2004 dodge ram blower motor troubleshoot

[@alexceballos4398]

Hey guys Thanks for the video. I was able to go through the process of elimination and found the resistor had failed. i had to replace the ignition switch last year because it had fried out. I had to replace the wire harness as well because it got damaged. Your video helped me immensely. Good luck

[@ryanlayton9753]

I wiggled the wire into the ignition and my fan started too seems to be a common theme. Thanks for the good video and help !!

[@jparra4766]

Great video. My ignition switch burnt out similar to yours. I ordered a new one but I also cleaned out the terminals and got the fan to start working again. I'll replace it as soon as I get the new switch. Thanks again.

[@tylermease8465]

Thanks buddy it was my ignition switch too after I went through all the other stuff I appreciate this video it helped a lot!!!

[@willtws9920]

Mine was not the fuse but the power wire had corroded in half under the fuse box. Som advice to anyone that has had this issue. The top two wires going to the ignition switch are for the blower motor circuit. Check for power on the wire that is pink with a black strip first. If you have power there then turn the key to the truck on if the green wire does not have power then it’s an ignition switch/ harness problem. Obviously check this by using a test light and poking it through the wire insulation. I ended up fixing the wire and just installing a 50 amp relay to bypass the ignition switch.

[@daltonmarshall3083]

How exactly did you wire your relay in my wires on mine sre burnt

[@chriskrogh7128]

Same truck same year, great information and Very thorough! Like to buy you one!

[@theAngryMilkman1249]

I have the same issue, thanks for the details video.

[@geraldnugent8413]

Awesome I’m driving freezing I just tilted the steering column and my heat came back on. Thank you. Must be that switch.

[@Jamesd1861]

I’m having the same problems, fan not working thanks for the info 👍

[@truthingrace3594]

Did you notice switch position problems before you motor blower stopped working... Just something I noticed for a while now suddenly I have no blower. The wire connector was bad and I replaced it with the blower and it still didn't work. I wired the motor directly and it works. Next would be the ignition swith and control board.

[@laneburgess1643]

Great video

[@sergio6794]

Thank You for the information ...having the same trouble with blower not working and changed the resistor and blower motor and still not working ...checked the fuses and all are good ...I will order a new ignition switch from RockAuto and hope this fix works

[@clintlittle8833]

Did that fix your problem?

[@sergio6794]

@@clintlittle8833 Yes it had broken piece of copper and shorted out the ignition switch and now it's working perfectly

[@noname9464]

I have an issue with the blower not working. Not getting power. I hooked power to the green wire on the blower and it works all speeds. But no air comes out of any vent no matter what setting I put it on. Hot or cold or nothing no air at all. Could it be the switch or are all my blend doors broken?

[@freeamerican2382]

So the blower motor seems to work well but on long trips (say 100 miles) the air slows down n barly blows out air. The blower motor looks clean n even new. Could it be that the motor is over heating because if I let it sit an hour it works well again . Any suggestions?

[@KevinKey-dd3oh]

I replaced my resistor like everyone else, but my fan still only works on high. Any other suggestions ?

[@djscottymaxx]

Replaced ignition switch, resistor, still nothing. Didnt check the blower motor itself yet or the switch cluster. Mopar is known for this the resistor went bad in both my dodge vans too

[@elliottleath2139]

My wires and ignition switch on my 03 burnt up yrs ago and I thought they did it again but it’s something else. Last time I developed a theory that the lower fan speeds using a higher resistance make the wires overheat and for whatever reason that seems to be at the ignition switch. Anyone who knows more about electricity can correct me but I decided then to only use the high speed and now several yrs later the wires and ignition switch aren’t burnt idk what it is this time🙃

[@donovanlucibello379]

Do you have a part number or possibly a noun to ask for it at the parts store? Great video, thanks!

[@charleswhite5153]

Mine works without the key being in it. Any ideas what it could be?

[@Zeek808]

Probably ignition switch contacts welded closed.

[@jesusgallardo7884]

Awesome 😢