1971 9.5 HP EVINRUDE SPORTWIN - SWEET

[@daniellee9849]

Just got this motor today on a 1963 14ft jon boat. Runs absolutely perfect. Pretty amazing for a 50 year old small engine

[@THISOLDOUTBOARD1]

Hey. Thanks for tuning in. Bulletproof !

[@peteryeung111]

Ya man! It's amazing how, watching outboard motor videos is becoming a new form of education and entertainment for me. Good work.

[@THISOLDOUTBOARD1]

ya mon, tanks mon!

[@williewoodruffjr1609]

Can an extension kit be added to this motor

[@peteryeung111]

willie woodruff jr Late reply, but yes they still sell the gearcase extension for these motors at marineengine.com part#324828. you also need the longer shaft. Ya mon!

[@thetruebrit85]

What a lovely video! Thanks very much indeed for sharing! I've just scored the very same for £50. She is really clean turns over. gear selector clicks into position no worries. She will push my twenty year old Zodiac CFR-350 Nice and bonny. I will of course fit a new impeller and change the lower gear box oil. I wait with eager anticipation.... Going to be excellent taking our 9 Year old grandson along our local canal's etc.

[@THISOLDOUTBOARD1]

Hey. Sounds great ! Thanks again !

[@joeybunkerslgl15gbunker25]

I love those 9.5 I have a 1967 one that is sweet as sugar wouldn't sale it for love or money

[@THISOLDOUTBOARD1]

Hey. Thanks for watching and commenting. Stay tuned !

[@raymercado3650]

Nice rebuild👍 I just a nice ‘73 Jonson 9.5. Only problem is it when you throttle past halfway mark it pauses for couple seconds before kicking on? It also does that when throttle Down from high. Carburetor dirty or timing?

[@THISOLDOUTBOARD1]

Hey. Thanks. What may seem like a fuel issue could be ignition, and vice versa. You'll have to just go through both systems. You'll end up there anyway if you dont get lucky on the first guess! Thanks again & Stay tuned !

[@TheBimmerBarn]

Thanks for the content! Question: Mine runs great with the cover off, but chokes with it on and shuts off. Is that normal? Recently rebuilt carb and used a slightly larger jet, is it running too rich for the cover or can I get more power by drilling larger air holes?

[@THISOLDOUTBOARD1]

Hey. No not normal. Its choking out on exhaust gases, no fresh air. There is a rubber donut type of gasket that will go bad allowing exhaust into the powerhead compartment, and or the exhaust to cylinder gasket is leaking. Numbers 87 & 39. I've seen people cut holes in the hood to allow fresh air but dosent always work. Thanks www.marineengine.com/parts/johnson-evinrude-parts.php?year=1971&hp=9.5&model=9R71R&manufacturer=Johnson&section=Exhaust+Housing

[@TheBimmerBarn]

@@THISOLDOUTBOARD1 This seems like exactly the problem. Thank you for your help and speedy response!

[@jimm1975]

Hey 'this old outboard ' I have a 69 sportwin, I've got some questions I realize this videos five years, having trouble with it idling it was running fine put it in the garage for a couple weeks got it back out to sell it fired it up and it ran like garbage, went through reset the points, re cleaned the carburetor,runs decent at high rpms and mid range low speed,spits/sneezes, adjusted low speed to no avil,is the low speed needle supposed to be sharp on the end? Mine is very pointy/sparp, wrenched on this one more than any other outboard I've ever had! Last one of these I'll ever buy

[@THISOLDOUTBOARD1]

Hey. Thanks for tuning in. Actually this videos is closer to 15 years ago. I uploaded it 5 years ago. Anyway, yes the needle is pointed. Sounds like you've done just about everything. Spits/sneezes is usually a sign of running too lean, or out of sync. Mid & high is good but something is screwing up the idle circuit. Back when, I had 3 or 4 of these things and anytime I had a problem I ended up at Leeroys Ramblings. Don't know if you've heard of him, It's where I learned everything. Check it out the carb section, it may help. www.leeroysramblings.com/OMC_9.5.htm Thanks again & Stay tuned !

[@jimm1975]

Yes I'm familiar with Leroy,so your saying the low speed needle is supposed to be sharp almost like a needle? I've reset points a few times, adjusted the cam timing yesterday but haven't had it back in the barrel yet,I'm stumped,worst outboard I've ever had/worked on!! Didn't realize the video was that old ,but you always seem to get er done,hate reaching out to people but ya know sometimes you have to, thanks again for your help, Jim

[@dashingdzolihoidzo8579]

what speed does the motor develop on the boat ?

[@dashingdzolihoidzo8579]

km.

[@THISOLDOUTBOARD1]

Hey. Thanks for tuning in. The 9.5's would average 17-18 mph on my boat. Thanks again !

[@jbdtarheel]

Hey I have one just like this and I love it. The only issue is the tilt lock will not engage in reverse. Any idea what could be wrong?

[@THISOLDOUTBOARD1]

Hey. Check the spring and linkage, it may just be stuck and needs greased. Thanks for watching ! www.marineengine.com/parts/johnson-evinrude-parts.php?year=1971&hp=9.5&model=9R71R&manufacturer=Johnson&section=Stern+Bracket

[@thetruebrit85]

@@THISOLDOUTBOARD1 Excellent great to know.

[@Hawkman000]

Congrats on 90 subscribers your channel is growing!!!!

[@THISOLDOUTBOARD1]

tanks mon!

[@julianhernandez8837]

Hey I need the spark plugs!!! New to boating and dont know what are they

[@THISOLDOUTBOARD1]

Hey. Number 13 on the schematic. Champion J4J. gapped at .30 Thanks for watching and commenting. Stay tuned ! www.marineengine.com/parts/johnson-evinrude-parts.php?year=1971&hp=9.5&model=9R71R&manufacturer=Johnson&section=Cylinder+%26amp%3B+Crankcase

[@bahadirdogan6208]

I am getting 65 psi compression? What should I do?( same outboard)

[@THISOLDOUTBOARD1]

It may run ! There is a lot of info at leeroysramblings.com on theses motors, and I believe he said these motors will run as low as 60 psi. Everything you need to know is at leeroys. Check it out ! Thanks !

[@johnallex2344]

how fast did you get it

[@THISOLDOUTBOARD1]

Hey. Thanks for tuning in. Those 9.5's would run 17-18 mph on my 15' Duracraft jon boat. Thanks again & Stay tuned !

[@chuckcecconi4571]

I have a question, I recently pulled the lower unit on a 1972 Evinrude 9.5 hp sportwin.. my situation is, the oring on top of the drive shaft stayed in the powerhead ... How do I get it out of the powerhead?? HELP PLEASE.. love your videos brother

[@THISOLDOUTBOARD1]

Hey. Thanks. I Hate when that happens. Try a wire coat hanger, straighten it out and bend the tip to fit up in there, then put the other end in a drill and spin it. Then get a new o-ring ! Dont forget to grease it up when you put it back in. Thanks again. Stay tuned !

[@thetruebrit85]

@@THISOLDOUTBOARD1 You sir are a absolute legend. This information that you kindly share is indeed very much appreciated.

[@THISOLDOUTBOARD1]

@@thetruebrit85 Hey. Thanks for watching and commenting. really appreciate it! Stay tuned !

[@moos_578]

how much oil do you throw in the gasoline?

[@THISOLDOUTBOARD1]

Hey. 50:1, 2.56 ounce per gallon or gas. Thanks !

[@gsallen9588]

That your smoothie, maun! No prowblum! Do ya think that compression might step up a little after operation?

[@THISOLDOUTBOARD1]

ya mon, dat me smoothie mon. WHAT A MINUTE , I thought a smoothie was something for ironing clothes! anyway, i doubt the comp will com up but u never know, all the 9.5's i've had were right around 80psi. i hear they still run good at 60!

[@gsallen9588]

Wow. That's a singular tendency to know. I like that long-lived feature.

[@petermoyes8766]

i just bought a 1976 9.5 evinrude sports twin ...it isnt running been used maybe over 8 yrs ago ,sat in a cottage ,,i paid 180 bucks for it ,it looks all origional ,,everything is correct as i can see ,,,i am just gonna put new plugs and try to start it ,,its got a ton of compression ..and i want it for my 10 ft rib boat ,,can you tell me the socket size to remove the fly wheel ,,got no spark so coils and whatever else ,,,and new impellor ,,i will need your advice and knowledge as i work my way thru it ,,i am 70 and i like the weight of this motor ,,but honestly i have not got a clue what i am doing lol ...peace bro ,,love your vids ..my mechanic on a budget ,,thanks for your down to earth vids

[@THISOLDOUTBOARD1]

Hey Sounds Good ! check the model numbers for the year. Anyway way I can help Just ask. Great little motors and run forever. Here's Where I learned everything ! www.leeroysramblings.com/OMC_9.5.htm . Let me know how things are going . Thanks again. Stay tuned !

[@rustyedmoore]

I was worried the first time I watched the video, I didn't have any audio. Thought you may have had laryngitis! or maybe you were harking back to the silent film days! LOL Then I came back an some whacked out Jamaican was talking. A little too early for smoking the Guanga. I know is medicinal!!! Hope my Bigtwin/Lark hybrid runs like that. Later -Ed

[@THISOLDOUTBOARD1]

ya mon, ima shuu it will!

[@victorremick9721]

THE NEW 4 STROKES HAVE NOTHING ON THE OLD 2 STROKES. SMOKE A LITTLE BUT WHO CARES. THE SMELL OF A OUTBOARD IS A WELCOME ONE FOR SURE. COUS WHEN THERE ANT NO SMELL THERE ANT NO MOVEMENT.

[@THISOLDOUTBOARD1]

Hahaha 👌 thanks

[@igotmesothelioma]

By far my least favorite outboard to work on.

[@THISOLDOUTBOARD1]

yep! thanks !