Working on cars is always a journey. Patience always helps.
@WoodsTreeFarm4 жыл бұрын
Very true! Ran the car almost 100 miles today with numerous stops. Never encountered the rough idle thing again. But it was warm again today. We'll see how it does when cooler weather returns next week.
@TheSkubna3 жыл бұрын
I take my PCV valve and drop it in a container of gasoline, injector, carb cleaner, etc, and let it soak a few hours, seal and shake the container real good. Hit it with a brass wire brush and you can put it back in once its dry. I've never seen a subaru pcv break, just get clogged. (Although with a new one on many subaru engines it can take 2 minutes to replace). If the idle is still an issue, clean the idle air control valve and EGR. Next try to remove the upstream oxygen sensor(s) from the exhaust. Take them in a dark area and hit the end of it with a propane torch until it just starts to glow. Let it sit a minute and hit it with a brass wire brush inside the little vent holes.
@WoodsTreeFarm3 жыл бұрын
Good info. Thanks
@Enonymouse_ Жыл бұрын
PCV's are about 17 bucks, unless your in a dire situation, it's better to replace it. The dealer recommended using liquid thread sealant on the pcv to prevent leaks.
@joefi883 жыл бұрын
Had the same crunchy plastic sound and got scared but it’s all good. Thx.
@Enonymouse_ Жыл бұрын
Technet offers some low cost options for shade tree mechanics. If your not familiar, its the technical info for mechanical information or diagnostics.
@cruzafix13 Жыл бұрын
Just bought a 2010 Forester has anyone noticed any jumping in the transmission like it wants to go fast but it cant
@jamezbond783 жыл бұрын
Thanks for the video! My 2010 Subaru Forester is experiencing a similar issue. It seems to idle alright but if I go forward or in reverse and brake, the RPM drops and the car stutters or stalls. Is this what you were experiencing? I was getting a P0420 code for catalytic system. I've replaced the catalytic converter, oxygen sensors and almost every sensor I can think of and the problem still exists. This week going to replace the purge valve. If that doesn't work I might have to replace PCV valve.
@WoodsTreeFarm3 жыл бұрын
Yeah that sounds similar but it was really intermittent for us. But the studdering and stalling hasn't returned since I replaced the pcv. Good luck!
@charlesalbrecht62013 жыл бұрын
Currently dealing with the same on a ‘10 Fozzie Xt 2.0 keep coming up with research pointing to torque converter or valve gasket failure
@Eazy9272 жыл бұрын
Kinda late but did you try to reset the idle?
@snoorani1 Жыл бұрын
I had same issue. I have by now changed all Plugs, cleaned every sensor I could access, tried resetting the idle. Nothing has worked so far. I have a feeling PC. valve may well be the issue
@jamezbond78 Жыл бұрын
@@snoorani1 are you getting any error codes? Did you try doing the idle relearn procedure?
@DanielAtkinsFirewood4 жыл бұрын
I make parts for the Mazda rotary cars. I can also help diagnose issues over the phone or email. So working on cars can be fun and a headache. Hopefully this fixed your issue..
@WoodsTreeFarm3 жыл бұрын
So far, so good. Thanks Daniel!
@patriot34318 ай бұрын
I had to use long needle nose pliers to get it started and cussed a blue streak getting the new hose on the valve.
@kevinnorwood73552 жыл бұрын
My car stalls and has no power and won't go over 50 MPH. I've cleaned out the MAP sensor and changed the oil. It has a new battery and I swapped out the one ignition coil causing the engine light to come on. Replaced all the plugs too. So I hope this works with no check engine light I'm at a lose.
@WoodsTreeFarm2 жыл бұрын
Wow. Best of luck. Another thing to check might be fuel filter.
@kevinnorwood73552 жыл бұрын
@@WoodsTreeFarm so the PVC did need replaced bit still no go. I'm guessing that it's under the rear seat on the passenger side?
@cjoakman7715Ай бұрын
Soooo........did it fix the rough idle and nearly stalling issue?
@WoodsTreeFarmАй бұрын
@@cjoakman7715 yes
@jimmyw85933 жыл бұрын
8:28 the whole part rotated when you turned the ratchet. Does that matter?
@WoodsTreeFarm3 жыл бұрын
yeah, seems to be fine. I tried to put a wrench on it to keep it from moving, but didn't have room. at 9:41 I put it back where it was when I tightened everything up.
@gavinjohnston79083 жыл бұрын
@@WoodsTreeFarm lucky it didnt snap off ....did it fix the problem?? no test result
@bradsouthers74763 жыл бұрын
@@WoodsTreeFarm I have the same problem where the bottom part turns. I've not been able to identify the part so I don't think it's replaceable if I break it. When you turned it, did it stop on its own or did the side pipe butt up against something that stopped it? I'd be worried about breaking the pipe off if that's what stopped it.
@bradsouthers74763 жыл бұрын
I did find a solution for this. You can use a 1/4" bolt or similar object to wedge between the lower part and the engine block. This stops that part from turning while you break the PCV valve free.
@dmalloy964 жыл бұрын
Great video did that end up fixing it hope so
@WoodsTreeFarm4 жыл бұрын
Don't know for sure, but we haven't had the rough idle issue return yet.
@cyberedwing3 жыл бұрын
today s 10/1/21 did the rough idle return?
@WoodsTreeFarm3 жыл бұрын
No, it never returned. This definitely seemed to be the fix
@cyberedwing3 жыл бұрын
@@WoodsTreeFarmthanks Ill try it myself
@MikeSorrell-lp7zf4 ай бұрын
keep doing that with the blue light on.......see how long a unwarmed up transmission holds up.
@WoodsTreeFarm4 ай бұрын
ok
@PeterHernandez-lg2eh6 ай бұрын
Did you get a cel code like po302
@WoodsTreeFarm6 ай бұрын
No codes
@PeterHernandez-lg2eh6 ай бұрын
Not so easy on a Subaru sti
@ekim955yt11 ай бұрын
Buy me a coffee for wasting my time. Was this a video about how to use wrench or how fix an idle problem?
@wesleyyazzie9001 Жыл бұрын
Dude your messing it up
@WoodsTreeFarm Жыл бұрын
haha. doubt it. We ran this car another 2+ years after this video before trading it in. No issues.