Best Toys Jeep Wellye control repair

[@gamingwiththegrangers]

All commenters, these boards are 12v you put more in their going to pop.. check the wellye range of boards there’s a few.. best one at 12v is the rx37 - 12v supports up to 200w so you can add high powered 35000rpm motors and it won’t burn it up.. just make sure you check the connections are the same as yours then it’s literally plug and play.. I went for the rx30 - 24v.. I’m running 2 12v battery’s in series so 24v.. and I’ve had to upgrade my motors to 24v @30000rpm otherwise they will burn out abit to fast for my liking.. Anyway stop overloading these 12v boards.. upgrade it..

[@gamingwiththegrangers]

Oh and sub and like from me🙂

[@1empyre1life]

Thanks for the like/sub! Your comment is probably the best one so far, super helpful!

[@gamingwiththegrangers]

No problem 🙂 yes took me ages to figure out the best and easiest way of doing it couldn’t find any vids.. and keeping parent controls. Hope this helps

[@duck42069]

Gaming With The Grangers’ what is the extra plug for on the Rx-37, the ride on toy only has 2 plugs and the receiver has 3.

[@Jarosegolf]

Upgraded my sons Jeep to 24v. Any idea why it will not sustain 24v power? Seems to revert to less than original 12v. New batteries, hooked up in series with same amp. New circuit board, and motors for rear. What am I missing? Figured it doesn't hurt to ask in case you might know the answer. Thank you.

[@jareau]

Thanks for this. Just over volted my kiddos Jeep a few hours ago. It's 11pm and I'm in bed in the dark searching the internets for a solution and found your video. Exactly what I needed. Thanks dude.

[@1empyre1life]

I'm glad to help! Thanks for the comment! Hopefully you read the others

[@adub1440]

I was looking for this exact video, and you did it. Thank you bro

[@joemork5048]

And I connected it backwards or somehow wrong and my whatever those things are exploded, but when I replaced mine, and I hooked up the battery the right way it worked just fine except for my steering is not working. I think it’s because the little chip next to that transformer or whatever it might be Was kind of melted when I was trying to solder it the other part in.

[@airgunningyup]

any tricks to syncing the old remote with the new controller??

[@codycharmley7154]

Thank you this was exactly the video I needed! Very helpful 👍🏻

[@MrGeekrick1]

You are the only video on this and I am looking for a replacement. I am currently attempting to repair and modify a board to accept a 19.4volt drill battery.

[@1empyre1life]

MrGeekrick1 if you know your electronics, you could certainly do it. I think a motor upgrade would be good as well. That's basically what I used and blew it. It did run for a few charges on the low quality original board..

[@gamingwiththegrangers]

MrGeekrick1 search eBay or amazon for wellye rx30-24v I run mine at 24v works fine, I’m not sure but I think it needs to be running at 24v to run tho.. In your case and the guy in the vid.. I would get the rx37 12v board it supports up to 200w so would support 12v 35000prm motors

[@franciscoescareno8588]

Gaming With The Grangers’ im planning on buy the rx-30 24v circuit board but my little jeep has a radio and some led lights , do you know if they will still work with 24v circuit board ? What other modifications need to be done be sides circuit board upgrade? Ill apprecciate any info you can share with me, thanks in advance

[@allstarshootinguk3222]

@@franciscoescareno8588 we tried running 2x12 volt batteries yesterday and it blew so we ordered the RX 30 24 volt which is coming in a a week. We put the old 1 back in Jeep works fine but now no lights and sounds??? Any ideas anyone

[@joemork5048]

I have the Same ride on toy and I was putting a different battery in it

[@1empyre1life]

Replacement board: amzn.to/3JC8Ob7 Make sure to confirm you have the same pin setup/number when you order This seller is not the same as the one in the video.

[@MrInstag8tor]

Could I upgrade to the 24v board they offer and it still work with the upgraded battery. Not worried about the motors

[@1empyre1life]

@@MrInstag8tor That's a question many people have. I suspect that it will work. Please let us know how it goes if you do!

[@samueleverett3719]

I did the battery upgrade and blew the same capacitor too. I replaced the board but the steering no longer works….help please

[@anthonyvanover8751]

I've just got a quick question I'm really hoping to get answered here. My question is once the relay is fried is it possible to bypass it by running wiring from battery to shift then to foot switch and then to motors? Or is buying the replacement board my only option

[@sekiro5982]

yes it is possible because the box is actually here only for the remote to work, you just need to correctly wire the pedal and forward / back switch to the motor and battery

[@stefanmeyers2808]

@@sekiro5982 I'm thinking of putting a double pole double throw (DPDT) 3 position switch inline with the gas pedal, it will give me forward and reverse. I will upgrade the wiring because at present it only has thick wires from the Wellye board to the wheel motors. The 2 brown wires to the gas pedal are thin and so are the wires from the battery. My board burnt, and the red and black wires fused together, not heavy enough gauge wire.

[@tarafaithnicole4621]

​​@@sekiro5982 hi I have a 12v best choice car and it seems that the module has some damage to it since my lil girl doesn't need the remote any longer and I'm just wanting the car to work is there a way to bypass the modular altogether? Any advice is greatly appreciated. #justamothertryntogetmylilgirlscarworkinagain

[@JAG77productions]

Exactly what happened to mine. Did the new one let you use the 18vlt battery ?

[@1empyre1life]

I have not tried the 18v with the new part because the components have the same voltage rating, which means they could still fail. The beefier components can probably handle more current. If you have success with the new board and 18v, I'd love to hear back. Thanks for the question!

[@mohammedabdullah7826]

Hello, I have a trouble in SF and SB not work I check all wires and switches

[@sapnab5646]

i had an issue on my 6v rx57 where the steering could not be controlled by the remote. I purchased a 24v rx30 and i just get lights , no motor working, no sync with controller and no motorized steering from controller. any idea what the issue could be?

[@skyramanna9124]

Not sure why you had to try replacing a 6V rx57 with 24v rx30.. as per my quick look at the specs, the 1st one is 6 volts battery driven, while second one operates at 24 volts.. so its quite possible that the controller is not able to work with 6 volts (assuming you are still using a 6volts battery).. changing the battery to 24 volts also wont help, because the original motor is rated only 6volts. You may want to look for like to like replacement (with 6volt controller)

[@Cakefactory341]

Hey mate, you asked about why, after replacing the resister it still wouldn't work? I'm betting its because other parts are fried. Like you said, the boards are pretty sensitive, so that much current going over a board designed for 12v is probably going to suffer in many areas. Just a guess.

[@1empyre1life]

Hey, it's been a few years since I made this video, and I have since learned a bit more from viewer comments like yourself!

[@me59664]

My remote wont sync so do you know if the control box would be problem..everything else works n drives just not the parents remote

[@1empyre1life]

It could be the control box, or the remote itself. It could even be as simple as dead batteries in the remote. The last time I checked ebay, you could get a remote and main box combo for a better price than either component individually. My toy has died again but I haven't had time to try fixing it.

[@anthonyvanover8751]

@@1empyre1life I was wondering if you'd seen my question about the fried relay and if rewiring and bypassing the board was a possibility

[@AirWreckD]

The relay in mine burnt up..I'm going to replace them with regular heavy duty automotive relays and see if It works

[@kathikappal4870]

My relay burnt up how to buy new and where it is available

[@jeffmortenson5336]

Thank you for the video I have a slightly different toy I believe as our remotes are not similar, but I have taken apart my control board and it looks exactly like the your original does. Mine however shows no damage as the capacitor is completely intact, I don’t see any other areas where damage occurred either. My problem I’m having with the toy is that power comes on but the peddle and remote will not make the toy go. I checked to make sure the motors on the wheels are still working by placing the wires directly to the battery and then they work. So my only problem is the toy will not go when the peddle is pushed or the remote is used do you have any ideas what could be the problem?

[@1empyre1life]

It could be the MOSFETs or relays. I suspect the bad board in my video had blown relays (the big square black boxes) as well as the blown capacitor.

[@Nataleyshepherd]

I know this was from a year ago but this is exactly what mine is doing, i replaced the battery and the lights and sounds come on but won’t move when I push the pedal. Did you find a fix? Did you replace the circuit board?

[@liftedtoy97]

@@Nataleyshepherd Same problem here. Any luck?

[@stefanmeyers2808]

@@1empyre1life Run two leads from the red and battery terminals to the thick power wires that go to the rear wheels and see if the motors run the wheels ok.

[@garrenbutcher7154]

Can anyone help me?! I bought this new board and the 7 pin connector doesn’t line up quite right so im not getting a solid connection 😭

[@profit6268]

It made a popping noise when u knew it was crap ? Just ordered a new one and I believe cause me and my son where battling for control me on remote him on pedal it blew out ?

[@1empyre1life]

Yes it popped like a plastic bubble wrap bubble. I hope your repair goes well!

[@luiscontreras7690]

Where do you download the wire diagram

[@Yuvi2117]

I was using the 20v dewalt battery just fine until I tried to run 36v. Then it broke

[@mattyg7143]

Is the rx30 24v a straight swap for the rx7 12v? It looks like it has an extra set of plugs that go into it? Also do we know of running an 18v battery will power the 24v board?

[@1empyre1life]

Those are great questions! I'm not sure but hopefully someone on here does have the answer.

[@englandrasmussen3111]

Yes 18v works on 24v Weelye. I was actually able to run the controller and 12v motors 2drive + 1steer until the battery measured at 11.5V. That means you can likely run the rx30 for a little bit with a 12V battery. I am currently checking out how to change the speed setting more drastically on the controller (possible resistor that sets the speed reduction setpoints).

[@jakepeake6149]

So I did the same thing and replaced the box with the exact same rx23 box. Plug it in and I get no power. My old one turns the jeep on but it will not drive forward or reverse. Do you think I got a defective box?

[@1empyre1life]

Thanks for the question. A defective box is certainly a possibility. Maybe some other component/components were damaged as well. Feel free to post a follow up if you solve the problem!

[@paranormalcyclist0428]

I cannot connect the remote. How to fix?

[@hammadarif3441]

Can you send me wiring diagram link for this particular device in the video I have to commission this in my new car?

[@zedrickpowell5167]

I did the same thing and I replaced the box but now when I put it in gear it takes off without pushing the pedal any ideas

[@Archangel454]

Hey guys I have a power wheels and it was working fine but it stopped working all of a sudden. Idk if I overcharged it because I did leave it charged for awhile and it stopped working. I press the power button but it doesn't turn on. It only kind of turns on when I move the steering wheel back and forth

[@1empyre1life]

Check the electrical connections. Also check the battery voltage.

[@mattsmith3001]

Converted 2 12v batteries to 24v on my daughters jeep and same thing happened, made a loud pop and blew the same capacitors. I can order the replacement via amazon but my issue it that I still want to run 24v to speed it up. Any ideas so I don’t repeat lol?

[@1empyre1life]

I'm not an electronics expert, but I know you'd have to at least upgrade the capacitors and relays and probably other stuff too to handle the extra volts. You can go crazy from there like new motors, wiring, etc

[@jjc6776]

Matt same thing happened to me to a t. Ever come up with a solution? Trying to use my 18v drill battery

[@gamingwiththegrangers]

Buy wellye rx30 24v board problem solved

[@a.n.6351]

@@gamingwiththegrangers Same thing happened to my son ride on its a 4x4 jeep tried to upgrade the battery to a bigger it worked and it can go longer Then i tried to add more power by connecting another battery in series that when i blew up the capacitor even though i replaced it (hopefully it's in the correct way +-) but every time i turn the car on it start to go forward on it's own immediately any ideas why or just get a replacement board amd get it done Thank you

[@rajkumarsac]

12 v battery jeep ,After 10 to 15 min ride, my jeep is move slow, motor is getting heat, please give me solution

[@arpavlic03]

Hello. I am looking at experimenting with the Bluetooth receiver found in a similar Ride-On vehicle to see if it can be a discoverable bluetooth device for other electronics to pick up rather than restricted to the remote control. Do you have any knowledge as to how I can find the module on the motherboard or how I can find the Bluetooth address that is used to pair the two components? Thanks. Very helpful video

[@1empyre1life]

That sounds very interesting, unfortunately I am not versed in either of those skills. I would also like to know how to do that, though.

[@whatamericamademe]

so I have a question man cause I put 2 12 volt batteries in a Uenjoy 2 rider car and smoke started coming from behind the radio. Did your steering go out? if so maybe that is all I have to replace. I stopped the car before anything blew. I took out the control board that was behind the radio but maybe its that box you replaced that I really need to get switched out. So once again im asking you. was it the steering that went out?

[@hardcoreorganization]

What is the MOSFET on new part?

[@1empyre1life]

I don't have the unit anymore so unfortunately I can't say. Thanks for the question!

[@justinjuarez1852]

I ordered a replacement for mine can you attach a photo showing whats the receiver. I don't think the new motherboard i ordered is pairing with the remote because the receiver isn't compatible and I wanna swap them. Can anybody help and point out whats the receiver

[@sr8shoota]

Anyone know what specs are correct that cap that blew?

[@kcravi]

My son's car seem to have the exact controller box. The car started to have a problem since past week, it goes for around a meter or so and suddenly cuts out and starts again. He is driving on a flat ground. Tried driving with the remote control and it does the same. Do you think the controller can cause this particular issue ?

[@stacyskipworth]

I have this same issue. Drives for 2-3 minutes. Then cuts out for 30 seconds or so and starts itself back up. Anyone know if this is a circuit board issue?

[@corbinbeamer7007]

Did you guys have any luck fixing the issue or buying the part and that fixing it? My sons jeep does the same. Goes a few feet and dies. Then you restart and does same over and over

[@corbinbeamer7007]

Update: The new relay did not fix the shirting out/dying issues after several feet of driving.

[@SuperClown1979]

Got the same issue... Rides 2 meters and shut off.. Any ideas?

[@corbinbeamer7007]

SuperClown1979 I gave up and bought a peg perigo. I’m guessing it is a wheel motor short circuiting the unit or something. Kidswheels.com has all sorts of extra parts for these to tinker around on. but I didn’t want to sink more money into an unknown issue.

[@cameroncox8444]

Hey man I'm trying to upgrade my sons to the 18v and am having issues getting it right. Could you possibly post a video of how you wired it

[@1empyre1life]

Sorry for the late reply, but I went back to 12v. You have to either bypass the board and directly wire the pedal to the motors or find a way to upgrade the relays and probably capacitors and possibly other/all components to handle the extra voltage/current.

[@gomathisanthosh8748]

I want this product black box

[@pawanmavar3019]

Dear sir kya without welllye controler ke bina direct chala sakte h koi falt to nhi hoga. Or wellye control box ko kaise chech kre ki ye shi h ya nhi. Plz about me.

[@prorican69]

If anyone can help. If my sons 12volt quad was kept out in heavy rain would this part prevent the quad from starting? I replaced battery and it still won't turn on.

[@1empyre1life]

Check the battery voltage first. If the battery is good, check this part. If something is wrong, it might be something you visually identify, but maybe not, so replacing it could fix the issue

[@prorican69]

@@1empyre1life Thanks for the response

[@IG_Gh0st3]

Will this motherboard (being blown) cause the vehicle to turn on but not move/pair with controller? I am trying to do the process of elimination with my sons urus ride toy. The battery seems to be working fine. But I did charge it for like 20 hours and that might have caused the overload. But it starts and the lights, radio/blue tooth are functioning correctly. Any feedback? It’s greatly appreciated

[@1empyre1life]

That's a good question, hopefully the answer lies in the comments somewhere. The radio or Bluetooth did not function, as well as the driver controls when mine blew. Hopefully this helps!

[@charleesol3374]

Hi, my son's jeep makes noises and the lights flick, it doesn't makes anything, just stopped working, i always used the original charger, any suggestions?

[@1empyre1life]

It could be a wiring problem. I think the lights and sounds are on a different circuit board, and that could be faulty.

[@nayitocota7665]

Do i need to buy the remote for it or can i connect the one i have

[@1empyre1life]

nayito cota you can use the existing remote. You will just have to sync it with the new board

[@drewstein8847]

Is there a way to make the best choice jeep use a dewalt 20 volt battery? I hate charging for 14 hours on the off chance my daughter will use the jeep the next day when I have half a dozen dewalt batteries laying around the garage.

[@1empyre1life]

Without giving it too much thought, I'd recommend looking into using a buck converter to step down the voltage to 13 or 14V (maybe more if you're feeling lucky) and ride into the sunset with those DeWalt 20Vs. If you wire them directly, you will probably fry the electronics like I did twice and end up giving away the jeep.

[@ronkloiber]

Do you have a schematic for this controller?

[@1empyre1life]

I do not. Thanks for the comment though, and if you do find a schematic, I'm sure others are interested.

[@ronkloiber]

@@1empyre1life thanks. I have the black version and there is 1 unused pin of the 7. It's the 3rd pin closest to the short edge. Wondering what it's for and if I can use it for something. Would be cool if I could beep the horn or switch music etc remotely. My car has 3 speeds controlled by the remote, and has the gradual acceleration feature. Would appreciate If anyone knows what these pins are. Thanks.

[@rickii2010]

Hey my kids Jeep has a broken blue wire coming from the small circuit board over the on/off switch can you tell me where that goes to? I look but can’t find where it suppose to go. Thanks in advance.

[@diegoflores8339]

That's just an antenna for the radio. One end does not connect to anything

[@rickii2010]

@@diegoflores8339 I was thinking that, thanks so much .

[@aurorablancaflor6521]

Is there anyway to fix that? I just got one on offer up and I saw a free blue wire down there

[@rickii2010]

@@aurorablancaflor6521 turns out that’s the wire for the wireless controller so it doesn’t connect to anything as far as I found out.

[@elchefe4770]

hello guys, someone can help me? i have the same board with blown capacitor but i don’t really know if is 6v or 12? 2 batteries 6v each, seems connected in parallel. i will like to replace the capacitor someone know which capacitor i need to buy?

[@diablocell]

I'm curious if anyone knows the part number for U3? It is the mosfet with the large heatsink from the board in the white box. I can read what appears to be "150N" but the rest of it is gone from damage. Is it the same 150N03A as shown on the other board (black box) in this video?

[@diablocell]

For anyone out there, Amazon has the entire controller box for about $15. I ordered one to help me fix the broken one. The new box I received has a different part for the U3 MOSFET. It is NCE30H10. You will only find this part on ebay from china. I have found a cross that I believe will work that part number is long, it's IPP80N06S2L07AKSA2. This part is on Mouser.com. I use this company every day at work. However, I don't think you'll get around ordering the steering driver IC RZ7889 from china. I am not able to find a cross for this one. Most motor driver ICs out there are more than 8 pins. The ones that are the correct package (SOIC8) are not rated for 3 amps like the RZ7889 is.

[@markzepeda6864]

I did the same thing to mine & I ordered the new Weeyle part but now the radio isn't working and remote wont sync. Any ideas?

[@1empyre1life]

My radio stopped working when the original board died and didn't get fixed with the new board. My guess is some sensitive electronics in the radio were somehow damaged.

[@markzepeda6864]

1empyre would you happen to know if they sale the radio chip online? Tried looking but no luck. I contacted the manufacturer and they haven't for back to me.

[@1empyre1life]

@@markzepeda6864 I did some searching for the radio chip but had no luck. I have an old car stereo that I might try hooking up and mounting somehow lol.

[@dmtmachineelves]

My car won't go forward on remote or gas pedal what's the fix

[@1empyre1life]

Troubleshoot. If it was just the gas pedal/wiring, the remote would probably work. Since they both don't work, it could be the electronics, which a board replacement could fix. It could be the relay that controls forward movement as mentioned in the video. If you know how, test the continuity of the depressed pedal. If it's good, then the likelihood of the circuit board being the problem is even higher. It could be something else, but if you test as much as you can and everything else checks out, get a new circuit board/box. Let me know how it goes!

[@dmtmachineelves]

@@1empyre1life yeah that's what it is. I noticed the Master switch went too so it's something in the circuit board

[@1empyre1life]

@@dmtmachineelves Hopefully a new board will fix it. Post a reply on your results!

[@dmtmachineelves]

@@1empyre1life will do thx

[@treebuster93]

I recently unplugged the middle cord of the 3 while my sons Jeep was charging. The Jeep won’t turn on now any suggestions

[@englandrasmussen3111]

Plug it back in !

[@Swataha]

My kids car is going only backward not going forward , any solution

[@1empyre1life]

Is this a new problem? It might be the wiring. Maybe in the switch to select forward or reverse. It could be electronic too

[@antonioreyes4413]

Can you provide a link where you got it

[@1empyre1life]

Search "Wellye 2.4" on ebay and you should get results. Make sure to get the right connector based on your existing board, ie 7 pins, or whatever. Apparently you can get them with a new controller, which appears to be cheaper currently. Here's an example link that will probably only work for a short while. rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fitm%2F173673709644

[@nukpulu510]

I've recently bought a Cosmic Overdrive SX118 Model Kids Car ride for my son. Works fine but my controller is now damaged. I've been looking all over for a replacement and all I can find is the Weelye controller from Amazon. Do you know if there is any way I can use this controller and transmitter to replace my old one?

[@1empyre1life]

There's a decent chance that would work. You can try getting the controller out and seeing if the pins and connectors match the wellye in my video. If it's not quite the same, there are other versions that might be the right fit.

[@yumytasty7729]

my car does not start , i want the starter card. Can you help me

[@sonnycollado3793]

how much pcb board

[@faimuddinbnic809]

Yeh kaise khariden

[@Amraks]

u2 could of blew, I have one on my work bench now. Could you tell me what u2 is? as this is damage is obvious. The person has hooked up the battery with the wrong polarity

[@Amraks]

from what I can read of this chip it was rz7889

[@1empyre1life]

Can you elaborate on what u2 is?

[@mikebarney]

U2 is a motor diver. It's what delivers power to the DC motors at the wheels

[@diablocell]

I realise this post is old but.. You are correct. U2 part number is RZ7889. It is the motor driver for the steering. I have the same problem, my nephew hooked up the battery backward and let the smoke out. I'm curious if anyone knows the part number for U3? It is the mosfet with the large heatsink. I can read what appears to be "150N" but the rest of it is gone from damage. Is it the same 150N03A as shown on the other board in this video?

[@youcefdjedid1829]

hello i have the same box and i need help

[@tonyjohnson3391]

What is the spec for the C7 capacitor?

[@1empyre1life]

16v 220uF

[@charntaerobinson7682]

My son jeep won’t charge does anyone know why this is happening?

[@customcreations-rickkramer5357]

Does anybody have ride on 4 wheeler (12v) that was working fine then radio and sounds stopped working. We have another one which everything stopped working including the motors. Only thing that worked was the power button (red light) and the headlights. The replacement had same issue right out of the box. Bought new control board and put it in the newer 4 wheeler and still no sound or radio. Drive motors still work along with headlights but that's it. . Please help if you know of any way to fix this

[@1empyre1life]

I believe the sounds are on a different circuit board. That could be the problem.

[@oscarprogamertime4504]

What is the specs of c16 capacitor? mine blew and i need to replace it

[@fastchevyracing87]

C16 should be 16v 220uF. Replacing with higher voltage rating is fine but must be 220uF

[@sauravsharma7158]

India May Require Controller

[@kbudagian]

Did you find out why the new replacement capacitor did not fix the problem? Maybe you installed the capacitor the wrong way around?

[@1empyre1life]

I tried several capacitors, installed both properly and reverse polarity. The relays, as suspected in the video, were damaged. There may have been other components damaged, but I couldn't find any other obvious damage.

[@kbudagian]

1empyre thanks so much for your reply. At least you tried. I will try to fix with new capacitors. If it don’t help, I will get a new controller. Stay safe

[@sr8shoota]

​@@1empyre1life can you let me know what size cap that is that blew

[@1empyre1life]

@@sr8shoota I'll see if I can find out but I don't have that toy anymore.

[@allstarshootinguk3222]

we tried running 2x12 volt batteries yesterday and it blew so we ordered the RX 30 24 volt which is coming in a a week. We put the old 1 back in Jeep works fine but now no lights and sounds??? Any ideas anyone

[@1empyre1life]

I lost the radio when I blew my board. I may have lost lights and other sounds, but don't remember, as it's been a while.

[@allstarshootinguk3222]

@@1empyre1life thank you very much for the reply do you think when our RX 30 24 volt comes they will come back on please

[@1empyre1life]

@@allstarshootinguk3222 you're welcome! Other comments on this video suggested that the new board doesn't fix the sound issue. I think it's a separate board.

[@allstarshootinguk3222]

@@1empyre1life is that the board where you charge it? Because our battery is full charge also but showing up flat red bar on the bit where all the buttons are the control panel and where you charge

[@1empyre1life]

@@allstarshootinguk3222 That's beyond my knowledge and experience on this matter, hopefully someone else can chime in and help!

[@umeshpatel-hs8mv]

C1 capacitor number

[@erdemilmenoglu636]

Yes bro which one near the relay 100v 4.7uf microphrad Another near the xo cristal is 220uf micropharad 16v

[@jgmshreya7649]

Steering ic number please

[@jgmshreya7649]

Fast mother board

[@venubabu6781]

Car restating run no move 12v indicetar 8v 6v down

[@StealPhantom]

What happened to myeen is plain bad luck, I upgraded. Was 6v went to 12v which isint even that high. The car works perfectly if driven manually. But my 2 year old cant ride it like that. The remote works for forward and backward, how ever it does not turn the wheels from remote.

[@1empyre1life]

Other people have had this problem, but I'm not sure what the cause or solution would be.

[@itexpert752]

Replace your heading word "repair" with "replacement".

[@SureshSharma-kw2bw]

Sent new one..i need

[@MrGeekrick1]

Discovered the relays need to be upgraded which would result in come ghetto looking stuff because the right ones will not fit. I pretty much need to reengineer the whole thing.

[@1empyre1life]

MrGeekrick1 yeah you could make it work, but it would take some work. It might be worth it because 18v is awesome

[@gamingwiththegrangers]

MrGeekrick1 get the wellye rx30 24v board and stick 2 12v battery’s in its awesome, had no problems

[@710amena]

Добрый день, вы можете написать название микросхемы на которые указываете пальцем на 2:19 минуте и под большим пальцем на 4:56 минуте. Эти микросхемы управляют рулевым колесом

[@martynwhiteside6737]

You didn't repair anything, wasted my time expecting you to show before and after repair and what components failed and how you tested and replaced them. 🤣

[@Nomipathan...]

When I connect battery kid car move auto....

[@1empyre1life]

Maybe the "gas" pedal switch is faulty. It could also be the circuit board, or something else

[@totanghosh3143]

Plz help me sir

[@1empyre1life]

What can I do to help?

[@royrajpurohit9331]

Kids jeep is working cannot of it by the key

[@sandeeptiwari1994]

Due to over load capacitor was blast.

[@bablukhan6239]

Very good video change to language to hindi please

[@milktoast6774]

Wish we could just delete the controller board. I don't need the controller. Just want to push gas and go

[@1empyre1life]

I hear you on that, it's definitely possible but it depends on what direction you want to go with the conversion because it will take a lot of rewiring and Hardware

[@djcampos123]

@@1empyre1life I’m ok with doing the re wiring and hard wiring just don’t know the proper way to reverse the motors to get forward and reverse.

[@youcefdjedid1829]

hello i have the same box and i need help