2 questions about the XTOOL D1 Pro Laser...

Рет қаралды 5,610

Күн бұрын

In this video, I will show the capability of the XTOOL D1 pro with a 40W diod laser head on it and how it can cut out veg tan leather.
Here is a link if you are interested in getting an XTOOL laser: goaff.pro/jcknphinaz
#xtool #lasercutting #leather

Пікірлер: 38

@iamroy5993 9 ай бұрын

Hey Jeremy… Something you can do to help your leather lay flat AND cut down on the smoke is wet your leather before you start your cut. If you have Light Burn you can take a picture of your paper template(s) and import them in. Run a trace on the image, and from there you can easily make any adjustments you need to.

@RedBeardOps 10 ай бұрын

Heck yeah! This is the main thing I use my laser for... or at least the most valuable things I do with it! 😅

@Simplelittlelife 10 ай бұрын

Right on buddy! It is so nice over cutting them out by hand👍

@iamroy5993 9 ай бұрын

I had been delivering my knives in recycled Amazon boxes. Now I use the laser to cut sliding boxes out of 3mm plywood, with my logo etched in the top…

@Lazywatchsmith 10 ай бұрын

Cool stuff. I cut my leather wet ,but then it gets smaller as it dry. But it is very flat. And you can also cut the holes for sewing with the laser.

@skeets6060 4 ай бұрын

Its nice to see a traveling man, doing what he enjoys, looks good Brother

@henkh8740 10 ай бұрын

I also cut the holes for stitching. Do them in the one side, copy an flip for the other side. Works really well

@ImprobableIron 9 ай бұрын

I do that too :) game changer! Perfect stitching every time

@dhotamis 7 ай бұрын

Ok so xtool 40w works cleanly on stitching holes as well?! That’s what I wanted to see as well.

@davidportersr 10 ай бұрын

I got the xtool 40w after watching your blade engraving video. I really like it and have used for engraving leather as well as engraving steel. Took a minute to figure out a way to get a good visible engraving on an acid washed blade but it does a great job on that too. Plus you made a good point, I now want to engrave everything. Great videos. Thanks

@domparadis2975 7 ай бұрын

Great video, thanks

@Simplelittlelife 7 ай бұрын

Thanks! And thank you for watching!

@SNACKS1414 10 ай бұрын

Awesome... I bet you could have it setup to do more than just cut... need to engrave a design in it. Maybe see if you can get it cut the stitch holes good luck

@Simplelittlelife 10 ай бұрын

Yeah I’ve done a few with it etching first and then cutting it out since filming this and I think the stitching holes will be next. That would end up saving a lot of time! Thanks for sharing ideas👍

@Nospheratorum 10 ай бұрын

I would recommend taking a photo of your paper template and use it as a canvas in your software and just trace along the lines on the paper. Easiest way to do it.

@gurk2k 9 ай бұрын

Very interesting video, I thought it would be much more problematic and more charred. You caught my interest with the etch on metal and cutting leather but also, you can do some really neat projects with just cutting funny things in paper, your test there was just too smooth and easy. Really good editing and explanation, all in all a really good and interesting videeo.

@duncangiel9564 10 ай бұрын

Have you checked out the Shaper Trace? Kickstarter should be shipping in a month or two but might be just what you need, put the knife in the frame take the picture and off set it to make the sheath

@ljekatt 10 ай бұрын

Thanks for another great video! Perhaps the laser could make you the stitching holes?

@Simplelittlelife 10 ай бұрын

You're welcome and thanks for watching! Yeah actually I remember (I think I remember correctly) @RedBeardOps actually cut out stitch holes with his XTool. I just need to get a little better at the design side and then I think I will start doing that as well. Cheers👍

@ImprobableIron 9 ай бұрын

@@Simplelittlelifehi, i cut out all the stitching holes with the xtool for my sheaths. There’s a leather worker on KZbin called make supply. He has a awesome vid on how to do stitching holes! It really is a game changer! Great vid, thanks!

@Sub-AmatuerNaturalist 10 ай бұрын

Have you tried etching handle materials? I used a 20 watt laser to etch a logo onto a peice of black canvas micarta. It had a good contrast but that was only becuase i did not take the shiny coat off of it first. Still... It could be an intersting rabbit hole.

@Melbourne-s4x 10 ай бұрын

Never going to beat a press and knife, so much more efficient and no smoke.

@Simplelittlelife 10 ай бұрын

Except when you don’t have one. Will the press and knife also etch your logo?

@jarodmorris611 8 ай бұрын

Probably others have said this, but with a laser, ONLY ever do veg tan leather. Many others (I've never tried it) have said non-veg tan chemicals used are bad, bad, very bad.

@akloot1 8 ай бұрын

So, you selling your old personalizer?

@joemisak7925 10 ай бұрын

Make leather circles for a leather buffing wheel lol

@jonbroadsword7572 10 ай бұрын

Smells like branding time at Simple Little Life Ranch. 😁

@Simplelittlelife 10 ай бұрын

Hahahaha! 😆👍

@mbmurphy777 10 ай бұрын

Will it smoke less if the leather is wet?

@Simplelittlelife 10 ай бұрын

I don’t think so. Wet or dry you’re burning leather. Probably worse due to the steam helping carry the stink.

@benchapman5247 10 ай бұрын

Will the 10W laser get through the leather as well?

@RedBeardOps 10 ай бұрын

I can vouch for a 20W doing it

@benchapman5247 10 ай бұрын

@@RedBeardOps I have a 10W and it does stainless engraving fine (not cutting anything yet) but dont want to buy the air pump and find that 10W struggles with leather. I am hoping it will be fine as is, the more powerful lasers are a bit too much to justify for the hobby just now.

@WildAcresFarms 10 ай бұрын

My 10W Ortur will cut 1/4” plywood. I make perhaps 12 medium speed passes to avoid charring it to death, but it’ll do it. A 20W is roughly three times faster at that task. But if a 10W will do ply that thick, it’ll surely cut leather for sheaths. Use Lightburn as your software so you can experiment with travel speed, laser power output, and number of passes in order to obtain a cleaner cut.

@benchapman5247 10 ай бұрын

@@WildAcresFarms Good to know thanks, I never trust the manufacturers claims. I have an Ortur (LM3) as well, havent cut anything but paper so far (need to organise air and smoke extraction)