1976 Evinrude 15hp outboard motor

Рет қаралды 1,942

chrysleroutboarddude

Күн бұрын

Пікірлер: 32

@donk499 7 ай бұрын

Boy o boy, I'm surprised all the snow and ice is gone! Saving that old low tension motor shows true dedication Ben!

@fleetwin1 7 ай бұрын

Wonder what happened internally... Took a swim? Water in the gas? Bad lower seal?

@chrysleroutboarddude 7 ай бұрын

@@fleetwin1 Again I have no idea! The motor was missing the flywheel when I bought it though.

@Mitch-m7z 6 ай бұрын

I remember watching you back when i was like 13-14 in 2011-12ish after my dad got a 80s evinrude 9.9 and i was so interested in it! Cant believe i found the channel and you still upload! I remember not understanding how you said your name and still don't lol!

@tommyandersen3657 7 ай бұрын

Those old little guys. Nothing better than those.

@Kelemen1 7 ай бұрын

Sounds very very healthy

@unbeatable815 7 ай бұрын

Really worked your magic on this - super impressed

@labradorguy5311 7 ай бұрын

Great to hear from you again! You saved another one! It does sound and runs nice.

@jcamp348 7 ай бұрын

Wow, that's a lot of work! Never disappoints. Great job. Really tops out nice and idles down great. I really enjoy these videos. Thank you.

@clayrundquist5098 6 ай бұрын

Nothing compares to sound of the 15 hp Johnson/Evinrude at full throttle.

@oldjohnnyrude8404 7 ай бұрын

Lot of work done to that one. I have an '81 9.9 that I need to split the case on and replace the bearings in. It will be a nice motor when i get it done. This one sounds great now. Nice work!

@chrysleroutboarddude 7 ай бұрын

It’s not bad to replace the crank bearings takes about two hours

@oldjohnnyrude8404 7 ай бұрын

@@chrysleroutboarddude I'll have to try to get to it this year.

@michael0567 6 ай бұрын

Hello, I have a 1970’s Chrysler 15 hp outboard, I think it’s a 75 but I’m not sure, I had it running but when I go to give it gas it almost “slips” in drive. It will only rev half way before “slipping” and bogging back down. I saw your name and thought you might know something about Chrysler motors, just wondering what I can check out to try to fix it. Thanks!

@Riverbottombrewer 6 ай бұрын

I have a 9.9 Chrysler and cant find much information. The starting system is a rotor and stator system, not a side mounted gear drive starter. Tryn to chase wiring because it will run if you keep power by holding key over on start....

@mark_osborne 7 ай бұрын

Nice job- she runs great !

@HandelTelford 5 ай бұрын

Hey buddy, i really appreciate what you do. I got a 1969 9.9 that i cant figure out why im not getting spark. I was only getting spark on the lower cylinder coil. Changed the top coil and now im not getting any spark on either lines. your thoughts in general? by the way i cleaned the points and changed the condensors. both coils are good, what else could kill the spark ? have you run into a problem like this with the chryslers?

@anitagils 6 ай бұрын

hello i am looking for help with my 1988 force 9.9hp. the head will sizzles water when splashed at idling after 1min . water pump has good pressure, power head base gasket has been replaced head gasket has been replaced, exhaust gasket replaced ,carb has been cleaned many times but still runs hot, but it has never seized even at full speed. any help would be much appreciated thank you

@omcdude64 7 ай бұрын

Nice

@johnnymissfire8464 7 ай бұрын

She's a little ripper!

@douglaskaye1395 7 ай бұрын

Good job!

@marksmith4582 7 ай бұрын

Nice rebuild of a barn find Ben! A really decent runner! How are you, Mary, and your little one doing? It’s been a while! Nice to see you posting again! Your neighbor Mark in Iowa.

@chrysleroutboarddude 7 ай бұрын

Everyone is doing well! Thanks for asking