Thankyou! I am changing my lower shift cable on the 2011 Silverado. The E clip was giving me trouble and thanks to your video it helped! I am going to give it a try, i am almost done with the job!
@danieljensen24272 жыл бұрын
I bought both of these separately GM cables different dealers, spring clip may not be included,
@mrebpropertiessobota33263 жыл бұрын
@ 8:30 you show that the cable is properly adjusted. After doing the entire cable's replacement, the shifter moves through the full range from "R" to "1". However, coming back up to Park the shifter does not return to "P". The cable is loose, any suggestions? Your video shows no remedy for the problem.
@RenaissanceThinking2 жыл бұрын
I'm having that very problem today. Did you figure out a solution?
@nopenottanoway Жыл бұрын
Mine is the opposite, I can get to all the gear positions except for the low gear. I tried every position on the adjuster and can't find the correct position.
@ken1180 Жыл бұрын
If it won't go to Park, shorten the cable housing. If it won't go into 1st, lengthen the housing.
@thanosetsitty18964 жыл бұрын
I totally agree with what you said at the end of the video. That is why I try to work on my own vehicles as much as possible.
@elgarfio4186 Жыл бұрын
Thanks so much for taking the time to share this information! God bless!
@drakewilson59535 жыл бұрын
What did you call that funky looking clip inbetween the 2 cables
@danieljensen24272 жыл бұрын
Spring clip,new GM cable doesn't come with one
@johnknecht69584 жыл бұрын
My 98 2500 W/T won't go into 3 2 or 1 and now is starting to get stupid about shifting into drive. I'm going to take a look at the Shifting cables. Thanks for the great video
@benkanobe75004 жыл бұрын
What was the reason for the cable replacement??
@micheal_-hn9ye2 жыл бұрын
ok i got a question to ask u i have a new shift cable and the clip snapped in half on me and i got new ones and it still doesn't not want to clip to together doesn.t it matter which way u put that clip in and doesn't it go inside or outside because i'm starting to go crazy on this truck it's a 2000 chevy silverado 1500 with 3.5 v8 4x4
@96z28camaro15 күн бұрын
I've done 5 of them this way and now I'm having issues putting it back in.
@CertMonkeyTrainer5 жыл бұрын
Thanks! This video is just what I needed.
@brianfelt91384 жыл бұрын
I put a new cable set in my truck and can't figure out how to adjust it to hit all shift points? ( won't drop into 1 ) and the shifting is now sloppy? Anything will help at this point.
@Ducatislave4 жыл бұрын
I would not be inclined to say that the cable is causing sloppy shifting. If your cable is misadjusted you will simply not be able to shift to a particular gear or you will be in a different position from what is indicated. If you are experiencing "sloppy", delayed or harsh shifting then in my experience you have larger problems with your transmission. Possibly a solenoid is failing/leaking by. Hope this helps.
@brianfelt91384 жыл бұрын
@@Ducatislave I don't think anything is going on with the trans. I put a new cable on because it was getting very stiff to shift from park to drive. After I pulled the old cable down and inspected it I found that where the 2 connected was rusted. So somehow I have to get it adjusted so I can utilize all shift points, and tighten up between the shifter and the trans. Thanks
@nopenottanoway Жыл бұрын
@@brianfelt9138 did you figure out how to fix it? I'm having that exact same issue with not finding gear 1 even after trying to adjust it.
@johnbautiste Жыл бұрын
I cannot get that connector at 7 minutes in with the clip to re attach.
@sheaadams864 жыл бұрын
My clip just falls back off, wont stay in place
@Toofargone6665 жыл бұрын
For some reason my new lower cable didn’t want to snap on the the little nipple thing where the cable connects to tranny. Was I not pushing it in hard enough or?
@amanhistoolsautorepair14875 жыл бұрын
No, it should click in fairly easy, unless you had a lot of gunk on there which may have gotten in the female/upper cable end. Your spring clip may not be in correctly.
@heathermackenzie2715 жыл бұрын
A Man & His Tools Auto Repair - Is there a secret to getting the copper clip back in? I’m struggling with that part.
@tamikajohnson-pitchford72352 жыл бұрын
Where do I put the clip, there is nowhere to put clip to bring clamo both pieces together
@jcjolly67632 жыл бұрын
od buttom not working ?
@fareedhussein92864 жыл бұрын
You do very very good job
@westthomas9338 Жыл бұрын
I can't get the cable to separate
@MannyRodriguez-p9e7 ай бұрын
Muy Bien explicado grasias por tu ayuda
@marioalavez.76473 жыл бұрын
Thanks es good video.
@JameAndy-iu4bs5 ай бұрын
Good information thank u
@imrmoto4 жыл бұрын
how do you adjust the cable if it stick e-mail the amswer thank you
@Fldavestone7 ай бұрын
Just did mine. Do not buy a cheap one,they are not the right length. My truck left me in the middle of nowhere,freezing and rainy. Got it home fixed it and sold it.
@drakewilson59535 жыл бұрын
Mine broke and i need another one
@gayleober71195 жыл бұрын
thank you for the info but hold the camera still
@Ducatislave5 жыл бұрын
My apologies for not having a tripod or assistant to hold the camera.
@heathermackenzie2715 жыл бұрын
S. Buffum - Replaced my lower cable today on a 2012 Tahoe. It worked fine for a couple shifts from P, R and D. When I got home and put it back into park and I tried to put it in reverse it got sloppy again. And now is acting like it was before. However, the bushing side is still in place. Do I need to just adjust the tension again? When we joined the cables we had it in Manual, then joined the cables then put it in park to finish the connection. Do I need to redo that step with what you showed in the last video? Release the bushing end and adjust the spring side until the cable lines up itself? Hope this makes sense to you! Love the videos, they are very helpful!!