It's amazing how projects sometimes put up a hard fight. The fight makes it all that much more satisfying when you win.
@blackmouthcur60972 жыл бұрын
Good job on this build. I appreciate your attention to detail, thanks for the step by step process you do.
@stevewilliamson8526 Жыл бұрын
Thanks for the video , just bought one without spark and always appreciate some insight before I tear something down. Nice work.
@6tringplayer483 Жыл бұрын
Great Job! Thanks, Just acquired a 1970 evinrude 9.5 .Plan to rework it. I believe it to have a broken motor mount. Your videos will help me in the restoration process.
@gregriley6492 жыл бұрын
Awesome job on the 9.5 👍 great video .keep them coming
@gerrydunne87682 жыл бұрын
Looks like it is running really good well done
@ronaldbrown57452 жыл бұрын
Good info on the challenging but good running 9.5!
@therosses52 жыл бұрын
Oh man, Brandon. I LOVE your channel and videos, but this is like watching a butt dial video. Gave me a bug chuckle...probably because this is also a day in my life!!
@bennyblanko32 жыл бұрын
Great job! You are awesome!
@mlbabineaux2 жыл бұрын
Me and my brothers had one of those in the 1970's and 80's. It was a real trooper !
@stevengraham1852 жыл бұрын
Beautiful Motor !!! I could feel the Power 😃
@tombell80992 жыл бұрын
Hey Brandon, your series on the Turtle motors is great and it helped me a lot. I picked up a '67 that hadn't run in more than ten years. It shifted, felt like it had good compression, had spark and the price was right. New water pump, thermostat lower unit seals, carb kit, fuel pump, ignition set and three days of struggling to unseat the drive shaft from the crank shaft (had to build a special tool to separate them). Finally, I am coming up on the moment of truth. I hope it purrs like yours. I have one last thing to do and that is to figure out where a small spring goes (OMC 0312164 - Spring). The parts blow up is not very helpful and the shop manual is silent on this.
@BrandonsGarage2 жыл бұрын
In this video - kzbin.info/www/bejne/gYOzqWSXl8l3d80 You can see it at 5:40, where there is a top view of the ignition system Half way down the idle adjust knob/spring/needle, and help keeps it in place. There are 2 holes in the lower cowl to clip it on. You can see it again at 6:34 You wont see me remove it, as once the needle is out, spring is loose and falls off. However, I install it at 45:11
@tombell80992 жыл бұрын
@@BrandonsGarage Thanks Brandon. That solves that problem. I noticed your comment about replacing the fuel line without taking apart the the arm. I can't quite make out what kind of fuel line you used to avoid that. I set my points with a feeler gage but started looking for a timing tool. By luck I found someone who used a 3D printer to make one. I should have a copy printed by tomorrow.
@DanPrescott2 жыл бұрын
I am currently working on rebuilding a Johnson 9.5, needless to the say the quote of "it was a challenge every step of the way" hits so close to home.
@DanPrescott2 жыл бұрын
Honestly I am stuck. I cannot figure out how to get the points plate to throttle linkage back together and no where can I find a picture of it.
@jimstaines80932 жыл бұрын
👍 nice Slip a lil piece of PVC pipe over that tiller
@joelbjorkstrand74392 жыл бұрын
Do you happen to know what dimension the flywheel nut is? Mine is stripped, and the motor is also missing the cover for the puller holes. Is the cover really necessary, or would you say it’s replaceable with a fitting washer? Thank you for your great videos!!
@tonycanning81793 ай бұрын
I got put weight in front mine too, boat is bouncy if more weight in back. Fast and cheap on gas.
@denttech84472 жыл бұрын
My grandpa had a 1969 Johnson 9.5 on a homemade wood jon boat . He told me fishing when I was a kid it would probably do about 10
@johnaitchie3803 Жыл бұрын
He's wrong lol I get 22mph out my 1967 johnson 9.5hp on a 230 sib
@davekimbler23082 жыл бұрын
On a few of my turtle tops they have plastic props ! Hit a rock with those and it’s toast ! Lol
@isaiahholland4440 Жыл бұрын
What pitch prop are you running currently with a 7 pitch my 72 9.5 only does 14mph on my gheenoe
@michaeldickinson32522 жыл бұрын
I have a 1965 9.5 and at wot it surges pretty bad. It seems intermittent though? Coils replaced a few years back. Fuel pump?
@WoodGuy2 жыл бұрын
That was a good rebuild, I didn't know exhaust fumes could get inside the engine cover. Does that only happen with this design or can it happen to all outboards?
@davekimbler23082 жыл бұрын
Some more then others , that’s why the gasket is on the leg !
@michaelnentwig84652 жыл бұрын
Wonder how fast it would go with the top off?
@FabioBrazilSP Жыл бұрын
Como fica a abertura da borboleta do carburador quando acelera totalmente ? Atinge a abertura total ou ainda sobra curso pra abrir mais ?
@evinrudej2 жыл бұрын
Which boat do you have ?
@harrycarlock8002 жыл бұрын
I have a 1973 9.5 that i have ordered points twice from marineengine and both times when i put them in they dont open up. i put the old ones in and it opens fine. what is the part # you use for your points so i can compare? mine is 172522 tuneup kit.
@blackmouthcur60972 жыл бұрын
He did a video about the parts. Check it out, he went through 3 different sets of points, the information you are looking for is there, you just NEED to LOOK for IT!
@SteveB-hy2ci4 ай бұрын
I got one now I want. To fix it up,didn't know it would be that fast for a 9.5😊
@BrandonsGarage4 ай бұрын
It's all in the prop, boat weight and distribution, and how well it's running.
@SteveB-hy2ci4 ай бұрын
@@BrandonsGarage yep, and adjusting the tilt of the motor just rite. Thanks, I'm putting together it and 14' 1967 alumacraft deep v.
@tonycanning81793 ай бұрын
Tilt is very important, I use The second last hole and put gas can and whatever else in front. Fun fast riding
@montanahelp21692 жыл бұрын
I have a chance to get one of these 9.5s. Is there much difference between the 9.5’s and the newer 9.9 2 strokes? Any noticeable difference in power?
@BrandonsGarage2 жыл бұрын
Power? Eh, I haven't used a 9.9 recently to compare the two. However a 9.9 is superior in every way. Buy the 9.9
@montanahelp21692 жыл бұрын
Thanks. I appreciate all of your video’s
@johnaitchie3803 Жыл бұрын
In what way I have a 9.5 and it has never let me down
@bebeslife4519 Жыл бұрын
@@johnaitchie38039.9’s we’re rated at the prop while the older motors like the 9.5 are rated at the powerhead. So the 9.9 would make a decent amount of more power
@NilsJakobson2 жыл бұрын
Could not understand what you were doing to make it go faster. Different props? Depth or angle how the engine is attached? Just got 69 Evinrude 9.5 in unknown condition for rebuild project.
@BrandonsGarage2 жыл бұрын
yes, adjusting the trim setting / rod
@ThePredsmaniac2 жыл бұрын
I just acquired one of these in decent shape.....can you confirm the oil mixture of 3 ounces of 2 stroke oil to one galleon of fuel? Thanks DS
@maxwilliams78342 жыл бұрын
I personally run 2.5 ounces of tcw-3 per gallon and mine is running great, the ratio is 50:1 if you’re curious
@ThePredsmaniac2 жыл бұрын
@@maxwilliams7834 Thanks for reaffirming that I troll allot and go 3 ounces to one Gal.... love this engine sounds like a P51 Mustang taxiing out on the runway tight lines
@mikeprehotsky7293 Жыл бұрын
Im thinking mine has an issue with the revs getting up there. Mine tops out at 7 mph with 2 people.
@750rocketman5 Жыл бұрын
Yeah you need a carb rebuild and a decarbon, my 6hp will do 12 with 2 people
@jojovideos95368 ай бұрын
is your boat a gamefisher , and what size boat?
@BrandonsGarage8 ай бұрын
That was a Lowe 12 or 14' I don't remember
@user-vt1io5tj5q Жыл бұрын
Can’t get my motor to tilt. Any suggestions?
@tonycanning81793 ай бұрын
Greased? Could be stuck from not greasing
@jaxonsadventuresandgaming43144 ай бұрын
Can you tell me how you control the pitch of your motor?
@tonycanning81793 ай бұрын
A bar slides through holes stopping the motor from going straight down
@jaxonsadventuresandgaming43143 ай бұрын
@@tonycanning8179 Thank you.
@JamesSmith-jr2rc2 жыл бұрын
What body of water are you in?
@BrandonsGarage2 жыл бұрын
colorado river
@JamesSmith-jr2rc2 жыл бұрын
@@BrandonsGarage the water sure is clear.
@anthonyadams6936 ай бұрын
What length is the boat?
@tonycanning81793 ай бұрын
12-14 ft.
@dennisfalan16232 жыл бұрын
How big is that boat?
@tonycanning81793 ай бұрын
12-14 ft looks like. Got a 9.5 on my fiberglass 12 ft.
@TheSFCjaymo Жыл бұрын
I can’t figure out why my 9.5 Johnson only goes 5 mph!!!
@BrandonsGarage Жыл бұрын
Probably running on one cylinder. ..or very bad weight distribution on the boat.
@TheSFCjaymo Жыл бұрын
@@BrandonsGarage thank You 🙏 so much for replying!!!
@123pwop2 жыл бұрын
Don`t want to be on that fast moving water with an "IFFY" motor !! Just saying.
@65yelrah2 жыл бұрын
Wow urs is fast. I cant get my more than 7.2mph.
@BrandonsGarage2 жыл бұрын
running on one cylinder?
@65yelrah2 жыл бұрын
@@BrandonsGarage nope runs on both. New coils and carb done. Starts and runs great. Takes off like crazy and pulls until 7mph.
@evinrudej2 жыл бұрын
@@65yelrah is the boat getting on plane ?
@65yelrah2 жыл бұрын
@@evinrudej not sure, seems like it does
@evinrudej2 жыл бұрын
@@65yelrah what size boat? I was having the same problem until I re trimmed and put a new prop on then it went from 8mph to around 15 mph