I assembled my new electric meter so it ready for the Rural Electric Co-op to hang on my new transformer pole. When they come and extend the power out to my build site.
Пікірлер: 46
@kaylor876 күн бұрын
Thanks so much for the video! This is exactly what I was looking for. I just mounted one of these boxes to the outside of my house and wanted to make sure I was on the right track. Hope all is well, thanks again man!
@marcochavez9858 Жыл бұрын
I have the same panel I want to add an outlet outside but the place where the green screw goes does not have a hole on the back of the panel so the bars are already bonded??to neutral and ground above or they still need the green screw thanks
@Onry15 жыл бұрын
5 Minutes into the video, he finally starts the install...
@carlthornton3076 Жыл бұрын
Very Good!... #29 ✝ {11-29-2022}
@richot3052 жыл бұрын
do you have to upgrade the panel in your house to 200 amps also?
@rauloliveros5162 ай бұрын
Dude....are you a tire repair man, or an electrician. You are wasting peoples time with your tire story...........
@darkmauveshore4 ай бұрын
Dang your electric company is nice. I have to mount my own pole and breaker box
@BearStar14 жыл бұрын
I'm a Licensed Journeyman Electrician with over 52 years in the Trade specializing in Residential & Commercial Electrical Wiring & Maintenance. I have never used Aluminum Wiring for anything other than direct buried feeders underground a few times. I prefer using Copper Conductors for every thing . As a Retired Federal DOD Firefighter I have seen too many Structure Fires caused by Aluminum Conductors overheating !
@thomaswhitten25374 жыл бұрын
I was wondering about that. He didn't how long the wire was either. I hate guess work. I'm going to use copper. I used to work in Florida along the beach fronts and the aluminum did not hold up well at all.
@thomaswhitten25374 жыл бұрын
@@MISSINGYEARS I did watch your video but I'm not an electrician. The setup I just bought is identical to what's in this video. I'd hate to tell you something wrong and have the whole thing go up in flames. I'm just going to pay the money to have it done correctly and move on with the build. There will be plenty of other things to save a dollar on. The main electrical feed is not one of them. Besides, code for me would be different than code for you. Sorry, I would help if I knew how.
@theshop53318 ай бұрын
"too many", how many were of the wrong gauge, done correctly, sized correctly Au is fine
@johndavies29498 ай бұрын
No kidding. Spend a few bucks and install copper for the three wires coming down the mast.
@clutch7472 жыл бұрын
do you have a model # for this breaker panel? trying to buy the same one. Thanks!
@lancestrickland77503 жыл бұрын
Nolox is no longer required. I want to say it stopped in the 80s. Aluminum wire is now made with higher grade Aluminum which doesn't oxide anymore
@davidward31812 жыл бұрын
You will need a ground to your house panel envelope it is not your main
@LoganAddisMusic4 ай бұрын
Great video! Do you have to connect jumpers from the meter socket to the top of the 200amp breaker or are they already connected?
@CountryViewAcres4 ай бұрын
Already connected
@LoganAddisMusic4 ай бұрын
@@CountryViewAcres thanks so much for the reply! Going to buy one now
@johnmca56434 жыл бұрын
This is exactly what I'm looking for....I think. I want to mount this panel to my existing home. I want to use the existing weather head and support pipe. I want to install this panel, because I'd like to also bring wiring to my adjacent garage for basic outlets and lighting. I believe this will work.
@coryclark6906 жыл бұрын
That's actually a better and cheaper way to do your electrical you do not have to go out and buy a meter maid panel and buy a breaker box then you have to run one wire up to the top of the house and you don't have to run the bottom or air into the breaker box inside the house for this one you only have to run one wire and you're done feed your main lines in and you got power
@gtxccc35205 жыл бұрын
Cory Clark our company gave us the meter box we just had to pay for the breaker box
@HLBURDETTEFILMS4 жыл бұрын
Cory Clark nice work
@jamesreeves16722 жыл бұрын
Hi was wondering what type of wire you used for the metal conduit ?
@CountryViewAcres2 жыл бұрын
Most people use service entrance wire. I had some 4/0 aluminum wire I used.
@williamlanier98 ай бұрын
Wouldn't you have to have a ground wire and a neutral wire coming in from the house?
@johndavies29498 ай бұрын
Should be in the non metallic service entrance cable.
@kaylor876 күн бұрын
I believe, like John below said, the service wire that runs between the panel indoor and the meter main outside will have ground conductors inside. So you run the indoor grounds back outside to the meter main. Then I think you would want the main grounding electrode conductor that runs to the ground rods to come out of the meter main, rather than out of the indoor panel.
@TheLaidbackBiker Жыл бұрын
So who makes the box? Someone asked but no answer.
@CountryViewAcres Жыл бұрын
It is a Square D - Homeline meter/breaker box
@johnzink3309 Жыл бұрын
thx
@duckthis173 жыл бұрын
Good vid thank you.
@chickenhawkfarmstead84784 жыл бұрын
Whats the price of something like that.
@ibezag03 жыл бұрын
Contractor: 2500-5000 depending on length of dirt to dig up and placing schedule 40 pvc in the ground DIY: whole different conversation
@Ithinkimaybealesbian2 жыл бұрын
Now that we got the flat tire business out of the way
@1percentSolutions239 ай бұрын
Does it bring a bonding screw?
@kaylor876 күн бұрын
I'm about to use one of these boxes and was thinking about this earlier today too, but I think I maybe had a realization just a little bit ago... There is no green bonding screw because this is directly below the meter. Its the closest point physically possible to the meter, so this is always where the neutral and ground should be bonded. So there is no green screw giving you the option to bond or not -- the neutral bars, neutral lugs, ground lugs, and box chassis are all already bonded together. Right?? Makes sense to me anyway, and looking at my box, I do believe that's how its set up. So then when I run power back inside my house to the indoor panel, I'm going to throw that green screw far farrr away, not to be used, add separate ground bars into the case, and keep the ground wires all separate from the neutrals. I believe my main grounding wire to the ground rods will also come out of this meter main box outside, and the indoor panel will just have grounds come over to it through the service wire.
@jimmybrooks68644 жыл бұрын
What size Allen wrench does a breaker box takes
@ibezag03 жыл бұрын
150-225 amps typically 3/8s allen size
@angelRamirez-ru2ub4 жыл бұрын
Wat the name of the cable that goes from your meter to the house main box
@ibezag03 жыл бұрын
Load side conductors or feed to main breaker at the house
@zcharania2 жыл бұрын
Can you please share me the link to buy the mobile home feeder cable that you used in your video from the meter box to the main breaker box that is located in the manufactured home. Also share the link to buy the cable that you used from the meter box hub to the cable coming out of the weather head. Please and Thank you.
@Swampfox3214 жыл бұрын
A 7:30 video that should have been 2:00
@beccain81924 жыл бұрын
Half of video is about his tire and not finishing the box
@SgtTonybertram4 жыл бұрын
No ground wire coming in from weather head? In Alabama it is a requirement but what the hell is up with flat tire. Stupid video
@Nick-bh1fy4 жыл бұрын
There’s no ground that comes in from the transformer side. Neutral is grounded at that point so there’s no need to add another one, you bring a ground to ur main panel tho
@2015_Rubicnn2 жыл бұрын
Why in the hell would a weather head be grounded? You might as well ground the ground.....😂