Can I use the agfrc programmer to give my piston pump “HOP” servo more juice? I’m using one for my hop servo, but it’s not really getting enough power to make it pop.Thanks OK I’m gonna!
@baezn884 ай бұрын
Thank you for the video.
@jevries4 ай бұрын
Your welcome!
@Baldheadnut17 күн бұрын
Where can I get that color bar lights that flash inside your cars PLEASE!! Thanks. Looks like they flashed to the music.
@jevries16 күн бұрын
@@Baldheadnut I custom made that one. I will look into having them made. They do flash to the music.
@Baldheadnut16 күн бұрын
@ yeah I’m sure people will jump on them especially me. I could use three right now.
@Baldheadnut21 күн бұрын
I have watched a few videos about installing the castle BEC in this case do we have to program it? Or just put it in. I have the 1080 Hobby wing ESC. So should I set it to 8.4 V?
@jevries18 күн бұрын
@kennethwilson2409 My SBEC has a jumper and 4 different settings 7.2, 8.4, 9 and 12V all manually selected
@dentman6216 күн бұрын
Set the hobbywing to 8.4
@Baldheadnut16 күн бұрын
@@dentman62 Thanks!
@Baldheadnut27 күн бұрын
Ok so with this set up how do you set the endpoints when one servo is inverted and you’re on one channel? Thanks!
@jevries27 күн бұрын
With servo USB programmer and software when needed. These SuperPumps don't need it though, just reverse and they are alligned.
@Baldheadnut27 күн бұрын
Ok thanks!
@Baldheadnut27 күн бұрын
Oh one other thing I was under the impression that the super pumps will fit in the same spot that the stock servos are? This is my first hop on a Monte Carlo. Or do I have to do to modification with the L shape aluminum piece? Also, do I need a BEC for each servo or just 1 since this is my first time trying this I’m mainly concentrating on the front concentrating on the front
@jevries26 күн бұрын
@@Baldheadnut Unfortunately the Monte chassis is not deisgned for hopping so there's quite a lot of modification needed to get the most out of it. Our BEC provides enough juice for 4 servos.
@MadeByVia204 ай бұрын
How do we tap the SBEC into a Deans battery connection along the he fly controller?
@jevries4 ай бұрын
I soldered mine together with ESC power cables to a Deans plug.
@davidm27784 ай бұрын
Awesome video…..
@jevries4 ай бұрын
Thanks!
@505bullys_N_Lowriders4 ай бұрын
Are the servos for hoping? If so how much are they?
@jevries4 ай бұрын
Yes, we custom developed these servos for hopping. You need to use a BEC and 3S lipo battery and use the first hole on the short servo horn to get 100% torque.
@szymonszewczyk82254 ай бұрын
@@jevriesnow that's super cool,,2 👍👍up..
@Baldheadnut18 күн бұрын
Ok 👍🏾
@Baldheadnut16 күн бұрын
Can you PLEASE!! do a video on the transmitter a step-by-step endpoints video? I know the left box is the low end and the right box is the high end, but I can’t figure out how to get from the left box to the right box it would really be helpful if you could do this for us who can’t quite figure out how to do this thank you
@dentman6215 күн бұрын
When your on the settings for each channel on end points just raise it or lower it while on in endpoints and it will move from side to side
@Baldheadnut15 күн бұрын
Ok I’ll give it a try THANKS!
@hansdenboef14634 ай бұрын
hoi is snap er niks van maar het ziet er cool uit groetjes.👍👍👍👍
@TheSpaceCoupe57Chevy23 күн бұрын
I see youre not cutting your red wire anymore lol youre welcome
@jevries22 күн бұрын
You only need to cut the red wire from the ESC when you juice your servo's through receiver with the BEC. This is a direct power setup for your servo's bypassing the receiver.
@Baldheadnut21 күн бұрын
@@jevries can I get away with connecting the BEC to the balance port lead instead of splicing? I have some extra 3s balance port plugs which would make it really easy thanks! And when are you gonna get some more super pumps in?
@jevries18 күн бұрын
@kennethwilson2409 I never tried it to be honest as I don't know if the thinner wires of the balance port are sufficient enough to run the power through.
@Baldheadnut18 күн бұрын
Yeah I didn’t think about that. Thanks for your answer.
@BaldheadnutКүн бұрын
@@jevries I know you say 8.4 is safe I guess I’m taking a risk having my BEC at 9 V.??