2006-2012 Mercedes Benz Transmission Control Module Unlocking and Adaptation Still No Reverse No ...

[@خالدالعجيلي-ي9خ]

Did we shoud rest TCM after changing electronic module gearbox

[@ДимитърПопов-ц2ю]

Hi , I have the same problem, how did you fix it, thanks

[@GustavoRodriguez-mu6td]

I have the same problem same car gl450 2010. Please help. What was the problem??

[@Amg641]

I have a no crank start problem the fault code: P1925 Drive authorisation has been refused by control module N15/5 esm Any advice?

[@BestCarFixes]

see if you can communicate with esm module

[@Amg641]

@@BestCarFixes I tested can hi and can lo on can bus c the voltage was perfect but on can b when asleep it wouldn't give me a reading? awake can hi was 0.72v and can lo was 4.4v

[@giorgiispirov7129]

Hello, Is it possible with the help of AUTEL 608 PRO to Erase and Learning the Gearbox on Mercedes W212, 2015 , 722.996 VIN : WDD2120061B148466 ? Thank you.

[@BestCarFixes]

yes if you have the old one

[@giorgiispirov7129]

@@BestCarFixes How do you know if it's old or new?

[@cilkitzvictoria4586]

Salam,yes sir,I have c200k 2009model, I change supercharger and boots sensor mass sensor,still no boots coming

[@tyroneking5889]

Thank you for your videos. What was the solution for this issue?

[@BestCarFixes]

they replaced the transmission with used one now it has to be programmed

[@hexarid3969]

@@BestCarFixes is it just electric kit or the whole transmission anyway?

[@uyinmwenaiseosa3704]

I think it's the whole gearbox

[@iraqiservices7100]

رَبّـ❤ـيٌ يزيدك ويرزقك لان عربي محد يدعمه .

[@KJsv3woSuWuBk2U]

My car move but won't shift gears Automatic shift gear just had Major tune up and top off with check engine light on had diagnostic said shift gear sensor issue

[@omars3506]

Any update on this mate ?

[@train4905]

Exellent😊

[@nathanfrench2971]

Hey wea are you located i need your help

[@xplosioncomedy6127]

I think this fault is from the Inteligente servo module (ISM) and also there is a relay in charge of the ism if it loses steady current it can cause this .

[@BestCarFixes]

Thanks Alot i will chek and let you know

[@xplosioncomedy6127]

@@BestCarFixes okay sir

[@jiveone6503]

Hi can you tell me where the relay would be locators at?

[@robertrobbins837]

P1925 I think this trouble code is stopping my car from starting casterly cranks but no spark and I'm getting gas

[@princeoffame100]

can you clone a isu ?

[@uyinmwenaiseosa3704]

Sir try manual shift the gear from neutral to reverse

[@nathanfrench2971]

How can i contact you sir ?

[@خالدالعجيلي-ي9خ]

Thank you so much my Muslim friend

[@agrautomotivellc3283]

the module was not programmed correctly. you have to do an initial startup on a virginized unit or it will not drive and the module is useless. Also if it was a used unit you have to use a new virginized unit. then you can program it.

[@BestCarFixes]

Ok

[@BestCarFixes]

I did some of the used tcm from the same car and it work fine

[@partoems9376]

Hi, I changed the TCU unit and there is this error code - The start enable signal was not issued by the control module drive authorization system. When I checked there is VIN mismatch on TCU/ECU. Car is 2016 c300 4m equipped with VGS4 tcu version. Can IM608 or MS919 help me write the correct VIN on the tcu? Thanks

[@danielestrada12]

What a waste of time doing the reset over and over again , need to be fixed first of all

[@robertrobbins837]

P1925 Drive authorized refused by the control module

[@romeoadryan]

check ignition swich (gateway)

[@bishan32]

Hi can you please suggest how to fix error code p0606 component y3/8n4 fully integrated transmission control unit is faulty. Can i service or have to replace the sparepart ?

[@BestCarFixes]

most of the time code p0606 is software related see if an upgrade can fix it or get next one

[@bishan32]

@@BestCarFixes hi thanks for your advice

[@engineguruji4254]

Hi I'm from India can I get your whatsaap number.

[@alizreikautopower4649]

You need put the scn number and the ehs number

[@youseftaha8141]

السلام عليكم هل حليت هاي المشكله واذا تنزل فيدو الحل

[@alijajieh6954]

Mouhamad it need programing

[@andymacka5553]

fix my car please merc c class need you expertise mate

[@alijajieh6954]

And scn coding correct

[@MuhammadIsmail-qz9xp]

I am Mechanic in the Dubai you need 15 years experience

[@التطورفكره]

Boss can i have your number to ask a question?

[@KJsv3woSuWuBk2U]

I held the gas down 15 seconds on start no idle position or position start 1

[@BestCarFixes]

Diagnose and see what. Codes are you getting

[@KJsv3woSuWuBk2U]

@@BestCarFixes Fault code 2768 component Y3/8N2(internal speed sensor VGS) is defective and Fault code 2*** signal for Y3/8N2 not sure I think it was a repeat code paper faded on physical report. Report date 8/30/22 model E350 Mercedes Benz yr 2007

[@KJsv3woSuWuBk2U]

At this time 8/30/22 vehicle battery replacement

[@KJsv3woSuWuBk2U]

Diagnostic cost 500 dollars how can I do this what devices do I need for phone devices

[@kofiobour7039]

HI

[@fsffsf6747]

استاذي ممكن رقم جوالك اتواصل معك

[@kofiobour7039]

PLS NUMBER