2007-2014 Cadillac Escalade EXT Custom Platinum Dash Swap, Suede, Wood, Heated & Cooled Cup Holders

07-14 Cadillac Escalade EXT Platinum Dash Door Panel Swap, Suede, Wood, Heated & Cooled Cup Holders. Covers 2007 2008 2009 2010 2011 2012 2013 & 2014. The Escalade EXT was only available in Luxury and Premium. I wanted to do a Platinum interior swap so I changed the door panels, dash and trim.
►Support the Channel & Purchase WorkingWithWimberley Apparel!◄
teespring.com/...
As an Amazon Associate I earn from qualifying purchases
Craftsman Socket Set: amzn.to/37fwBZW
GoPro Hero 7 Black (What I Use to Record): amzn.to/2NCDCwf
► Subscribe: www.youtube.co...
► Website: www.workingwith...
► Instagram: / workingwithwimberley
► Facebook: / workingwithwimberley
► Twitter: / wkwithwimberley
► KZbin: / workingwithwimberley
This is a how-to video for the “Do-It-Yourselfer” working in the home, driveway or garage. No fancy or crazy expensive tools. I'll show you step by step how to get the job done!
*If the video was helpful, remember to give it a "thumbs up" and consider subscribing*
Music by @tru_inferno: truinferno.ban...
Disclaimer:
Due to factors beyond the control of Steven Wimberley & WorkingWithWimberley, I cannot guarantee against improper use or unauthorized modifications of this information. Steven Wimberley & WorkingWithWimberley assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Steven Wimberley & WorkingWithWimberley recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Steven Wimberley & WorkingWithWimberley, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Steven Wimberley & WorkingWithWimberley.
2007-2014 Cadillac Escalade EXT Custom Platinum Dash Swap, Suede, Wood, Heated & Cooled Cup Holders #WorkingWithWimberley Episode 129

[@greatgandalf5233]

My 2008 lower dash Escalade 6.2 EXT has developed cracks on both sides of the Dash..Thanks for sharing the knowledge!

[@WorkingWithWimberley]

No problem!

[@DJKadilac]

Looks good bro! The mistake I made was not allowing the adhesive to FULLY dry before trying to fit the material. I’m going to redo it in suede.

[@WorkingWithWimberley]

Thanks! Good luck!

[@xxcloudxx6606]

Love the coco/white linen.

[@WorkingWithWimberley]

Thanks!

[@omarzowila]

This makes the truck look like it was a Platinum from factory and Cadillac should’ve made a Platinum version of the EXT

[@WorkingWithWimberley]

Yeah, that would’ve been cool.

[@daroachdoggjr188]

This looks really fresh, nicely done

[@WorkingWithWimberley]

Thanks! Much appreciated!

[@a.r.bigdog8957]

New subscriber. Decided to keep my 07 EXT (had it since 09). Really glad I did after watching your channel 😀 Thanks brother. May GOD continue to bless you and us all 🙏

[@WorkingWithWimberley]

You’re welcome! I’m glad the video helped! And God bless you too!

[@dominicsaad4103]

That car is a gem don’t ever sell it

[@djlonsiamdjlons9179]

Looks good bro

[@WorkingWithWimberley]

Thanks!

[@mrtennessee1o1]

Simply just too clean! Bravo! This walk through video was on point. I've used several of your EXT videos to work on my own.

[@WorkingWithWimberley]

Thank you! I definitely appreciate that! Glad it helped.

[@israela9631]

Great work big bro 👊😎

[@WorkingWithWimberley]

Thanks! I’m glad it worked out. 👌🏽

[@alhamedi66]

Amazing beautiful project clean work. I plan to upgrade my 2007 ext to platinum but no used parts around me must order all from USA overseas shipping too much expensive. Can you put list by all parts diffrant between laxury and platinum. How much total cost Well done.

[@WorkingWithWimberley]

Thank you! I don’t have a list. I just bought parts as I could find them. I know it’s door panels, door sills, glove box, knee bolster, wood trim and b pillars. You should be able to find the part numbers on GMpartsdirect.com

[@alhamedi66]

@@WorkingWithWimberley Thank you for your quick reply and interest and patience. Best regards,

[@WorkingWithWimberley]

@@alhamedi66 You’re welcome. No problem!

[@TRUCKOCD]

Was going to put the Platinum door panels in my Denali truck but decided not to bc the tan is lighter shade on them.

[@WorkingWithWimberley]

I talk about that at 6:12. I had to get more pieces to match. Thankfully I was able to find them.

[@ritawimberley544]

It looks very luxurious 🥰

[@WorkingWithWimberley]

Thanks mom!!!

[@shatteredaspirations746]

I wonder if those door panels would fit a 2013 Yukon XL.

[@WorkingWithWimberley]

They should fit. You just need to check the window switch trim. They changed them at some point on the front doors.

[@dadrut305]

Nice work. I have a 09 platinum esv thinking of doing the A-pilers in a darker material like the coco brown seats. Where did you get your material ?

[@WorkingWithWimberley]

I purchased it from joann fabrics. It’s Stretch Faux Suede.

[@sergiochavis223]

Hey, I love the video. I have a 2009 base Escalade. I want to make my interior all black with the platinum seats. But where did you get the center console with the logo? I like that.

[@WorkingWithWimberley]

Thanks! I bought the console lid from Amazon and had it embroidered locally. Check out this video where I go over the process. kzbin.info/www/bejne/q3jIoGCohdife5o

[@AlanTrades]

Wow where did you learn how to do all this

[@WorkingWithWimberley]

My father taught me. He’s the reason I started the KZbin channel to share with others! 👍🏽👌🏽

[@Cleaning_Hero]

Wow! It looks awesome! Can you replace the steering wheel airbag cover with a leather-wrapped version?

[@WorkingWithWimberley]

I don’t think Cadillac made a leather wrapped version of this particular air bag.

[@chuk0one47]

I have the same Escalade 2014 esv but mines have premium package I got the cold heating cup holders that I want to install can you explain on how did you wire the cables to the cigarette lighter power

[@WorkingWithWimberley]

If your Escalade didn’t come with heated and cooled cup holders from the factory, the connector won’t be there. You have to wire it up yourself. To wire it up, I tapped the red power and black ground wires into the cigarette lighter. All the rest I combined and tapped into a fuse that only gets power when the key is in the run position. That was it.

[@giohuncho]

I have a 2007 Escalade and I was wondering if I could put platinum parts on it like the cluster since mine is different and stuff like the trims, door panels, radio and center console

[@WorkingWithWimberley]

I know you can do the trims, door panels and console. I’m not sure about the electronics like the cluster and radio. You’d have to do some research on those.

[@edwardgarcia9170]

Is it possible to go over how to fix sunroof when it won’t close

[@WorkingWithWimberley]

Unfortunately I don’t have the 2012 Escalade EXT anymore. I now drive a 2015 ESV.

[@samariaclark3222]

If you still have the EXT, would you consider selling it? Very nice truck!!

[@WorkingWithWimberley]

Thanks! The EXT is gone. I’m in a newer ESV now. kzbin.info/www/bejne/r6fFlpqabdxge6c

[@ezradegreat]

Great video! I just bought a 2007 escalade Esv. I got the cathedral tail lights for it. But I saw you had the heated and cooled cup holders. Where did you go to get that piece? Would really appreciate if you share that info. I looked everywhere and was not successful. Thx!

[@WorkingWithWimberley]

Thank you! I bought the cup holder from a junkyard that I found on car-part.com and they shipped it to me. Basically, you’d have to find one at a junkyard or eBay.

[@ezradegreat]

@@WorkingWithWimberley ok gotcha. Thx! I been searching every junk yard and no luck yet. Do they wore right in? Or did you have to do some extra work to make them functional?

[@WorkingWithWimberley]

@@ezradegreat If your Escalade didn’t come with heated and cooled cup holders from the factory, the connector won’t be there. You have to wire it up yourself. To wire it up, I tapped the red power and black ground wires into the cigarette lighter. All the rest I combined and tapped into a fuse that only gets power when the key is in the run position. That was it.

[@Papadoodles]

Can you make a video on replacing the center consul with the heated and cool cupholders.

[@WorkingWithWimberley]

Unfortunately I can’t. The Escalade EXT is gone. But the wiring is simple. Tap the power and ground from the cigarette lighter. And the rest of the wires can all just go to a ignition only power source.

[@manbehindthecamera9898]

Look good I’m doing something similar to mine

[@WorkingWithWimberley]

Thanks! It was a lot of work but I was really happy with the result.

[@dirtykustomz]

Sick

[@WorkingWithWimberley]

Thank you! Much appreciated!

[@chaelodoul9401]

Dayum great work!!!!! Wish I could hire you to do mine.

[@WorkingWithWimberley]

Thanks! Much appreciated. It was definitely a labor of love.

[@vehcor]

Looks good!

[@WorkingWithWimberley]

Thank you! The dealership that I traded it in to tacked on a lot more than I got for the trade in and it sold in less than a week. I guess I should be flattered.

[@daroachdoggjr188]

This is brilliant, love your ambition and efforts

[@AlanTrades]

How did you wire up the heated/cooled cupholders? Do they actually keep the drinks hot or cold?

[@WorkingWithWimberley]

It did keep cans cold. I actually never used it for anything hot. If your Escalade didn’t come with heated and cooled cup holders from the factory, the connector won’t be there. You have to wire it up yourself. To wire it up, I tapped the red power and black ground wires into the cigarette lighter. All the rest I combined and tapped into a fuse that only gets power when the key is in the run position. That was it.

[@AlanTrades]

@@WorkingWithWimberley cool thanks! Do you remember which fuse you tap into? And what I'd the fuse tap you need. It's the fuse box on the driver side panel right? The one to the left of the steering wheel?

[@WorkingWithWimberley]

@@AlanTrades I don’t remember. But in this video, I tapped under the hood for a LED running light. kzbin.info/www/bejne/b2eYc2Rtf8mIf6c

[@AlanTrades]

@@WorkingWithWimberley if you could check your driver fuse panel and snap a photo or video that would be great. I need to tap a heated steering wheel as well.

[@WorkingWithWimberley]

@@AlanTrades Unfortunately I cannot. I traded in the 2012 EXT a year ago for a 2015 ESV which I currently have.

[@wezzil]

Weird question but would you know how to hook up the platinum seat DVD players?

[@WorkingWithWimberley]

I don’t. If it’s separate from the rest of the entertainment system, you’d just need power. If it connects with the head unit, I don’t know how you’d do that.

[@yunjang7548]

Wow! You are the Man! I have the Harley edition Ext. Would love to finish Harley ing it out. This is giving me some great ideas. Idk what they're called, but I want to Harley those 2 spines that come down the sides along the windshield interior where the speakers are. What would you suggest?

[@WorkingWithWimberley]

Thanks! 😂 I would probably say go with orange suede. That would pop with the Harley theme.

[@yunjang7548]

@@WorkingWithWimberley Thanks. On a mission for Harley orange now.

[@sergiochavis223]

Where did you order the platinum door panels? I can’t find a good set no where.

[@WorkingWithWimberley]

I found mine at car-part.com but I also saw quite a few on eBay.

[@jasonibis]

hey where did you get the power for the heated cup holder, i dont see an extra jack in my truck

[@WorkingWithWimberley]

If your Escalade didn’t come with heated and cooled cup holders from the factory, the connector won’t be there. You have to wire it up yourself. To wire it up, I tapped the red power and black ground wires into the cigarette lighter. All the rest I combined and tapped into a fuse that only gets power when the key is in the run position. That was it.

[@Bluu1017]

Great video!👍 I have a 2013 Escalade premium and I was wondering. Where do you order all your stuff for the Escalade?

[@WorkingWithWimberley]

I purchased to platinum dash from eBay. The door panels came from a junkyard I found on car-part.com and they shipped them to me. All the rest of the stuff like the knee bolster, glove box and door sills came from a local junkyard. It was the only time I’ve ever seen an Escalade platinum in a junkyard. It was my lucky day.

[@keepitthoro6768]

Nice work! Way better, now just match the headliner with the rest of the brown

[@WorkingWithWimberley]

Thanks! I don’t have this Escalade anymore. I drive a 2015 Escalade ESV now.

[@akramalzain9730]

Looking fire 🔥🔥🔥

[@WorkingWithWimberley]

Thank you! It was definitely worth it!

[@DavidJones-pv5wn]

How u get to fit the cup holder did you cut the air vent it don’t fit it’s to deep

[@WorkingWithWimberley]

I believe I heated the vent with a heat gun so that I could soften it. Then I pressed it in a bit to get the extra room for the cup holder. I didn’t cut it.

[@ChevySS1968]

Hey man, nice vid! I've got a 2010 EXT that could use a little something. Can I ask how you got the knee-contacting console trim piece off? Are they just held in by clips?? My right knee firmly hits that trim piece (the piece you covered with brown suede), and I am gonna have an upholstery shop modify it for clearance. Thanks! Dave F.

[@WorkingWithWimberley]

On the bottom closer to the pedals there are a few bolts. On the top closer to the steering wheel, it’s clips. That’s it.

[@ChevySS1968]

@@WorkingWithWimberley - thanks very much!!!

[@WorkingWithWimberley]

@@ChevySS1968 No problem!

[@frankventimiglia5098]

i have same truck to a tee 2007 i just did mine with raptor radio

[@WorkingWithWimberley]

That’s awesome! The EXT is a great truck.

[@HaulingStuff]

I’m gonna bring you my truck… beautiful job..

[@WorkingWithWimberley]

Thank you! It was a lot of work, but not too bad. I think the toughest part would be tracking down all the platinum parts.

[@cliffhall4198]

I have the same truck (just fitted with a 2019 front clip) and i was hoping you could tell me where you got the platinum center dash surround from??? i've been looking for about 3 weeks now with no luck.

[@WorkingWithWimberley]

I got it all from eBay. It’s really the only way. You’ll have to check pretty much daily to see if someone lists the parts.

[@hillarykingart1983]

What is the tool you are using to pry trim pieces off? Thank you

[@WorkingWithWimberley]

Nylon Pry Bar Kit: amzn.to/38iJRgu

[@mikeh1348]

Where did you get the heated and cool cup holders

[@WorkingWithWimberley]

I found them at a junkyard. I used car-part.com to find them. Your best bet is probably eBay though.

[@SIXONETHATSALL]

Where did you purchsse the heated and cooled cupholders

[@WorkingWithWimberley]

I found them used on eBay.

[@vincenzoaprea3821]

How did you hook up the heat/cool cup holder

[@WorkingWithWimberley]

@@vincenzoaprea3821 If your Escalade didn’t come with heated and cooled cup holders from the factory, the connector won’t be there. You have to wire it up yourself. To wire it up, I tapped the red power and black ground wires into the cigarette lighter. All the rest I combined and tapped into a fuse that only gets power when the key is in the run position. That was it.

[@dianecb1997]

My car it’s a 2007 but has all the interior from a 2014 platinum edition but I have solo problems 🥺😭 the cup holder are not heating or cooling I disarm it and I didn’t find a plug for connect the heating and cooling. Pleaseeeeee do you know some one for do this cup holder work 🙏🏻🙏🏻🙏🏻 pleaseee

[@WorkingWithWimberley]

If your Escalade didn’t come with heated and cooled cup holders from the factory, the connector won’t be there. You have to wire it up yourself. To wire it up, I tapped the red power and black ground wires into the cigarette lighter. All the rest I combined and tapped into a fuse that only gets power when the key is in the run position. That was it.

[@dianecb1997]

@@WorkingWithWimberley thanks so much I love your videos please do more like this one 🙏🏻😁 I’m an Escalade lover thanks for shearing

[@dianecb1997]

@@WorkingWithWimberley im sorry last question where can I buy the connectors that I need for this 🙏🏻. Thanks again for you help

[@WorkingWithWimberley]

@@dianecb1997 There is no connector you can buy. Your Escalade was not equipped to plug in the cup holder wires. You have to cut, splice and connect the wires yourself. This is custom work that requires you to have a decent understanding of wiring.

[@dsten5947]

Great vid! Can you show how to do that to a trailblazer in your next one?

[@WorkingWithWimberley]

😂 It’s the same process as what I did on the Escalade. If you’re feeling brave, we can definitely throw some suede in the TrailBlazer!

[@tyrannyterminator4179]

How did you wire in the heated and cooled cup holders?

[@WorkingWithWimberley]

If your Escalade didn’t come with heated and cooled cup holders from the factory, the connector won’t be there. You have to wire it up yourself. To wire it up, I tapped the red power and black ground wires into the cigarette lighter. All the rest I combined and tapped into a fuse that only gets power when the key is in the run position. That was it.

[@tyrannyterminator4179]

@@WorkingWithWimberley perfect! Thank you!!

[@WorkingWithWimberley]

@@tyrannyterminator4179 You’re welcome!

[@glezrob]

Great job and looks great Thanks for the info how getting wired

[@Pitbull14218]

Really good job bro! Great video!

[@WorkingWithWimberley]

@@Pitbull14218 Thanks! I appreciate that!

[@ronisharobinson1735]

Looking good! Do you think the 2015 escalade steering wheel would fit? Im thinking about doing it and did you just change the trim and door panels?

[@WorkingWithWimberley]

Thanks! I’m not sure about that steering wheel since it has different buttons and controls. I changed the door panels, door sills and some of the interior plastic trim. I disassembled parts of the dash and wrapped it with suede.

[@DJ_BIGWOO]

? How did u wire up the cup holder is the plug already ran as a option??? Looks great bro

[@WorkingWithWimberley]

Thank you! If your Escalade didn’t come with heated and cooled cup holders from the factory, the connector won’t be there. You have to wire it up yourself. To wire it up, I tapped the red power and black ground wires into the cigarette lighter. All the rest I combined and tapped into a fuse that only gets power when the key is in the run position. That was it.

[@DJ_BIGWOO]

Thanks Bro

[@WorkingWithWimberley]

@@DJ_BIGWOO No problem!

[@E_-lb6df]

Good video and nice Escalade

[@WorkingWithWimberley]

Thanks! Much appreciated!

[@MegaHowtoMan]

What adhesive did you use on the swede?

[@WorkingWithWimberley]

I used 3M Super 77. amzn.to/3H45eWk

[@DavidJones-pv5wn]

Want to do this to my 2012 ext you have any links were to get parts or get started look so much better

[@WorkingWithWimberley]

I don’t have any links. Your best bet for the interior pieces is going to be eBay and if you’re lucky, a local junkyard. The suede was purchased from Joanne fabric.

[@funguy7979]

I heard the avalanche and caddy ext dash has the same install points. Are they direct swaps?

[@WorkingWithWimberley]

I don’t know, but I’ve seen a few guys swap Escalade dashes into Silverados. I’d ask one of them. kzbin.info/www/bejne/h3q8eISYjd6sr5o

[@funguy7979]

@@WorkingWithWimberley thanks

[@WorkingWithWimberley]

@@funguy7979 You’re welcome.

[@jdm2877]

WOW

[@WorkingWithWimberley]

Thanks!!!

[@eli2976]

I see ya boi.. Niceee👌

[@WorkingWithWimberley]

Thank you!!! 👌🏽👍🏽

[@thegoodlifedrive]

My dash broke in the same spot

[@WorkingWithWimberley]

I decided to repair mine and cover it. It turned out pretty well. kzbin.info/www/bejne/ooObqnlog86HkK8

[@LiLrampage209]

Do you have a video showing how you wrapped the A-Pillars?

[@WorkingWithWimberley]

I show the process @ 3:45 and it’s the same for the A-Pillars. The only difference is I had to pull the existing fabric off the A-Pillars before I glued on the suede.

[@LiLrampage209]

K thank you that’s what I was wondering because the fabric on mine is loose and ugly whoever had it before me tried to regule and the glue is showing thru 🤦‍♂️ but I really like how your looks with the suede 👍 thank you

[@WorkingWithWimberley]

@@LiLrampage209 No problem!

[@9876-e1p]

Where can I buy the same kit?

[@WorkingWithWimberley]

You have to try and find the pieces used. eBay is probably your best bet.

[@jamesanderson4014]

Good job great video. Not a GM owner but highly appreciate your work. Going from a Concorde to install interior options from 2002 300m special which I stripped engine fuse block to tail light wiring. Need dash and upgraded BCM speakers and door panels installed. Programming will be the issue fitment flawless. You got a nice ride very well done.

[@WorkingWithWimberley]

Thank you so much! I hope your project goes well!

[@davidrossi8480]

My 2008 Escalade windshield vent piece is cracked in the EXACT same place as yours. Wonder why that is. Any ideas?

[@WorkingWithWimberley]

It’s a known issue. It’s cheap plastic and becomes brittle being in the sun.

[@investinghutler5323]

Awesome!!👏🏼👍👍✊🏼💪🏼💪🏼

[@WorkingWithWimberley]

Thanks! Much appreciated!

[@realacerboy30]

Second ✊🏿

[@WorkingWithWimberley]

Thanks bro! ✌🏽

[@bjohns6279]

Nice job. Very cool. I wish the EXT came as a platinum. Would make things a lot easier….

[@WorkingWithWimberley]

Thank you! Same here. Maybe we’ll see another EXT in the future.

[@chrismadison8786]

Good morning, Sir, How much did this complete job cost you???

[@WorkingWithWimberley]

The highest cost was the door panels. I think I paid like $600 total for all four. And the platinum dash and cup holders I paid like $300 total for that. The rest of the plastic interior panels I found cheaply at a local junkyard and all the suede was really inexpensive, it just took the effort to wrap the parts. And I did offset the cost by selling all the original parts that I replaced. That brought the cost down quite a bit. So if I had to guess, it probably cost me $300 to $400 total after selling all the old parts. It took a lot of effort though.

[@liljune8209]

How much did this run you

[@WorkingWithWimberley]

Probably around $900 total, but I sold the old parts on eBay and Facebook marketplace to offset the cost so it was actually less than that.

[@shawnbraden6689]

Good work dude

[@WorkingWithWimberley]

Thank you! Much appreciated!

[@omarnino449]

Where did you buy the suede material from?

[@WorkingWithWimberley]

I got it from Joann Fabrics. You can find something similar on Amazon, just make sure it has a little stretch. It should contain spandex. Something like this: amzn.to/3D2IRiz

[@omarnino449]

Ok thanks for your help

[@WorkingWithWimberley]

@@omarnino449 No problem!

[@D.Magic_]

Very nice 👍🏿

[@WorkingWithWimberley]

Thanks!

[@mrdeanv4414]

Wow...looks amazing! What year corvette are you sitting in?

[@WorkingWithWimberley]

2002 Corvette Z06, 1995 Cadillac Fleetwood Brougham and 2015 Escalade ESV.

[@ROMPE_NALGAS_24-7]

Great videos

[@WorkingWithWimberley]

Thanks!

[@ElFinoJefe]

Looks Supperr

[@WorkingWithWimberley]

Thank you!

[@michaelschneider5190]

Wow, came out great!!

[@WorkingWithWimberley]

Thank you!!

[@sonofogun8351]

Great job

[@WorkingWithWimberley]

Thank you!

[@royhickman4679]

🔥🔥🔥🔥🔥🔥👍🏾👍🏾

[@WorkingWithWimberley]

Thanks!!

[@shotimemsu]

fire

[@WorkingWithWimberley]

Much appreciated bro!! 🔥🔥🔥

[@indevibe]

Thank you very much for this tutorial.. The A pillars and forward Vents looks amazing.... We're they hard to get done... I like the way it look

[@WorkingWithWimberley]

The A-Pillars were easy, but the part under the windshield was a little tough because you have to cut around the vent.

[@indevibe]

@@WorkingWithWimberley oh ok, I see... Most of our trucks have VENT CRACKING ISSUES. I think this would mitigate that instead of cover all dash cover.... But the Interior looks clean.. I am going to take a stab at it......

[@chuysprojectssilverado1642]

Great video looking forward to swapping my interior to a platinum

[@WorkingWithWimberley]

Cool! The dash trim is the easy part. If you do the door panels, you’ll have to hunt for those Linen interior pieces.

[@Jacblack69]

I see you pimpin over there....is that a factory radio in there,and how did you put the cool and heated cup holders in?

[@WorkingWithWimberley]

Yes, it’s the factory radio. The cup holder is wired to get its power from the cigarette lighter. The cup holders aren’t bolted in. They just pop in and out with clips like the dash pieces.

[@VITODABOSS1]

@@WorkingWithWimberley I have a wire connection on the side of my cup holder. However, I can not find the connector to plug into it. Where is it?

[@WorkingWithWimberley]

@@VITODABOSS1 If your Escalade didn’t come with heated and cooled cup holders from the factory, the connector won’t be there. You have to wire it up yourself. If I remember it correctly I tapped the red power and black ground wires into the cigarette lighter. All the rest I combined and tapped into a fuse that only gets power when the key is in the run position.

[@dianecb1997]

@@VITODABOSS1 I have the same exact problem 🤦🏼‍♀️

[@bugsbunnygang7188]

Send def go for the brown seats too, they nice

[@WorkingWithWimberley]

Yes, the brown seats are nice! Very hard to come by though. And they never made the brown seats for the EXT.

[@raolito1980]

Easy swap since you already have an escalade

[@WorkingWithWimberley]

Ok thanks.

[@chuk0one47]

Nice ? You don’t have a video on how you made the cup holder work

[@WorkingWithWimberley]

Thanks. No I don’t have a video on that. It was trial and error. I eventually just tapped into the power of the lighter.

[@teddybarboza6697]

Looks amazing When you tap into the power the way you did does it allow for the buttons for the hot and cold to light up as well?

[@Daniel4real20]

Where did you get the door panels?

[@WorkingWithWimberley]

I found a salvage yard on car-part.com that had a set. There’s also a decent amount of them on eBay.

[@raolito1980]

Dang now you got me wanting to do Escalade interior in my gmc Sierra. Man hold up!

[@WorkingWithWimberley]

If you can find the parts, do it!!!!

[@raolito1980]

@@WorkingWithWimberley offer up has a dash but I would need panels for doors

[@WorkingWithWimberley]

@@raolito1980 I would check eBay. There seems to be a lot of door panels on there. Of course it’s going to be up to you as far as how much you’re willing to spend.

[@Bestbro2012]

Hello, what did you use/how to wire up the cup holders?

[@WorkingWithWimberley]

I tapped into the power and ground on the cigarette lighter for the power wires. And all the rest, I combined and tapped into an accessory fuse in the fuse box so that it knows to only turn on when the key is in the on position. That was it.

[@Bestbro2012]

@@WorkingWithWimberley thanks!

[@WorkingWithWimberley]

@@Bestbro2012 You’re welcome!

[@8151noname]

Hello Wimberley, Your truck looks great. Was the heated and cooled cup holder plug and play?

[@WorkingWithWimberley]

No it wasn’t. But it was pretty easy to do. I tapped into the power and ground on the cigarette lighter for the power wires. And all the rest, I combined and tapped into an accessory fuse in the fuse box so that it knows to only turn on when the key is in the on position. That was it.

[@8151noname]

@@WorkingWithWimberley Thanks, I think I'm going to have a heck of a time finding one of those.

[@8151noname]

According to the dealer I can still get the cup holder from them.

[@WorkingWithWimberley]

@@8151noname That’s good. How much? I usually see them go for $500 on eBay.

[@8151noname]

@@WorkingWithWimberley Hi, They said $470.00 before tax. That's Canadian, I'll verify that when I go to the parts counter.

[@Papadoodles]

Great videos very informative

[@WorkingWithWimberley]

Thank you!

[@khalillong698]

Solid work brother

[@WorkingWithWimberley]

Thank you!

[@ikateulilo9058]

No mods? Looks good!!!

[@WorkingWithWimberley]

Besides the interior, the only other thing I did was a Gibson dual exhaust. 👍🏽

[@mndnmne]

Looks really good!!!

[@WorkingWithWimberley]

Thanks!!!

[@RonGau]

looks awesome 👏🍁🙋‍♂️

[@WorkingWithWimberley]

Thanks! Much appreciated!

[@jayquezada3412]

Came out sick bro

[@WorkingWithWimberley]

Thanks! It was tricky getting the suede on the dash, but it was worth it. 👌🏽

[@dylanb2142]

excellent job!

[@WorkingWithWimberley]

Thanks!!!

[@TruInferno]

Ayeeeeeee another project

[@WorkingWithWimberley]

Yes indeed! Keeping the Escalade fresh.

[@TruInferno]

@@WorkingWithWimberley this one makes me want to get a really cool whip so I can work on the interior like this

[@WorkingWithWimberley]

@@TruInferno You can customize the Malibu. I just saw a guy with 22” wheels on a Malibu just like yours.