This video will walk you through the steps required to remove and replace the rear wheel bearing on your 2003-2007 Honda Accord with rear Disc brakes.
Пікірлер: 60
@yungoldhead5600 Жыл бұрын
I swear to God. The detail that u provide is gold! A lot of people just install and skip steps etc.. U answered every question I had.
@Lfrohawker2 жыл бұрын
This applies to almost any year accord it looks like. I popped off my 91 hub thanks to your video! Thought it was a much bigger pain until I watched this.
@mr.stoneybaloney92142 жыл бұрын
32 mm for the wheel bearing?
@nikokatana3 ай бұрын
Yes, just did it myself yesterday
@Eashlo882 жыл бұрын
Is there any other way to get the race off other than using the cutting tool?
@shaynekraczek3999 Жыл бұрын
I put a thin screwdriver behind it and worked it top, bottom, left, right and eventually got it far enough out I could slide it off.
@Eashlo88 Жыл бұрын
@@shaynekraczek3999 thanks haha I left this comment just over 1 year ago 😂. The race popped right off and luckily wasn’t stuck for ke
@shaynekraczek3999 Жыл бұрын
Haha oh good. Glad you're not still driving around with a busted wheel bearing 😂
@mungox12 жыл бұрын
my local garage wants $500 each to change them, must be the flat rate price
@blue3sierra6723 жыл бұрын
Love the videos, would love to see a diagnose / repair of the F150 door ajar issue.
@urbansoundscapes77343 жыл бұрын
Nice video, a big help to tackle this repair - thanks.
@andreydrozd7696 Жыл бұрын
Привет приятель. Это отличное видео! Все очень доступно объяснил и показал. Также стоит использовать немного медной смазки, по краям центрального колпачка, а также на посадочном месте для колеса на тормозном диске, чтобы колесный диск не прикипал и не пришлось стучать по нему ногой.)) Медная смазка не боится больших температур. Ты крутой механик, удачи тебе!))
@mg87189 ай бұрын
Your breathing in asbesdos dust stop blowing air on that brake area.
@mixedboi Жыл бұрын
This is one of the most detailed videos I've seen. Thanks 😊
@paulbanks94083 ай бұрын
Are the new bearings sealed with grease then ?
@RonGeary3 күн бұрын
What size is the axle nut?
@danair173 ай бұрын
Great video Brother - I've done both rear hub/bearings on my 04 accord while referencing this video. Well done!
@kenrolltideAlabama10 ай бұрын
Got a drill just like that one
@unanimous56789 ай бұрын
Really good video, great detail and thanks for not kicking out from under the car 😅. I just need to see if this applies the same way when the car has drum brakes?
@omarvega1984 Жыл бұрын
Do you have to take off the inner race or why do I need to remove can someone help me doing this today and dident quiet understand that part
@andrewsexton6117 Жыл бұрын
Funny how you just said "if you start with air the. Finish with air...." but then you sprayed brake cleaner
@oregonguy714 ай бұрын
You make great tutorial videos! Thank you! Al in Portland, Oregon
@bmsd619211 ай бұрын
Dope
@kenrolltideAlabama10 ай бұрын
Very well done
@last1king Жыл бұрын
I can't thank you enough for sharing this knowledge. GOD BLESS YOU.
@mplsfarmer3 жыл бұрын
Very thorough. Thank you!!
@charleswilson28722 жыл бұрын
Great job on vido. Only thing I do different is that I bush the caluaber before I take caluaber off.
@chetguida95722 жыл бұрын
We would be friends lol!! Great personality man. Thanks for the awesome video!!
@jozsefizsak3 жыл бұрын
Greatly appreciated! The small details were very helpful to avoid damaging parts.
@saginaw602 жыл бұрын
Cant-cha change just the bearing & use d old hub like i did on d front?
@infinite5403 ай бұрын
Thank you
@papatee3024 Жыл бұрын
Niiiice 🫡
@billydo53763 ай бұрын
Thank you for uploading this video.
@montysonful10 ай бұрын
good job
@rastomasstanford77082 жыл бұрын
I swear this dude was on a dig in Egypt Dust flying everywhere
@Eashlo882 жыл бұрын
The stake on mine is too tight to get any punch into it… what should I do?
@andrewsexton6117 Жыл бұрын
Would a bad wheel bearing cause a tsc light on?
@kyhomegarage34302 жыл бұрын
Thank you bro.😊👍
@bertharris97482 жыл бұрын
Clean it before removing the dust cap. Great vid
@nelsonjaneiro5543 Жыл бұрын
Nice when you have all the tools😅
@danyelgirard27072 жыл бұрын
Merci ça M a beaucoup aidé Doit-on changer les deux roues arriere
@cp1117773 жыл бұрын
Hi good video. Nice and to the point. Quick question : Any grease to use ...? For example the part the new bearing slides onto?
@taylorrobinson90322 жыл бұрын
pretty sure there needs to be friction there. the bearing has a sleeve that sits on the spindle. the sleeve is what he had to crack to get off
@NoCapKana2 жыл бұрын
Why was there no screws? Is that okay to not have screws in it?
@waynebinky Жыл бұрын
The screws do nothing really for us. More for the factory when they are building the car. It lightly secures the rotor while it's travelling down the line.
@farajshamsa34042 жыл бұрын
Very good thank you for this helpful video
@jkkennedy89193 жыл бұрын
Great video champ
@johnathangreay9872 жыл бұрын
Sup homie?!
@hailam78732 жыл бұрын
thanks
@deibupr3 жыл бұрын
Good video, nice! 👍🏻
@PhillipBailey3 жыл бұрын
Good video, well produced 👌
@DIYAutoHomeschool3 жыл бұрын
Thank you, I appreciate it. Glad you liked the video.