√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*
@oharac41783 жыл бұрын
First thank you for the video. i must correct 1 thing. Once you get the exaust brackets off and u have just insulation left instead of ripping it out. Just take dust shield dow and tug gently on insulation at the same time and it will comeout in one piece.
@1AAuto3 жыл бұрын
+oharac4178 Thanks for the feedback!
@quintaylor4330 Жыл бұрын
you guys literally make the best "how to" car videos on KZbin. this would've been a shaky, 2 hour, unedited video off some dudes phone.
@berrywin Жыл бұрын
Best video so far concerning removing and mounting the oil pan on a 5SFE engine! Clear and thorough instructions!
@rickamador7197 жыл бұрын
took me forever to find a video with someone who actually knows what they are talking about great job dude
@jeeyuantan77113 жыл бұрын
these guys are legends for doing this
@brandonowens88072 жыл бұрын
Seriously. I have the 98 Celica, and NO ONE has a video on any maintenance. Thankfully these cars share the same engine.
@thegee-tahguy48772 жыл бұрын
I can't stress enough how having a lift makes this whole job HUGELY easier and MUCH faster. Working on your back in your driveway makes everything you have to reach up into a total pain for those old enough to drive one of these die-hards, especially if you're on gravel or in a tight garage. A lift affects what tools you use from extensions to lighting. It's fine if you do have a real lift, but with jack stands it's almost unfair to make people think it's nearly as easy as this video shows. I honestly do appreciate this video showing the steps, really, but I think it needs to be said you will be under your Camry all day , if not into the wee hours if you think this job can be done by most DIYers in an hour or 3, not to mention when/if the head pipe studs break, like 2 of mine did. How's about talking about contingencies when bolts starts snappin' off or one is stripped on your 207 year old Toyodal Clamry 2.2l?
@EricVonHunter2 жыл бұрын
Truth! I'm doing this right now on ramps.
@GF-mf7ml Жыл бұрын
I just diy a old 80s Mitsubishi, it's very hard.
@dbfcrell83002 жыл бұрын
There is a gasket for the 97-01 Camry 2.2l. I'm in the process of fixing a RTV gasket leak someone did b/c they didn't use the gasket or leave the sealer in a bead, so you may want to consider either buying a good gasket instead of making one out of sealer or leaving the sealer in a bead. Felpro makes a decent rubberized gasket that doesn't require sealer and is made for imperfect mating surfaces. This is still a great video that shows the whole job head to tail, so I thank you for posting it.
@phantomgaming81372 жыл бұрын
I'm in the process of doing this as well, I have the gasket but I'm debating just using rtv after watching the video and reading in forums about just using rtv. Except instead of spreading it I'm going to leave it in a bead
@davenstewart3239 Жыл бұрын
@Phantom Gaming Did you end up using it in a bead form? I thought about getting the gasket, but I have black RTV lying around. How did this turn out for you?
@peterwallis460210 ай бұрын
Top video. Many thanks. Kind regards from Western Austalia.
@Anthony_in_Bloomington_Indiana4 жыл бұрын
You have to drop the exhaust pipe just to reach a few bolts on the oil pan! That is an insane design! . I have a 2004 Toyota Corolla, and I'm learning how to change my oil pan gasket, before I do it for real. I am suddenly relieved that I have a Corolla and not a Camry. . And my Corolla oil pan has an actual gasket, which is much easier than dealing with gasket sealer. I bought one for cheap on Ebay Motors.
@pablogon982 жыл бұрын
Same here! Seems like a hassle having to remove so many parts of the exhaust only to replace the oil pan. And the gasket part too!, remember to line it up properly and torque the bolts in a criss cross pattern ;)
@glenglene84732 жыл бұрын
To change the oi pan gasket in the E90 BMW 335i would cost you $2,000. You have to drop the subframe and everything else to get to it.
@phantomgaming81372 жыл бұрын
The camrys have a cork gasket, so far its better just to do a rtv
@MrSparkymike14 жыл бұрын
Denatured Alcohol works great at removing silicone gasket material from metal surfaces. Use it along with a copper dish scrubber, wear gloves or the alcohol will remove all the moisture from your hands and your fingernails will split at the cuticles.
@zacinnc78 Жыл бұрын
man u have the best camry guides out there bar none !thx to u im keeping my gfs old camry going ! Also that AT had alot of oil on it too u reckon u had a leaking valve cover gasket?(especially on the backside which is hard to see)
@TheMrBennitoАй бұрын
Jeeze, i didnt expect this. Thats a lot of work, with the stupid exhaust in the way :((( not taking anything away from the instructive level of this vid, superb 👍
@pkemoh425 күн бұрын
I have a 1998 Toyota Camry and I just changed the oil pan. My guy didnt removed the pipe to get to the pan. This is new for me cuz I saw my guy doing it. Great video though
@dansap1004 жыл бұрын
I was getting different input after search, but I'm glad I found your video. It's very detailed and very clear. Thank you very much.
@chrisr.986 Жыл бұрын
Did you change the gasket if so any pointers. The gasket is in my to do list. I'm worried the bolts might break.
@hipolitoramirez4243 жыл бұрын
very helpful good video also i bought some new suspension assembly also got the gasket set for the toyota camry and damn the 1995 is running like champ thanks to the videos.
@1AAuto3 жыл бұрын
+Hipolito ramirez Thank you for your order! We'd love to hear about your experience. Here's a link to leave us a review on Google: goo.gl/i5JFNY
@Superhyperaktive3 ай бұрын
Great video, just one question; the block foam between the oil pan and transmission ripped apart when I tried to remove it. Im having trouble finding a replacement for it. Maybe i could just stick another piece of foam in there to replace it.
@cincomorales7 жыл бұрын
Love the video also you are a great teacher! You did an amazing job cheers ! God bless your heart
@1AAuto7 жыл бұрын
+jessie morales Thanks for watching. If any of our viewers needs to make this repair, we carry the auto repair part shown in this video on our website. Here is a link to them www.1aauto.com/toyota-camry-solara-engine-oil-pan/i/1aeop00057?KZbin&CTA+Comment&VIqEagP9h1w
@elgatogordo95232 жыл бұрын
Interesting that it does not need an oil pan gasket, just silicone and that's it!!! My 97 Camry has an oil pan gasket installed and started leaking recently. I'll follow your instructions and use premium silicone on the oil pan flange. Thanks for the informative video 👍
@1AAuto2 жыл бұрын
+El Gato Gordo Thanks for checking us out. Shop for high quality auto parts on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c
@simonsw94105 ай бұрын
I just tried to tighten those bolts, as many as i can reach. It worked, no more leak. 2001 Camry se
@Rekuzan8 ай бұрын
Question: Why would you use RTV as opposed to a preformed cork gasket? What are the advantages/disadvantages of using RTV?
@anonymike82802 жыл бұрын
I have a question here. You might know the answer. Is it possible to remove the oil pump housing without removing the oil pan? I think it might be possible to move it enough to get at the bolts holding the oil pickup to the housing. But maybe not. By the way, there is an aftermarket oil pan gasket available. That is what I would use, rather than silcone. Silicone requires the same skills as a cake decorator.
@bobbymoncada6861 Жыл бұрын
Thank you, sr. That was an amazing job.
@carlosgarcia-po1zr3 жыл бұрын
I am grateful for all the information you are sharing!!!thanks 👍👍👍👍👍👍
@blessedbean86843 жыл бұрын
Hello! Thanks for this. All your videos are very clear and easy to understand. I wonder if you could tell me what SIZE & SPEC are the OIL PAN BOLTS. I know they are 10mm head but I mean THREAD SIZE and LENGTH. THANK YOU in advance!
@stacksjohnson58962 жыл бұрын
Is the V6 similar or harder? the local oil change place cross threaded my oil pan drain....bummed out.
@darronlofton49983 жыл бұрын
thank you so much you guys are a life saver
@carlotv12122 ай бұрын
Great video nonetheless I was just wondering from the list why I needed the mallet
@itsmerch56154 ай бұрын
So instead of an oil pan gasket it’s just a sealant?
@soyeldiego48786 жыл бұрын
Great video! Be doing this job this weekend. Hope it’s easy as it looks...
@1AAuto6 жыл бұрын
+Soy Eldiego Thank you for the great reply. We love to empower our customers by showing you how-to perform your own auto repairs while installing our high quality auto parts. Have a great day! 1aauto.com
@joet48066 жыл бұрын
Great video! V Good Teaching skills, clear and concise. Exh. Flex joint ready to let go.
@1AAuto6 жыл бұрын
+Joe T Thanks for watching. Have a great day! 1aauto.com
@marks10345 жыл бұрын
Surprised sealer was spread and not left in a bead.
@jessiejohnston9056 жыл бұрын
Great video. Awesome. No complaints. Is it really better to use liquid gasket? I have the cork style.
@genericusername13655 жыл бұрын
The car was designed to use the FIPG sealant, not a traditional gasket. The torque settings were specified for the FIPG sealant and are thrown off if you use a cork gasket.
@rickamador7197 жыл бұрын
do you guys have a video on replacing timing chain gasket, I just replaced my oil pan and gasket on my 97 toyota camry le 2.2l thanks to you guys , come to find out that wasn't the issue if you guys can help it will be very appreciated
@JacobMiller-wd7vx7 ай бұрын
Was there a second torque after the initial torque at 48in/lbs?
@carlosmayorca46426 ай бұрын
You are the best!
@rickfingermancfp12393 жыл бұрын
Awesome job! Not fun but the prep is most important part of the job
@1AAuto3 жыл бұрын
+Rick Fingerman, CFP Thanks for the feedback!
@chieflouie28213 жыл бұрын
Why do AT pans have rubber/felt gaskets but oil pans have gasket makers (fipg)?
@zolof9114 жыл бұрын
Tip: Watch the video all the way through before you start! Don't remove the insulator by pulling on it as shown at time 7:40. Once you remove the cover of the flywheel, the insulator slides off of the two posts. At time 17:30, he talks about this. Anyone know what the part number for this insulator is? On my 95 coupe, I did not need to disconnect the exhaust pipe to get the pan out. I found it more effective to tap downward on the lip of the pan at the front of the engine with a large pry bar in order to separate it from the engine.
@prodigeemd Жыл бұрын
Is this the same steps for the V6 engine?
@JaidenStylezTV6 жыл бұрын
so what can i do if when i installed the exhaust back together and it start to leak?
@aarondensmore70836 жыл бұрын
Hey I’m looking under my camry, it’s a 98 and it looks like the dust cover or insulation plate that you called it in the video needs to be replaced. Do you have a part number or a more detailed description of what it is? Thanks
@1AAuto6 жыл бұрын
+Aaron Densmore We currently do not carry this particular part. Thank you for asking.
@JohnJones19876 жыл бұрын
There's a big gear under that thing - i'm guessing the fly wheel to the transmission? Anyway, my camry is a bit dirtier than your beautiful show model! But i'm not sure if i should clean that area up with some brake fluid cleaner, or just leave it alone. Unlike the oil pan, this cover doesn't seem to do much... i might make things worse...
@Ionlyexistpardner.2 жыл бұрын
How many hours spent on this job? And what is the name of the gasket sealer.
@imeralvarez53 жыл бұрын
I have a gasket I was told to put in, instead of just the adhesive you spread out, would it be a bad idea to put the gasket and use "the right stuff" to keep them together?
@phantomgaming81372 жыл бұрын
The haynes manual says to use both but after watching this video and reading through forums I'm going to just use rtv
@FaisalAhmed-kf9yf3 жыл бұрын
whats the time between finish seal and start drive the car ?
@djalal23277 жыл бұрын
how did you get the rest of the bolts off for the dust cover from the back side of the oil pan? size on those blots?
@shhway45903 жыл бұрын
What’s the cross reference or part number for the 10mm bolts for the oil pan ?
@nealseamon86247 жыл бұрын
its my car thank you im down to hitting pan with rubber malit not dropping ill keep hitting are there any other trix im going to take oil filter off mybe relece some presure
@dgreatll7 жыл бұрын
Neal Seamon Pressure should've relieved itself after draining oil from drain plug...
@gfriedman996 жыл бұрын
You need to cut through the old gasket to break the seal. You can use a stiff putty knife or razor blade.
@larryggoldman5125 жыл бұрын
When I took the tailpipe down and removed the gasket between the two triangular pipes. I accidentally tossed it out thinking I could get a new replacement easily. But it hasn’t been as simple as you’d think. The parts house don’t seem to have the ceramic gasket in the correct diameter. Can your company send me the exact right size that fits inside the two triangle exhaust plates where we removed the stud bolts? Need ASAP!
@phantomgaming81372 жыл бұрын
Autozone has them, just purchased P#60906
@ohtanner2 жыл бұрын
thank you!!!
@Kit2Kay7 жыл бұрын
is it ok to use a regular oil pan gasket
@1AAuto7 жыл бұрын
+Kit2Kay Yes you can use an oil pan gasket for this oil pan. Thanks for asking. 1aauto.com
@pablogon982 жыл бұрын
This is an excellent video, I'll have to do it in a Corolla and it is not as bad engineered as that Camry hahaha. Thanks for uploading Also #Chrisfix'sArmy here: Don't use a metal tool to scrape the gasket on any surface, you could mess it up. Better to use a plastic scraper or a scotch brite abrasive sponge. PD: IDK about you but my next YT suggestion is named "How to PROPERLY use RTV to make a gasket" by Chris Fix. Go check it out.
@thomassmith20566 жыл бұрын
amazing video 😁
@kadenbatterman52885 жыл бұрын
Should be the same steps for a 5sfe mr2 right same motor
@calebproductions59703 жыл бұрын
Is there a vid for doing this on an 04 Camry?
@1AAuto3 жыл бұрын
+caleb productions We do not have a video for this repair right now, but we'll keep this request in mind for a future video! 1aau.to/m/Shop-1AAuto-c
@_baller5 жыл бұрын
Never seen anyone spread the on the pan...not sure that's a great idea
@jasonduarte956 жыл бұрын
One of the oil pan bolts broke, what size are they?
@1AAuto6 жыл бұрын
+jason duarte Your local dealer should be able to get the correct size for you. Hope this helps you out.
@lotusbomb75946 жыл бұрын
How much would this cost to fix +labor??
@barryf54795 жыл бұрын
Just had one done today. $522. They billed me 3.5 hour's labor. Frankly, I'm glad I had it done. Having a lift makes it a lot easier and doing it on ramps would be a real pain. Great video. Very professional.
@billytadlock97923 жыл бұрын
Did he remove the skid plate
@1AAuto3 жыл бұрын
+Billy Tadlock This vehicle did not have a skid plate here but if your does it will need to be removed to access the oil pans.
@billytadlock97923 жыл бұрын
@@1AAuto so I'm working on the exact same car right actually I'm doing the water pump but I figured fuck it when I'm down there I might as well drop the oil pan and fix the leak would you recommend that I take the skid plate off
@nihonkokusai4 жыл бұрын
That downpipe can be replaced aswell
@จักรพงษ์สุครีพ-ฐ6ธ4 жыл бұрын
สุดยอด
@1AAuto4 жыл бұрын
+จักรพงษ์ สุครีพ Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
@carlotv12122 ай бұрын
Did I miss the part where they used a mallet ?
@debbiequintal41772 жыл бұрын
Wonder why this man does NOT wear safety eyeglasses to protect his precious eyes
@850are23 жыл бұрын
What about a v6 tatorial?
@1AAuto3 жыл бұрын
+850 ARE We're always cycling through common cars. We'll add this repair to our list! 1aau.to/m/Shop-1AAuto-c
@reviewsunboxings128 жыл бұрын
That oil pan looks fine. I see no rust.
@1AAuto8 жыл бұрын
It's hard to see from the video, but there was a small crack in the bottom of the pan that was causing a leak. 1aauto.com?KZbin&CTA%20Comment&ATony 866-403-3393
@davidquillard31387 жыл бұрын
1A Auto Parts car repair videos
@davidquillard31387 жыл бұрын
1A Auto Parts car repair videos on KZbin
@gfriedman996 жыл бұрын
These pans are steel. Up north they will rust thru in 15 to 20 years.
@gregorymcspadden81645 жыл бұрын
i would hire you as we all know a lot of mechanics will leave bolts in there pockets and do a half ass job and yes i say most mechanics and just to bad for you mechanics that do that kind of shit work because you are shit ya you don't go through life short changing work ethic man just look at this guy a true HONEST mechanic
@richardeckley80383 ай бұрын
☺️
@JamesBrown-hv1xu Жыл бұрын
Kazoontight
@kimchee94112 Жыл бұрын
Toyota makes maintenance so complicated and time consuming with a lot of cursing working upside down on the ground. What's wrong with a single regular gasket? Using this glue will make it more difficult to remove and clean the pan next time. My 2000 V6 Camry is nothing like this, the trans and engine oil pans are located in flip/flop positions.
@poolpoolification2 жыл бұрын
no gasket? hello? theYmake a GASKET FOR THIS CAR
@nealseamon86247 жыл бұрын
pan is not dropping anyone have thoughts help please
@gfriedman996 жыл бұрын
Neal Seamon try a pry bar or screwdriver to wedge it apart.
@iMMoRTalxm6 жыл бұрын
Don’t use a pry bar you will dent it and loose shape of the sealing. Use a rubber mallet they are like 4$ at autoparts
@genericusername13655 жыл бұрын
Tap a plastic putty knife it there to break up the old seal. You could use a metal one or a razor blad if you are very careful not to put scratches/cuts in the metal.
@petergaudet20313 жыл бұрын
No safety glasses!
@1AAuto3 жыл бұрын
+Peter Gaudet Thanks for the feedback!
@Sly_Mango6 жыл бұрын
Well done! but please wear safety glasses.
@JacobMiller-wd7vx7 ай бұрын
Was there a second torque after the initial 48in/lbs?