1990-1997 Accord Brake Job (Captive Rotor Replacement) Hub Over Rotor Part 2

  Рет қаралды 46,136

Bushougoma

Bushougoma

Күн бұрын

Пікірлер
@Q50WO
@Q50WO 11 ай бұрын
Hands down the best tutorial video I've seen. Clear views and aspects, helpful tips and thorough instructions. I appreciate you very much bro. Literally about to do this on my 94 Accord EX Wagon. Thank you.
@jimbarron8688
@jimbarron8688 3 жыл бұрын
Perfection. Watching this video was like reliving my worst nightmare... sure wish I knew this detailed explanation was available when I suffered this backwards design .
@ocalastingfan
@ocalastingfan 6 жыл бұрын
This video was by far the best on the inter web. Great job on showing the whole process especially the removal of the rotor. Before watching this video I was getting worried we would never be able to get the rotor assembly off but with your suggestion of using the 4 bolts and air hammer it cam right off. Brilliant instruction and excellent video. All in all your video saved me a lot of money and aggravation. Thanks so much.
@wilfredosantiago-tufino3678
@wilfredosantiago-tufino3678 4 жыл бұрын
Excellent tutorial!!!! Had my 1991 Honda Accord rotors serviced. You didn't miss a beat. Knowledgeable of job. No problem. I admire your patience. Your the best...!!! Keep up the excellent job .Proud of doing it myself because of you...
@robertweir9034
@robertweir9034 5 жыл бұрын
Again, part two covered everything and with all the proper procedures. The only, and I mean only, error I saw was to reposition the piston boots after collapsing the piston so they would not be pinched by the inner pad. Also, the problem with using antiseize grease is that it is petroleum based and this can do harm to rubber. Always use silicon paste anywhere on a brake system. Still, the best video on this subject on the web. SMA would be proud.
@SDsailor7
@SDsailor7 5 жыл бұрын
This is the best tutorial i have seen here on YT bar none!Very clear with plenty of tips to make the job a little bit easier. What a nightmare of a job just to replace a rotor!!
@quintencolovich9504
@quintencolovich9504 4 жыл бұрын
I watched this for my 97 coupe to change my prepressed bearings, really helped, thanks man
@jacobfield4420
@jacobfield4420 8 жыл бұрын
Hey man. I've watched a few of your videos as I have a 97 Accord. Thanks so much for your help. Your videos are thorough and easy to understand. You have saved me a lot of time and money! Thanks again!
@stillrumone
@stillrumone 10 жыл бұрын
THANKS FOR SHARING YOUR KNOWLEDGE... IT IS EXTREMELY HELPFUL, AND APPRECIATED...
@ZPDSurvival
@ZPDSurvival 7 жыл бұрын
181 ft. lbs. Cool. I have owned seven 1989 Honda accords since 1994. Bought a 97 last year and here we are. Great instructional video for this rather long surgery. Thanks.
@tylerhamby7771
@tylerhamby7771 7 жыл бұрын
Can you please do rear brake drum and shoes replacement(1996 Honda Accord)? You're the best honda guy on youtube!
@TheVanillaChapstick
@TheVanillaChapstick 7 жыл бұрын
I second this
@michaellamasjr6201
@michaellamasjr6201 4 жыл бұрын
Best video I’ve seen on KZbin amazing job
@henrylahud5156
@henrylahud5156 4 жыл бұрын
Thank you so much for making this video! It really helped :)
@giegiofoncho
@giegiofoncho 6 жыл бұрын
Thank you for taking the time todo this great video good job
@jimmyhudzgarage
@jimmyhudzgarage 10 жыл бұрын
Thank you for making such a detailed video. I need to replace the rotors and pads on my mom's 1997 Accord and wasn't sure how to do it correctly. I took notes while you worked. Very well done, thanks again.
@tonyisme4934
@tonyisme4934 Жыл бұрын
Your videos great and detailed. What is the torque setting for the 36 mm axle nut I noticed my nut was loose, wasnt staked down to the axle gap
@robertburns4752
@robertburns4752 Жыл бұрын
Very good video ❤
@pauljohnson-yk5dq
@pauljohnson-yk5dq 9 жыл бұрын
Great video and good lighting. Thanks for posting.
@theavenged7297
@theavenged7297 8 жыл бұрын
Getting the lower control stud into the lower control arm (6:20), if the stud doesn't reach the control arm hole does that mean the axel isn't flush with the rotor?
@lilyo6205
@lilyo6205 9 жыл бұрын
Excellent, very detailed. Thanks for sharing
@istmanblade5382
@istmanblade5382 5 жыл бұрын
I was wondering if it is possible to rotate the disc rotor in case of pedal pulsating due to DTV, on car if you unscrew the 4 rotor bolts and rotate?
@spelunkerd
@spelunkerd 10 жыл бұрын
Nice job.
@squirrelmaster760710
@squirrelmaster760710 3 ай бұрын
What would happen if you place the slide pin bolts in the wrong place, (g in the l, and l in the g)
@garoldjang9929
@garoldjang9929 7 жыл бұрын
will the outside hub come off by removing the 4 bolts. I need to replace the studs.
@vanquishstorm3806
@vanquishstorm3806 5 жыл бұрын
Thanks for the vid. it was very informative. I will be using this as a reference on my 97' Accord. When you lift up and swing out the knuckle assembly from the ball joint, did you also detach the joint from the tie-rod? Thanks again.
@Bushougoma
@Bushougoma 5 жыл бұрын
No you can leave the tie rod attached.
@vanquishstorm3806
@vanquishstorm3806 5 жыл бұрын
@@Bushougoma Ok great. Thank you
@tubejim101
@tubejim101 9 жыл бұрын
Great video!
@sleepyallycat7264
@sleepyallycat7264 9 жыл бұрын
Thanks to this video this process will be $300 max instead of $500+ and a need for an auto brake leith. Also, where can one find the Anti-Rattle clips for this model, all I can find are ones that look similar for 2000s and up models. TIA
@Bushougoma
@Bushougoma 9 жыл бұрын
+Demon Child Just ask for a brake hardware kit for the front all of the clips come with it. Numerous aftermarket manufacturers make them.
@napol5849
@napol5849 6 жыл бұрын
Thanks for the upload stay bless
@mmashmash
@mmashmash 2 жыл бұрын
Why do you mess with the bleeders, rather than just opening up the main resivoir?
@joeynicolas4118
@joeynicolas4118 8 жыл бұрын
great job, thanks for your help
@Vfh........y
@Vfh........y 8 жыл бұрын
great vid.........well done.
@Langelierdesigns
@Langelierdesigns 9 жыл бұрын
Good stuff! I feel your pain! This is not a fun thing to do.
@russellatwell2000
@russellatwell2000 7 жыл бұрын
very informative thank you
@claudiobasquete
@claudiobasquete 10 жыл бұрын
Ótimo trabalho parabéns!
@carlitosdelcid
@carlitosdelcid 8 жыл бұрын
exelent video thanks!!
@petu80
@petu80 9 жыл бұрын
good video
@jorgemcaldas
@jorgemcaldas 8 жыл бұрын
Hi, my question today is, when do I know that I need to replacement the captive rotor? Thanks.
@Bushougoma
@Bushougoma 8 жыл бұрын
Ideally they should always be machined (or replaced) to restore a flat surface for the new pads to break onto. Rotors are so cheap nowadays it doesn't pay to remove them, machine them, and reinstall them unless you have an on vehicle brake lathe.
@jorgemcaldas
@jorgemcaldas 8 жыл бұрын
Good, do you know why, when I press the break pedal, after I start engine, the ABS light goes on and doesn't turn off only after I turn off engine???? I like so much watch your videos because you care about everything you do... I am not mecanic but I want learn how fix my accord 95 because I like care about it. Thank you.
@ZillaYT
@ZillaYT 8 жыл бұрын
Great videos, both part 1 and part 2. One suggestion, use the "speed up" video editing tool more often - you did in some parts but could've used it a lot more.
@zmelli
@zmelli 5 жыл бұрын
I thought 180 ft/lbs was for the Wagon?
@ZacVaper
@ZacVaper 11 ай бұрын
***** Stop wasting your brake cleaner...just clean once, after everything is assembled. ***** Throw out these hubs and get yourself the 98-99 Acura CL 4cyl hub ($150) and rotor set, bolts right on and uses same calipers.
@cheeseball247
@cheeseball247 10 жыл бұрын
I hate Honda for this design. Ugh!
How to Replace Front Brakes 1994-1997 Honda Accord
26:13
Mom Hack for Cooking Solo with a Little One! 🍳👶
00:15
5-Minute Crafts HOUSE
Рет қаралды 22 МЛН
人是不能做到吗?#火影忍者 #家人  #佐助
00:20
火影忍者一家
Рет қаралды 20 МЛН
Мясо вегана? 🧐 @Whatthefshow
01:01
История одного вокалиста
Рет қаралды 7 МЛН
So Cute 🥰 who is better?
00:15
dednahype
Рет қаралды 19 МЛН
25 Wildest Old Cars of All Time You Forgot About!
26:22
Retro Rides Garage
Рет қаралды 5
Most Common Brake Installation Mistakes!
13:29
1A Auto: Repair Tips & Secrets Only Mechanics Know
Рет қаралды 4,7 МЛН
Honda Accord Captive Rotors/Wheel Bearing Hub Assembly - Removal and Installation
36:27
How To Perform a Professional Brake Job (Pads & Rotors)
38:48
Royalty Auto Service
Рет қаралды 971 М.
1994-1997 Accord ABS Modulator Replacement
27:13
Bushougoma
Рет қаралды 47 М.
Honda Accord Captive Rotor Delete
28:12
Stay Tuned Garage
Рет қаралды 20 М.
We try Tik-Tok brake disc resurfacing method
14:33
Garage 54
Рет қаралды 475 М.
Reemplazar Disco de Freno (replace captive rotor) Honda Accord 1990-1997
3:31
The Little Lion y Su Proyecto
Рет қаралды 4,6 М.
New Tires With Wheel Alignment Scam - Avoid Rip Offs
20:30
Pete's Garage
Рет қаралды 3 МЛН
Mom Hack for Cooking Solo with a Little One! 🍳👶
00:15
5-Minute Crafts HOUSE
Рет қаралды 22 МЛН