Max I really enjoyed the way you tackled this one.With your Video on the Micra K11 I was able to replace the Clutch on my car .That video was SO helpfull I thank you for giving me the confidence to do it. I have just ordered a Cordless impact wrench basic model chinese knock off for future projects.Can you tell me if the one you have is an adjustable torque type? I ask because I don't think the one I ordered is.I've never used one before and I am a little worried if the torque,rated at 420 NM is going to be safe to use on suspension bolts etc without snapping any bolts? Also would it be OK to tighten the bolts when they go back in with the Impact.Can the torque be varied on the cheaper versions by feathering the trigger ?I would welcome your advice before I undertake any more "ambitious" projects .Best Wishes always look forward to your uploads.M
@maxautouk Жыл бұрын
Hi Mark good to hear from you Impacts are best used for loosening, I tend to use mine for tightening a little but I always leave them sort of loose and tighten them up by hand and torque them down properly with a torque wrench!
@lovebajwa77342 ай бұрын
Mate my van clutch is too hard what should i do pickup is fine hard to shift the gear
@maxautouk2 ай бұрын
Disconnect the linkages and change gear by hand at the gearbox and see if its still really tough or not, could be a gearbox problem
@richardhawkins6034Ай бұрын
"Punch it out from the rear". I cannot get the longer drive shaft to budge. I've undone the 13mm bolt to open the clamp and I've tried putting a bar in where i took the first shaft out. I hit it, i even put my bottle jack between the bar and the back of the hub. Just pushed the engine and gearbox over on the mountings. What am i missing?
@maxautoukАй бұрын
Yeah they can get badly stuck, the answer is just to hammer on it until it comes out
@richardhawkins6034Ай бұрын
Turns out the answer was a pry bar beside the bracket with the 13mm bolt. No amount of hammering would have got it because there isn't a clear path through from the other side. Now both shafts are out, I can see something solid passing through the centre. What's got me now is the big wiring harness that covers the top bell housing bolts and I can't see how it's fixed on. One 10mm bolt on the left but can't see anything else!
@maxautoukАй бұрын
There is a stud too i think if i remember correctly
@FernandoDIY18 күн бұрын
hi thanks for the video. is there a part 2? would like to see seals replaced as well as putting gearbox back as its very heavy and on inclined .
@juandavidportillo2743 Жыл бұрын
Realmente hiciste un buen trabajo. Disfrute mucho viéndote saludos desde Argentina.
@maxautouk Жыл бұрын
Thanks 🎉👍🏽
@MytubeSPY6 ай бұрын
I’m struggling here, there doesn’t appear to be enough room between the gearbox and the subframe. How do I achieve enough clearance ? The gearbox is hanging on just the one engine mount and all ready to drop barring the bell housing bolts. Any help appreciated..
@maxautouk6 ай бұрын
Pry bar and force it out 😄 it is tight
@MytubeSPY6 ай бұрын
Ok, I’ll try, not sure how I’ll get it back in though 😂 I’m removing it to do the RMS. Thanks for the video though, it’s certainly helped me get this far.
@Felofelitto8 ай бұрын
Did you replace gearbox or only the clutch and flywheel.
@maxautouk8 ай бұрын
I just had a bad leak from the rear main seal and since it only takes half a day to do the entire thing I didn’t fit a new gearbox or clutch - but clutch and flywheel wouldn’t be a bad idea
@peterjohnson71488 ай бұрын
Fantastic job lad but you need to get one with doing the clutch and the seals etc that would have been a great part 2
@maxautouk7 ай бұрын
Aye it would have been thanks for the comment
@JacobSilverdal7 ай бұрын
Great video! This will help alot! Thank you very much 🙏
@maxautouk7 ай бұрын
Glad it helped!
@AndySwelly9 ай бұрын
Great video! What is the tightening torque for de driveshaft nuts?
@maxautouk9 ай бұрын
Hi there, it is 280nm!
@hermon92789 ай бұрын
Hello mate, where are you based? I’ve broken down I’ve got the exact same van, colour and year.
@maxautouk9 ай бұрын
I am currently based in County Fermanagh in Ireland! Are you mainland UK?
@hermon92789 ай бұрын
Yes unfortunately.
@maxautouk9 ай бұрын
@@hermon9278 what’s happened to your van?
@trennefelt11 ай бұрын
Thank you for this video. It helped me alot as I needed to change clutch and flywheel
@maxautouk11 ай бұрын
I’m glad the video was helpful and thanks for the comment!
@Felofelitto8 ай бұрын
Thanks for video i removed today the same gearbox.
@maxautouk8 ай бұрын
Glad the video helped! Hope you got on ok 👌🏽
@5e34nut Жыл бұрын
Did u chock the back wheels
@maxautouk Жыл бұрын
Nope I didn’t chock the rear wheels
@dalexfromeltd5013 Жыл бұрын
Very helpful thanks
@maxautouk Жыл бұрын
Thanks very much
@joshchadwick53496 ай бұрын
Hey is there a video with it being replaced and going back in
@usfiveandronniethecamper5 ай бұрын
Having trouble myself getting it back in doesnt seem to want to go in
@maxautouk5 ай бұрын
The rear end of the gearbox will hit the subframe, you need to moge yhe engine forward to get it to clear and the differential needs to go in the upwards position… sadly i didnt film refitting but i need to do the clutch soon so there will be a video eventually…
@redouanesahraoui51306 ай бұрын
c'est faux metter la cle a choc sur l'ecrou pas sur le premier boulon de la fusée pour ne pas endomager les dent de boulon