Found some bad gears in the differential housing. Replaced them with parts from Advance Auto Parts.
Пікірлер: 277
@sedarianbloodsaw8 жыл бұрын
I usually don't comment but this video saved my life real talk I never did it before and people kept saying change the entire rear end on my 1999 silverado ibwas getting high 7-$1200 for a read end until I seen this video I went outside and changed it out with no problems this was my only vehicle getting to work with a lawn service on the side man I really appreciate it!!
@noahrobin69647 жыл бұрын
thinkbeforeuspeak was your rear end making a "popping" noise when you would turn from a low speed? I have a 2000 silverado and I'm trying to figure out what the problem is.
@bloosaw17 жыл бұрын
Noah Robin well it wasn't making any noise at first just felt like a slipping transmission,then woke to go to work and the drives haft was spinning inside the rear end
@LL.Johnson7 жыл бұрын
Noah, your spider gears/ or LSD is trashed. Just open your inspection cover on rear axle... Figure out what's busted and move forward. Should be busted spider gears though. I just developed the same problem with my 2000 Silverado. Only happens when I turn right at slow speed. I just hope there is no damage to the Ring & Pinion when I get in there to see what's happening.
@dontreply8987 жыл бұрын
T-1 same thing on my 2000 silverado and my spider gears are trashed up be working on that for a while bought a new car in the meantime
@Bird.Squawk5 жыл бұрын
To all other DIY video makers.....THIS is how it's done.. clear,to the point,great lighting.. A+ on this video!
@kevinsummers94494 жыл бұрын
Except he didnt how how yo reinstall ........ other than that yes i agree great video quality.
@zakadams80457 жыл бұрын
I own a 01 Chevy Suburban LT 1500 I'm running a corner this morning I hear a little grinding and then all the sudden at the Apex boom grind grind grind and immediately I knew something bad happened in the diff. so I baby it home luckily without any spider gears falling out and I bust open the cover and low and behold the actual shaft is sheared off and missing on one side and the other side is still in barely being held by its screw As a result of the other side being broken not sure how I did that but I did . I will be making a video to the same effect that I will upload and post a link to. thank you very much this was very helpful and you're editing / explaning skills are impeccable these kinds of videos are what makes KZbin so helpful thank you again
@7inKing6 жыл бұрын
After watching 4 different videos I’m glad I came across yours. Very well explained and I’m feeling pretty confident about doing this. Thanks a lot brother.
@hcastro688 жыл бұрын
Absolutely GREAT video! I'm doing my gears today.... Exact same problem. Thanks again and don't stop making videos. Very informative and detailed.
@LPORT5 жыл бұрын
Thank you for posting this video. My G80 gernaded, saw this video, ordered a new differential G80 for my Chevy Avalanche and did the install thanks to this video!
@joelcalvillo94874 жыл бұрын
That’s d way everyone should make videos where u can see d details close up n good lighting nice job man
@shonalex9 жыл бұрын
So happy I found this video. I think you just saved me about a thousand bucks!!! I was going to hire someone to do this for me, but since I think I'm just doing the spiders now, I'm going to try myself. My old Suburban has 150K miles, so I think it's probably time. Starting to make some noises in the back so I at least need to open it up and look. THANKS SO MUCH!!!
@JoDaddysGarage9 жыл бұрын
Shon Alexander I'm glad you found it as well. You're welcome.
@MuhNeh4 жыл бұрын
The way you pulled out the C-Clip almost mad me cry. I spent I good hour trying to get that sucker out, had to have someone push the axle in as hard as they could to have enough room to slide the c clip out. Awesome video though great lighting and explanation! Subscribed!
@milleslong65492 жыл бұрын
Absolutely amazing video! Very well explained! I was praying I would find a video like this because I too have never messed with the rear end and I was super nervous to get into it but knew no matter what I was going to try because I don't want to have to pay a mechanic to get this job done. I'm not 100% sure yet if it's just the bearings or if it's the spider gears but either way after watching this video I am confident I can get it done! Thank you for putting this together I greatly appreciate it :-)
@MichaelJones-nq5sb3 жыл бұрын
Thanks for showing how to put the gears back in the most important part of the video
@raterus7 жыл бұрын
I don't even have this problem (yet), but found the video explained things so well I watched it all anyway!
@JoDaddysGarage7 жыл бұрын
Thanks.
@ImaLoneWolfintheWoods9 жыл бұрын
I'm about to do this on a 2000 silverado, I had one hell of a time to find the right spiders, because my carrier is two large window, ordered at my local parts store and waited friggen 6 weeks to find out, they ordered wrong gearset. I finally got the right parts I ordered online. I found it was difficult cleaning out the metal dust flakes all out of the differential, but I think I'll run it for a little while and then do a fluid change to hopefully get rid of the rest of metal flakes. Thanks for the great video, up until this point I have never once opened up a differential, but I have rebuilt motors and transmissions and almost everything else. Changing these spiders is quite simple!
@JoDaddysGarage9 жыл бұрын
chris42000000 Sounds good. I have done a lot of other things, but I had not tackled a diff until this one.
@jaybud36467 жыл бұрын
Yes fluid change after putting on a few miles is a great idea! IMHO it's the final step in a complete and properly performed repair.
@carbonsteelbladetheorigina79936 жыл бұрын
You did a Great Job man! simple & good point outs! Not like everyone else putting the camera all around the world.
@davidfrank64375 жыл бұрын
Hi
@therubenchannel77923 жыл бұрын
Exactly what happened to my 03 Silverado yesterday! Im gonna tackle this project this weekend. Thanks
@Benny158L9 жыл бұрын
Hey Jo Thank You for the info I have a 2000 Yukon and just fixed it with your help Thanks good video
@georgegermain97735 жыл бұрын
I needed to see the line up on how to get them back in .Getting them out is not the problem!!
@MicroSoftner4 жыл бұрын
Me too, I watched the whole video right up until the end and no spider gear replacing lol
@ronh87173 жыл бұрын
I’m pretty sure that carrier has to be removed to get the gears in properly. Probably why he didn’t show that.
@sunflowerseed27517 жыл бұрын
You are gifted. Great control of the English language.
@JoDaddysGarage7 жыл бұрын
Thanks. That's a different comment for sure, but I appreciate it.
@siaripop77 жыл бұрын
Jo Daddy.....Really good video of the problem and fixes for it. In the comments Dee Money and T-1 seem to have outlined the problem I am having with my "92" Chevy 1500, plus I'm getting a vibration at highway speeds. I had it a month ago, then it disappeared, and now it has reappeared! Time to pop the cover and take a look. Again, great video!
@jasoneddy95159 жыл бұрын
I just bought my set at autozone for $107. Nothing against jo daddy, great video, glad i found it. But everyone should know they arent shims, they are thrust washers and yes you need them.
@JoDaddysGarage9 жыл бұрын
Jason Eddy Thanks for the comment. Glad you cleared that up. When I made the video, I couldn't remember the name, so I may have said shim.
@BernieMyersIII9 жыл бұрын
Nice video, glad to hear that i could get set from parts store. about 8yrs ago played hell to find. Got set for 99.99 autozone, awesome! ! 😆
@Sundance70558 жыл бұрын
hi JO.....I pulled my cover off today and my gears had 4 or 5 teeth missing....seems easy to me ....thanks for posting
@noedominguez82774 жыл бұрын
Thanks for the great info man I just did mines today went exactly how you said it would keep up the great vids‼
@mikecano11358 жыл бұрын
great video. gonna do my 96 tahoe this weekend. haven't opened it yet, hope it's just the spiders.
@nexus7tablet6107 жыл бұрын
The flat is for oil to get into the bearing surface
@kb3yourmom9128 жыл бұрын
alright thank you man really needed this info before I go being it to a rear end/differential shop
@tdalton5069 жыл бұрын
I have to replace the spiders on my 1994 suburban. Only bad part of breaking them is I have to drive a ford...
@jaybud36467 жыл бұрын
Haha! Something I'd say. Yet likely just walk.
@Flake1m7 жыл бұрын
thanks I'm gonna try this everyone keeps saying I need a new rear end for my 98 z71 but I think this is the problem and 2 other people said the same thing but I had no idea how to change the gears I just know how to put a new rear end in but this helped me alot
@ArmaAceChannel10 жыл бұрын
replace your gear oil at recommended mileage kids
@badmudderrutters74603 жыл бұрын
Very easy fix, usally caused by doing burnouts on turns.
@denigong97082 жыл бұрын
My rear end in my 2000 gmc looks just like that right now. I don't know how my truck moves even. Will be doing this same job in the next few days.. Yay
@Jan_Seidel9 жыл бұрын
The flattened parts of the shaft look to me like a support to get oil between shaft and gear to minimize wear and tear
@STgaming86125 жыл бұрын
Thanks for the video gonna tackle mine Wednesday it just pooped on my today I have set order at napa paid $130!
@Rudderify10 жыл бұрын
Great vid. Every little project that you video will surly help someone in The Garage Gang and beyond. Good stuff, Sir....now get back to the Mustang resto! Haha!
@JoDaddysGarage10 жыл бұрын
The Garage Gang. I like it! I know I already say gang in some videos. I'll have to work Garage Gang in there. Back to the Mustang on Monday!
@robertpaulis4393 жыл бұрын
Short, sweet and awesome!!! One great video.
@manuelpadilla22708 жыл бұрын
thanks bro u just saved me alot of money good video
@robertlewis45143 жыл бұрын
Very good directions keep up the good work.
@georgefelix79069 жыл бұрын
Don't get me wrong , but this differential has been in very bat mistreated , no mater 200k , in this case , replaced the all assemble is in my opinion , the most chip way to put the truck again on the road . Thank you for your video.
@neoramen19 жыл бұрын
This was very helpful. Thanks.
@joshb53739 жыл бұрын
Great video, thanks for posting.
@rafaelguzman54567 жыл бұрын
gracias muy completo tu vídeo ......me sirvió de mucho en el taller ....sigue subiendo mas ... :)
@jaybud36467 жыл бұрын
It's always a good idea to pull both axles completely out so to clean up/inspect the axle tubes/wheel bearings of filings/metal chunks and replace axle seals while doing so. Chances are some debris has worked it's way towards the wheels.
@JoDaddysGarage7 жыл бұрын
Good advice.
@jaybud36467 жыл бұрын
Especially with the extent of the destruction. Replacing mine in the next few days, few teeth broke but nothing like that, WOW! Never seen any as bad as those. Amazing to see the pinion and ring virtually undamaged. Enjoyed the video. You got a new sub.
@JoDaddysGarage7 жыл бұрын
Thanks.
@passthetunaporfavor8 жыл бұрын
Dude you are the man. Thank you.
@thomaslockley9455 жыл бұрын
great video I know its hard to record an work lol but really good video an explaining step by step
@chriswooley464710 жыл бұрын
I think this just might save my ass good CLEAN job!!!
@JoDaddysGarage10 жыл бұрын
Good. Glad I could help.
@petrocksgarage10 жыл бұрын
Great video. Very informative. I'm surprised the truck moved at all with the gears chewed up like that. With all that destruction and metal shavings, aren't you worried the shavings will get in the bearings and tear them up too (if it hadn't already)? Or did you clean them up before reinstalling?
@JoDaddysGarage10 жыл бұрын
I did not remove the bearings, but I did use a few cans of cleaner and a lot of shop towels cleaning it out. The owners have put a lot of miles on it, and have no issues.
@TheFred19527 жыл бұрын
I have a Silverado with the same problem they list two sets of spider gears for the 8.25 diff and another set for the larger diff
@jasoneddy95159 жыл бұрын
I did find out its easier to get the gears all lined up first the roll them back and slide the thrust washers in. Lol
@JavierGarcia-ge7yg3 жыл бұрын
Did you had issues with the shaft not turning when you were putting the pin in? Cause mine don't turn..I even tried it on neutral and nothing..
@stearnwill999 жыл бұрын
This Video was Amazing man
@ericpinter2910 жыл бұрын
Thanks this video saved me alot of time
@JoDaddysGarage10 жыл бұрын
ericpinter29 Glad to hear it. That's why I make them.
@MrLuisylupe9 жыл бұрын
Thanks for the help! Awesome
@LL.Johnson7 жыл бұрын
GM should have recalled this... My 2000 Silverado just had the spider gears fail at 84K Miles. I see the same problem all over the internet. Anywhere from 60K-200K.
@Davethewelder5 жыл бұрын
Thank you 🙏🏻 helped so much !!!
@Davethewelder5 жыл бұрын
Now if I change from a 3.23 diff to a 4.10 do I need to get a bigger pumpkin or will it fit
@jerseybamboogie9 жыл бұрын
Great video man.
@DogsBestFriend0077 жыл бұрын
There's no mention of the shims on the spider gears on the pinion shaft. How were you able to keep one spider and shim in place while rotating the carrier?
@JoDaddysGarage7 жыл бұрын
A little bit of oil if I remember correctly.
@bigmell62624 жыл бұрын
Just had this happen to my tahoe at 295xxx miles..
@abrahampena75908 жыл бұрын
This video helped replace those same exact spider gears with those same exact other new spider gears ... but found out that suburban was a 2 wheel drive and my sierra is a 4x4 will those gears affect my car while using my truck on 4 wheel drive ?
@JoDaddysGarage8 жыл бұрын
+Abraham Pena No reason they should. They do the same job as the old ones. The ratio is determined by the ring gear and pinion.
@JamesJohnson-kn8hc2 жыл бұрын
Question I have a 2002 surburban it clunks when I put it in reverse changed out both u joints what do u think only dies it when I put it in reverse not down the high way no play in the drive shaft either
@JoDaddysGarage2 жыл бұрын
It's very possible the gears are worn.
@carcrazycansgarage30737 жыл бұрын
Great video Jo . I have to do the same rebuild on my truck same year too and with 4.10 gears. Its funny I have owned 3/4 and 1 ton trucks all my life and never did a rear diff rebuild. I wonder why the gears go on the 1500 series ?
@JoDaddysGarage7 жыл бұрын
Hard to say. Maybe people are more aggressive with them.
@douglaselliott20678 жыл бұрын
Do you know what else is involved in replacing the spider gears in a limited slip differential?
@JoDaddysGarage8 жыл бұрын
+Douglas Elliott Sorry, I do not.
@brandonthompson16697 жыл бұрын
I am currently in the middle of this project on my o2 z71 and the pin that the 8mm bolt goes in is stuck in the carrier it only moves about an 1/4 of an inch either way. it won't come out. any suggestion on what to do.
@JoDaddysGarage7 жыл бұрын
That's odd. Not sure what to suggest.
@laredo130710 жыл бұрын
Did you end up using the shims for the larger rings? how do you know if you need them?
@JoDaddysGarage10 жыл бұрын
I used the shims that came with the new gears. I believe they have to have the shims.
@shanegambrazzio46297 жыл бұрын
Excellent video
@210exoticreptiles77 жыл бұрын
Hey Joe how did you get the carrier to move I have the rear end up still can't figure out how to get the carrier to move
@JoDaddysGarage7 жыл бұрын
May be a dumb question, but is the transmission in neutral? Or is the driveshaft unbolted?
@mharlan47 жыл бұрын
Jo I have the same situation going on ,only thing is I have a 4×4 suburban . but upon inspection of gears when I pulled them . there exactly the same as what these are . so I ordered some and the gear teeth ain't the same count ..my question being , is that will that hurt my transfer case when in four wheel because gear teeth are bigger ? thanks great vid
@JoDaddysGarage7 жыл бұрын
I actually had the same issue. The factory set had more teeth. It won't matter because you're installing them as a set. You're not changing the ring gear or pinion, just the internals.
@ogbsbutter34417 жыл бұрын
my center pin has a piece that surrounds it and pretty much makes my gears stay in exact spot how but can move and rotate everything how do i get gears out?
@JoDaddysGarage7 жыл бұрын
Not sure. Is it the same set-up as the one I did?
@mahmoodhameed42826 жыл бұрын
Thanks for the video 👌
@joeystephens28587 жыл бұрын
So tonight I was driving and hauling trailer and kept hearing metal on metal sounds and thought it was the trailer well was going up a hill and then heard a pop and metal on metal and my 01 suburban would not drive anymore. I could put it in gear and left off the brake and you could hear metal on metal and but the wheels were going. So put it on 4x4 and limped home. So by chance could this be what's wrong with mine before I go and purchase a whole new rear end
@JoDaddysGarage7 жыл бұрын
That sounds like the same thing. May want to pull the cover and see how bad it is.
@joeystephens28587 жыл бұрын
Figured lol So how safe would that be to continue driving till I can get it fixed
@JoDaddysGarage7 жыл бұрын
I wouldn't. If pieces break loose and bind up, it'll be like locking up your brakes....unexpectedly. Could be ugly.
@kevinsummers94494 жыл бұрын
Hey Joey Stevens. I have same problems just happened last night...... what was your outcome ??? Was it just spider gears? Thnx in advance
@donnyroland15092 жыл бұрын
Great Video. Thanks.
@therubenchannel77923 жыл бұрын
Hello, I discovered my Z71 has a mechanical locking differential I believe it's called. Would you know if the process for replacing the spider gears is the same as shown here?
@JoDaddysGarage3 жыл бұрын
I can't say for sure.
@lostnthought97807 жыл бұрын
in process of doing this now, need to turn carrier so I can get to lock pin bolt. what is best way to turn carrier?
@JoDaddysGarage7 жыл бұрын
Wheels off the ground, transmission in neutral. No parking brake.
@jayotto86227 жыл бұрын
This video is helpful to get my new gears on to my 2000 chevy tahoe but Im running into an issue. Was wondering if you could help? I cant get the small spider gear to get past the lip with the shim on it of where it sits on top. No issues with the bottom. Would you know how to get it past this lip? Can install without the shim but not with....
@JoDaddysGarage7 жыл бұрын
Hmm... Not sure on that one. What kit did you buy?
@jayotto86227 жыл бұрын
USA gear kit GM 8.6
@agentmacguyver29747 жыл бұрын
I have the same problem. My concern is that the carrier bearings or pinion bearing was bad if these were worn. But I REALLY don't want to take everything out and deal with shims and backlash adjustments etc! So, your video is exciting to me. How has this repair has held up? Any ongoing problems with bearings, etc?
@JoDaddysGarage7 жыл бұрын
Still in use and no problems.
@markbugley2919 жыл бұрын
Did you have to use the shims? What was the tolerance between the gears? Did you just use a feeler gauge to measure the tolerance or do you need a different measuring tool?
@JoDaddysGarage9 жыл бұрын
Mark Bugley I didn't use anything but what came in the gear set kit. The shims were already in there. I was surprised at how nice it fit. That was a concern I had, but I was told that it's different than if you pulled the carrier itself.
@ImaLoneWolfintheWoods9 жыл бұрын
I think as long as you are only removing the spiders, it is simple and won't require any measurements, but if you pull the carrier it can be a lot of precision work to make it right, the only thing I would want to take out carrier for would be to swap out the inner bearings, myself personally I am swapping only the spiders. Anything more and I would have to leave to the pros who are set up to fine tune the differential.
@MrOzzyosborne888 жыл бұрын
Great video man. my spider gears just went out on my blazer. this helps big time. what,and how did u get most of the metal shaving out?
@JoDaddysGarage8 жыл бұрын
+Stephen Osborne I used brake cleaner and shop towels. Kept rinsing everything down, and wiping it out.
@MrOzzyosborne888 жыл бұрын
Okay thanks man.
@cristiantoledo19624 жыл бұрын
How do you find out the size of your differntial when ordering the parts ?
@JoDaddysGarage4 жыл бұрын
Best to use the vin. I contacted the dealer. It may be on the data sheet/sticker.
@gossef28509 жыл бұрын
good work man, I got the same problem with the whole set of gears " the main gear got damaged and the spiders as well " chevy truck 80s 4X4. if you could possibly hit me with someone sells spare parts as what you got i will appreciate it. Good job again.
@JoDaddysGarage9 жыл бұрын
G ossef Thanks. I bought my parts at Advance Auto. You could try Rock Auto parts.com
@gossef28509 жыл бұрын
ok cool man .. thank you again.
@RealGraffz9 жыл бұрын
How long does it usually takes to replace them of you have the parts and tools?
@JoDaddysGarage9 жыл бұрын
If you know what you're doing and don't hit a snag, less than 4 hours. Probably 3.
@dylanhammond20628 жыл бұрын
how do you turn the carrier???? mine won't turn, o tried in neutral. my truck is in 4x4 so I could get it into my garage. I can't pull the pin out because it hits the casing
@JoDaddysGarage8 жыл бұрын
That's odd. Are both wheels off the ground? Paring brake released?
@dylanhammond20628 жыл бұрын
It was in 4x4 lol easy job great vid
@livinglifemyway73496 жыл бұрын
were you hearing a grinding noise, and did it get worse when you gave it more gas? I have a grinding noise and it gets louder when I give it more gas. Just wondering if that is my problem
@JoDaddysGarage6 жыл бұрын
Yes. It was grinding, but at this point, it was slipping internally.
@livinglifemyway73495 жыл бұрын
Thanks, I guess I need to pull the cover and take a look at mine.
@SuperGmann102 жыл бұрын
Good video. But I wish you would have shown it going back together. That was a little disappointing.
@xzx40205 жыл бұрын
Would this cause your truck to not move while in drive or reverse?
@JoDaddysGarage5 жыл бұрын
Possibly. But you need to see if the transmission is working first.
@dramahoe10 жыл бұрын
how did you put in the small gears in without having the washers slip off
@JoDaddysGarage10 жыл бұрын
Dramahoe I Don't really remember. I wish I was able to film that part. You can try to put a little wheel bearing grease on them so they stick to the gear.
@slicktrack61409 жыл бұрын
Jo Daddy's Garage Ya, that was the main reason I watched it. Good video. But just as you mentioned about how you got the spider gears set properly but didn't get it on film. I was bummed. I have to do that tomorrow.
@jaybud36467 жыл бұрын
80w90 them up some, they'll tend to stay stuck together.
@bubbabrown36983 жыл бұрын
But whats the best /easiest way to get the smaller gears back in
@Kennynva7 жыл бұрын
I think that spider pin is flat on two ends because the bolt that holds the pin in..has to go by it to tighten it...does this make since...
@JoDaddysGarage7 жыл бұрын
Could be....
@pimptydimp7 жыл бұрын
I believe its flattened to allow lubrication to enter that location better. Also, excellent vid i appreciate it. Same exact issue i just discovered this morning. Now to go wrench some more.
@tyrannyterminator41794 жыл бұрын
Good job!
@kb3yourmom9128 жыл бұрын
hey brother if you remember was the two little gears the same number of teeth or were they a different number I just got a set of Yukon gears spider gear set and the two little ones are one tooth in difference Idk if they packaged them wrong or what but the shop that was doing it couldn't get them in so I'm doing it myself... just was wondering if you have any feedback let me know asap t.i.a.
@JoDaddysGarage8 жыл бұрын
+Kelsey yourmom I would have to believe the tooth count would have to be identical.
@kb3yourmom9128 жыл бұрын
Alright
@noahrobin69647 жыл бұрын
how do you turn the carrier?! I'm getting frustrated trying.
@JoDaddysGarage7 жыл бұрын
Wheels off the ground? Transmission in neutral?
@jrbenally89493 жыл бұрын
What did you use to clean out the old gear oil?
@JoDaddysGarage3 жыл бұрын
Brake parts cleaner.
@adrenalinehigh2070 Жыл бұрын
You have unbelievable long arms!!! How the hell you pull the axel out the right while holding the cam on the left hand???
@JoDaddysGarage Жыл бұрын
With my foot. 😂
@maxlove48217 жыл бұрын
thank you
@automaniacUSA10 жыл бұрын
So how did it work out? I assume less teeth makes it a little noisier than stock.
@JoDaddysGarage10 жыл бұрын
It worked very well. Couldn't hear it at all.
@notyou69504 жыл бұрын
Them powder metal gears are not as good as solid steel, but they are cheaper to make 4 sure.
@gb12098 жыл бұрын
lm from uae thanks for thes vedio deferential
@donaldbannon91495 жыл бұрын
I am getting a suburban soon that has been sitting for 2 years. Same model and year. It too was parked after the spider gears went out. When talking to people with a little mechanical background they say that the new gears can be difficult to put in and the alignment of them is critical. Your video doesn't address this. Is that something someone with average mechanical skills needs to worry about? Your video makes it look relatively easy.
@JoDaddysGarage5 жыл бұрын
It's really not that hard. Unless there's more damaged, it's just pieces out and pieces in.
@scottwilson19055 жыл бұрын
I wanted to see how you got the spider gears back in and you skipped it bummer
@JoDaddysGarage5 жыл бұрын
Sorry. I think it took both hands.
@accuratemarine18 жыл бұрын
good video
@kb3yourmom9128 жыл бұрын
hey Jo I have to do this on my 2000 Silverado same thing I was looking for your follow up bid but haven't seen one... how did the suburban do after the spider gear replacement... need to know I want to do this to mine and save a crap load of money let me know PLEASE
@JoDaddysGarage8 жыл бұрын
+Kelsey yourmom Sorry, I didn't do a follow up. The family is still using it as a daily driver for their 17 year old son. No complaints.
@kb3yourmom9128 жыл бұрын
OK just wanted to know if looks pretty simple was there any grinding after you bottom it back up and after completion it ran fine
@JoDaddysGarage8 жыл бұрын
+Kelsey yourmom In this case, it was all good. Make sure everything is clean before it's closed up.
@bcjdwbiernfjherwfbowfib6 жыл бұрын
When you were driving the suburban with the bad gears, what were symptoms that made you know it was the Spyder gears?
@JoDaddysGarage6 жыл бұрын
It was a friends suburban, and it was making a lot of noise. It also had difficulty moving while it was making the noise.
@bcjdwbiernfjherwfbowfib6 жыл бұрын
Ok. How long did it take you to do everything? Because my Spyder gears are bad in my Silverado, I was considering getting a new rear end but your video made me just wanna put new gears in it.
@bcjdwbiernfjherwfbowfib6 жыл бұрын
Jo Daddy's Garage also, my truck jolts when I put it in park sometimes, and when I hit about 45mph it starts to jolt funny. When I step on the gas a little more it had no problems. I definitely need a new rear end.