodsecretsJahangir]

So that we can find out how much our 18650 battery is charging

[@LahisTechLT]

Jahangir tv yeah i will make one in future. have to purchase those parts.

[@FoodsecretsJahangir]

@@LahisTechLT thanks so moch I m waiting 4 your video this project

[@InnovationTech]

I have 7800 mah 18650 batt so why do you have only 300mah

[@stasbz]

Why does it take so small time to charge?

[@RizwanSaeed]

from where the cells are purchased?

[@VesExcYohannes]

Diagram 4:30

[@w.t.2905]

Output adapter 2.4 A ???? Are you crazy?

[@sayatau1911]

😮four now save or not..? I wont charge aa baterai.

[@ihsancihan9386]

thx