Lithium Battery Charging Station

[@Magneticitist]

People are so critical but this is literally a cheap and easy solution to charging which is done more or less the same exact way in common electronics using lithium cells. I've used these modules many times and they work just fine for being so inexpensive. Whether it's a circuit pull or a bought module it's all about the same tier of charging circuitry. Some modules can be adjusted via board resistors so the cutoff is more suitable for higher or lower capacity but one module per 18650 cell is good at 1A. In the absence of a 5V 5A supply, buck modules are also cheap enough to implement for use with inputs like laptop chargers. If people wanted to get 'extra' with it they could also add 4 individual digital voltage display modules which are also inexpensive, as well as a quality USB output module on one or all of the cells for use from battery only. I've noticed with a lot of those charging modules they also implement some form of safety in that they will not attempt to push more than 100mA or so into a 'dangerously' low cell until the voltage has risen enough over time. TP4056 is easy enough to find for cheap on ebay.

[@DavidGillooly]

Nice idea on using the standoff/connection pins.

[@paolomichielin3039]

Mi piace questo progetto ! Semplice da fare e molto ordinato nell' assemblaggio ! Bravo!!!!!

[@sushantamondal5162]

A

[@michkx9173]

Un' italiano!!!

[@howtocreate7413]

احسن طريقة لشحن بطارية الليثيوم kzbin.info/www/bejne/aWLNp3WLZ5mbqqc

[@artistnikhilbhavsar5766]

Is it cheaper then ready made?

[@easytechzones]

yes

[@swapnamoyhazra6036]

Of course

[@conesillyvalley7182]

Good workmanship, you should type the charger model number TP4056 Also mark + on battery holder because li-ion batteries have no polarity written on it

[@AsifHussain-rk7cn]

😂🎉

[@apptest1471]

The TP4056 module is designed to charge a single 3.7V lithium battery at a time. It provides a safe charging current (typically 1A) and has overcharge, over-discharge, and short-circuit protection for one battery. with longer charging times, you can use one TP4056 module to charge the four batteries in parallel. However, for better safety and charging efficiency, it's recommended to use four separate TP4056 modules, especially if the batteries are not perfectly balanced.

[@sreekumarUSA]

Good video. I’m actually keen to know about the small electric drill that you made. Where did you get the Chuck from? Is the length of the motor spindle long enough to accept the chuck? Please let me know. Thanks.

[@easytechzones]

From electronics market

[@sreekumarUSA]

Thanks. I know those can be bought and assembled from an Electronics Market, as you say. But need to know what Electronics Market, where is it available and a link to point the Electronics Market. Is it from Ali Express or Bang-good? Please let me know from where you bough it. Thanks and best wishes.

[@michaelgasperik4319]

I get my parts from the Geek app. It's part of Wish and most of the items ship from China. So delivery to the US is typically 6 to 8 weeks. I think you'll like 4PCS Micro Motor Drill Chucks Clamping 0.3-4mm Taper Mounted Drill Chuck With Chuck Key 3.17mm Brass. geek.wish.com/share/4713kzlmtd You can actually get everything from this video from there, charge modules, pin headers, cell holders, project box, even wire if you need it.

[@jyotirani8232]

@@easytechzones Delhi me milega kya. kon se market, or shop number?

[@kushalbhaskar4401]

All the parts are available at Amazon.....

[@abdulwahid8579]

Great job with all the best information and knowledge

[@arslansattar351]

Now switch it on a transformer charger board for every device ready for you with wires.....thumb minus finger plus.......

[@Trustedtui]

what volt adapter you use? 12v 5A?

[@pukhrajdeepsingh3629]

Bhai agr isi 3 battrey mai se se output lena hai 12v to le sakte plz bata do

[@Didi-rl9is]

Thanks verry amazing very exellent.good ideas

[@easytechzones]

Most welcome 😊

[@anuarami7118]

Is it safe to use parallel load output to turn on a 5v fan, thank you.

[@subhajitdatta6370]

A useful video , thanks a lot 🙏 . Alongwith the video , if possible , please provide the links where the parts of the model are available .

[@easytechzones]

You can buy from local elections market

[@pawanelectronics4204]

Ii for

[@dineshipro123]

Nice and knowledgeable video ..... Along with the video , if possible , please provide the links where the parts of the model are available .

[@shafqatmustafa9166]

Nice and neat work.

[@nec80]

Why do you use 4 charging modules? Would not 1 be enough? Thank you for the video!

[@easytechzones]

No. Because 1module can charge with max 1 amp current. If we use 4 battery it will be take long time. So here we use 4module for 4 amp current

[@michaelgasperik4319]

If you charge more than one cell per charge circuit, it will "finish" charging as soon as the first cell in the group is full. Not only would you have 1 fully charged and 3 partially charged batteries, but you also wouldn't know which one is the full cell verses the undercharged cells.

[@kushalbhaskar4401]

@@michaelgasperik4319 Every module has a overcharge protector, so which ever battery charges first, it stops receiving power....

[@michaelgasperik4319]

@@kushalbhaskar4401 I agree. My comment was in reply to the original question, asked by nec80.

[@nexusryze7878]

I think its better to use 4amp charger to suppy the 4 module.. The current is equally devided on eachmodule on your design so if 1 module can draw out max 1amp current its better to use 4amp supply since 4 modules are in parallel current will be divided less current supplied on a module will increase charging time. Hence the charging time of one battery at a time and 4 at a time will still be the same. But its a nice project congratulation.

[@mumgurung3577]

Nice video bro, brother aap yeh video ko voice ke sath pura dital me bataado plz.

[@abdullahnoman9696]

Awesome, its a very nice idea bro. I like it

[@prakash52kar]

Nice video thinking to replicate, Is there any issue charging the Batteries in Series? By using only one battery charging module?

[@elektron2kim666]

I don't understand the purpose of the box here. It's always better, I guess. Maybe 2 boxes glued together and then hide (on the other side) the charger circuits at least. With some peak windows (some transparent plastic ding-nots) you can see the LEDs. My imaginary version would be to open the charger and have a bigger box. A bottom compartment for the open charger and then the batteries lowered into "second floor" and a lid. The purpose of it would be to transport it on a travel or a move. The top lid could be open when using it and maybe have ventilation and ventilation holes. For beauty, print out a photo of the charger specs and glue the paper on the side of your DIY box with any added info you find cool or informative. Just some ideas... My constructs are horrible and after 4-10 versions it's starting "to be something" and I get better at it over time. Recently I started to construct RC stuff and tiny micro controller "computers" with various parts, so I get more picky than most. A bit of wire management is really practical.

[@jyotirani8232]

nice video sir, agar bol kar video banate to or achha hota.

[@josuetejada5541]

Mamiola

[@josuetejada5541]

Mamiola

[@gunmanih8332]

In parallel setup lipo battery drains 1by1 or together?

[@arslansattar351]

Cutter and plas and screw drive and pack tape make it posible to you......

[@rismaapriliani6920]

Mantap ... Salam dari Indonesia ....

[@shiroumxm2052]

This is what I need for a project, I need 3 batteries and I think that charging them like this is the best option, but I need them in parallel so that they provide the current I need. The idea is that this device remains permanently inside the lamp I am making, but I don't see how to solve that in the end, once they are charged, use them in parallel

[@arslansattar351]

Gd you did it very right my 🦌

[@hermaneduarte265]

Hi, can you use a 5v 2amp power supply if you don’t have a 5v 5amp supply? Would it take longer to charge the batteries or would it be a problem ?

[@easytechzones]

Per module you need 1amp. If you want to charge 4 batteries at a time you need 4amp min but if you want 2 battery at a time then you can use 2amp power supply

[@srikanthdwarapudi]

Already circuit boards had a micro usb ports y ur connect charging adaptor

[@emir.siriner]

Amazing. Very nice. Thanks for share...

[@Mohdasad786_m]

भाई तब रेड बत्ती चलेगी तब किया फुल होगी या को तबीयत ब्लू चलेगी या को होगी या फूलबताओ

[@arslansattar351]

Thumb negitive and index positive with supllies board are these charger to batery devices......

[@MixYourWay]

Well done brother!!

[@archuvel]

Where to buy the battery hold set up

[@dirgajawara1346]

using adaptor or power supply ???

[@sarijuchannel9210]

Use adaptor 5volt ( paralel ) Use Power supply 12volt ( series ) Sorry i cant speak ing

[@masgennady]

My friend, take my very best wishes! Personally from me - like, respect and subscription! Ardent greetings from the Russian Federation!

[@arslansattar351]

Multi functional :-)🙏

[@shamsabraham]

Mere pas variable power supply hai kitna volt aur amp mai set kar ke charge dena chaye ???

[@arslansattar351]

Put wire to driled silicons boards

[@prasadpkamath]

Thank you for the information.

[@ulaganathana8365]

Very very good thanks you so much

[@TheLionaman]

je jo sleeve apne 220v pe use ki hai vo kahan se milta hai plz muje chiye....

[@easytechzones]

Heat shrink tube. Electronics shop mya milega. Online pe vi milega

[@kwkm1]

Nice work

[@SyamAcademy]

How to recharge Li-Po 2 battery set bro?

[@anilkinikar]

Your. videos are good and creative. But I hate these silent charlie chaplin videos of 1920. Speak up in your videos and connect with your viewers.

[@easytechzones]

Ok i will try

[@recepugur2401]

charger module gets heated, doesnt yours?

[@ShebinlalIT]

wow wonderful bro

[@jamilsyed223]

You better explain the steps verbally and also give the names of the components as well. Thanks

[@sharukhmatekuki5830]

Nice 👍🏻👍🏻 🇮🇳 || Kuki 03|02|2022

[@arvindpatil5075]

charging by 5volt batteries connected in parallae is the best way than charging them using in series and bms.because for three battery requie 12.6 volt charger witch is rather difficult to get also each batery is charged by 0.37 %of its current capacity witch is suitable for tp4056 providing 1000ma current.ut for charging more than 2600ma battery this method will work?

[@unsopken0623]

So if ts parallel no need for bms?

[@Doraemon-75]

trokle switch use korte paro best & more professional hobe👍🏻

[@easytechzones]

Nice idea

[@ponvenkat1]

Nice presentation. Thanks

[@KamalKamal-gy8qv]

Pls mention ,provide links Wer we need to buy this accessories link

[@noblesharky3740]

Why you won't post that Product Links in Description??

[@sathyanp.g2000]

Why can't you place the charging modules inside the box. .....nice work

[@a1a2o22]

charging modules and batteries hot during charging mode outside of the box get more cool

[@abdulnazeer6821]

Bhai to konsa diod lagaraha batoto

[@easytechzones]

Kahape?

[@stncontractsolutions6349]

Any idea how I can charge 2x 18650 3.7v batteries connected in parallel? Can I use a single lithium charge module?

[@bikramsarkar2390]

I want to buy the product. Can you please assist me on this

[@easytechzones]

Not available

[@magicalclips3651]

Dear friend is it ok to use 41865 li ion battery in powerbank. Please reply

[@easytechzones]

Ok

[@magicalclips3651]

@@easytechzones thanks a lot

[@Skumar_Rules]

If one or two batteries are fully charged, other batteries are still charging will not charged battery got heat up or bursted?

[@Skumar_Rules]

Ok thanks for your reply

[@boiha1232]

where to buy this battery.. plese tell me

[@mrhkexperiment]

super

[@smnvsinnovations2295]

Good & very useful video...

[@debashishmukherjee3466]

Can I use 5v,5amp transformer ?

[@easytechzones]

Yes

[@easytechzones]

Need to convert in DC

[@debashishmukherjee3466]

Thanks for help.😊😊😊

[@howtomakemoneyonfacebookpa2747]

How many amps output and can it changed 100amps lithium battery. How many amps working current

[@KHOAIHOANG81]

Very Good...!!!

[@MohdWaseem-yr7jn]

Bhai ye drill bhi aapne khud hi banai hai ka, us video ka link send karo please

[@kasturikolla6952]

Bro where we get the plastic box pls tell us

[@mumgurung3577]

Nice video bro but bro aap video voice ke sath banaao, or pure ditall me bataado plz.

[@easytechzones]

Try karta hu. But youtube mya reach hota nehi. Isliye ap logo pas milta nehi

[@nisarzishan800]

Sir your video is very good but you are not explaining is not you are not explain anything that way I am not able to understand anything this video for me not worst

[@ROBZO_GAMING]

nice idea

[@arslansattar351]

Availabilities soon if work go un interupted

[@gorakhtakale8540]

Ye charging module or lithium battery laptop repair shop per milenge

[@easytechzones]

No

[@VishalMast-jb1jt]

4 module ko kitna volt dena padega 🤔

[@dasarisatyasandeep8055]

It is easy to understand if you provide circuit diagram for every vedio

[@DGnumber1]

Nice video

[@tahirqureshitgq7892]

Excellent, thanks.

[@hemantpal4614]

Very nice

[@easytechzones]

Thankyou 🙏

[@Phathomchai]

Block diodes, right?

[@rupindersinghbains9921]

V.Nice

[@easytechzones]

Thankyou

[@ksssaja6994]

For example,there is a battery 3. How can I use only one module

[@mumgurung3577]

Bro., Is me kitne kharch aayega ji saman kitne price me padega ji ????

[@easytechzones]

Approx 700 to 800

[@arslansattar351]

Healer pin in board is the next typical attaching to mother board chargings ......

[@jacklee6539]

Your hands-on skills are too strong, I want you to learn more!

[@nadeemtariq1344]

Very good

[@shakyshakeqs]

can i make this, but i,m using this project to charge my 10 flashlights at the same time

[@palashmondal8117]

Very good project, thanks a lot. Bro I need those circuit board, plz help me

[@arslansattar351]

Zalimo s allah bchay g 😂 sanu paisay walo s allah bchay .....

[@zaheerud-din4146]

Good one

[@shubhamsaurabh8406]

Name of second background music??

[@bhanuprakashap.t8708]

From where can purchase Plastic box?

[@VOLTRONDEFENDER4440]

Use a 4 amp charging module

[@easytechzones]

Oh

[@kumarhero1277]

what is the cost for making this device please mention

[@easytechzones]

Approx 700

[@conesillyvalley7182]

U can buy battery holder (Rs50) and TP4056 charger (Rs30) online from Robu.in , very fast delivery

[@Jatinrohilla18]

You can use only one charging module

[@easytechzones]

If you use 4 battery then take long time for charging

[@khamhtee811]

I use for 2parallel,so I can use type c changer with phone adapter

[@larasresti8734]

Untuk buat rangkaian spt habis biaya brp ?

[@maithiliujanvideo9275]

Super bhai charging

[@JOSERAFAELMERCADOTIRADO]

Hola el cargador de cuantos voltios es?

[@thingsyoudidntknow1745]

Sp there is no pcb that suppprt multiple parallel batery

[@GLENN_3310]

no heat sink / fan ?

[@luckystrike5763]

Kotak na tu beli dmn om