2008 Mercedes Benz C350 Front Sam Module Defective Caused No Communication With Engine Computer Info

[@W204CommunityNG]

The fan kicking in at highest speed due to no information. Spot on.

[@toxicplay3450]

Yes sr.!! 🙏

[@roythomasful]

eXCELLENT! My school's motto was: knowledge is power. Scientia est potentia! bless you!

[@IrivbojeDickson]

Thank you so much sir, for your contribution in automotive technology thus far

[@nuntegraham9550]

Thank you so much for your video!! It helped a lot. I'm changing my front SAM module, but I can't seem to get those two full power wires out. The ones on each side of the SAM.

[@mohamedtharwat2054]

شرحك مبسط وفوق الممتاز انت رائع

[@pezzoman11]

Hi there You are my best guide to solve my similar situation. I just order a new one . But when I put it, the car won’t start unless is coded?

[@IssaMukuru]

Teach how modifield turn signal of mercedes benz for generation😢 imposible or not?

[@nuntegraham9550]

So I was having trouble with my 09 Mercedes Benz c350...no turn signals, or wipers, nor high beam. And my fan ran on high just as you said. I changed the SAM module with one that has the exact same part number. Now I have no cruise control and still no turn signals or wipers or high beam and my fan still runs on high!!! Could it be something else?

[@adrielbatista6439]

What if the part numbers is different by only one number is okay to use?

[@musiconly9742]

Hey I just got used Sam module with same part number and diagram number do I need to get tech to program the used Sam or it safe to plug and play , only asking because I don’t wanna lose functions I have in my car thank you

[@brandendegroat2976]

Thank you very much! Very informative and just the answers I needed! Liked,subscribed sir

[@BestCarFixes]

Thanks

[@dannysautotech7171]

​@@BestCarFixes hello sir, am having issues on how to program tail gate module on Mercedes glk 350

[@Lamuel-ht6lh]

Hi. I have a problem with my own . 012 C 300 Mercedes 4 matic: my viper's my signal & the horn does not wrk

[@lyesbenslimane990]

salam and thank you for your help

[@jimkillen1065]

Appreciate the videos

[@whlawson5812]

Good morning to you. 80% of SAM issues are due to corrosion caused by condensation moisture & dust?. If yes, how about taking out SAM still in good working condition, to be cleaned, dried out gently & then spare with a thin layer of CRC urethane spray just onto the PCB board. This would be like a PM. Too thick a layer of urethane spray might trap more heat in the PCB board?. For each cleaned up terminal connection will a drop of WD40 or thin application of dielectric grease be advisable?. Regards.

[@BestCarFixes]

Yes, it's true that corrosion caused by moisture and dust is a common issue with SAM modules. However, it's important to note that the process of cleaning and applying protective coatings to the module can be tricky and should be done with care. In regards to your suggestion of cleaning and applying a thin layer of CRC urethane spray, this could be an effective way to prevent future corrosion. However, it's essential to follow the manufacturer's instructions carefully, as applying too much or too little could lead to issues. If the layer of urethane spray is too thick, it could potentially trap heat and cause issues with the PCB board. Therefore, it's crucial to apply it sparingly and ensure that it doesn't interfere with any airflow around the module. For each cleaned-up terminal connection, it's advisable to apply a small amount of dielectric grease to help prevent corrosion and improve conductivity. WD40 can also be used, but it's important to use it sparingly and ensure that it doesn't cause any issues with the electrical contacts. Overall, it's important to consult with a qualified technician or specialist to ensure that any maintenance or repair work is done correctly and doesn't cause further issues with the SAM module.

[@theidesofmarch314]

Thanks for this video, do you know if a bad front Sam can cause engine misfire? On left back side. Thank you.

[@BestCarFixes]

No

[@محمدالحجي-ف9م]

عمي انا حابب ممكن اتكلم في الحاله الا موجده عندي c300 2019 من علبه الفيوز الداخليه بتشتغل

[@KAZIUWICHURA]

hi, does a flooded SAM module affect the operation of the washers, wipers, ESP and airbags?

[@BestCarFixes]

yes for sure

[@KAZIUWICHURA]

@@BestCarFixes thanks for the answer. Is it certain that these components will work after replacing the module? I will also add that I will be transferring the module from 2013 to 2007

[@W204CommunityNG]

@@KAZIUWICHURAit should work. How did it go ?

[@KAZIUWICHURA]

@@W204CommunityNG it turned out that moisture was collecting in the fuse box after rain. I insulated it and I haven't had these problems for a year

[@manalyuae]

Brother , are you located in UAE? Where can i get the spare connector block

[@BestCarFixes]

No im in US

[@tonycastro6154]

IF YOU GET ONE WITH THE SAME PART NUMBER AND SAME MODEL,,YOU DONT HAVE TO DO ANY PROGRAMING,,JUST PLUG AND PLAY,,BUT LIKE ALWAYS DOUBLE CHECK EVERYTHING,,,A GAMBLE,,BUT SAVES YOU TONS,,,

[@Hebert6760]

The distributor boxes the wires have to go in a specific way or can be connected in any slot that fits?

[@BestCarFixes]

All connections has directions to fit

[@Hebert6760]

@@BestCarFixes yes one master plug that goes in the corner but the other ones that are the same can it be plugged in in any slot?

[@user-yq3te4wy1n]

@@BestCarFixes hi. My 08 c300 fan comes on high at all times and signal lights do not work all the time as well as the horn and wipers and some days they all work but the fan has been on high continuously so I took your advice and swapped that fuse box but the fan still on high any information would be appreciated on fixing this thank you

[@juniorsolis2010]

How do I release the 2 red wires?

[@johnkurtx4516]

Hello, will this cause my dash/instrument cluster to completely stop working causing no power ignition as well?

[@mjenks85]

I have this issue. Have you had it fixed?

[@mohamedtharwat2054]

Where is location in the car Mr mohamed

[@laloarmas6491]

My 2012 mercades c250 won’t start and has anti theft on the radio and and won’t read with the scanner and found water under the seats already changed the can buss and rewire still doing the same what can it be ?

[@mjenks85]

I have same exact issue. Does your cluster turn on? Mine is just blank.

[@adriancovaci8450]

Hello I have a merc e320 w211 2006 and my car not crank front fans start spining crazy and gear selector not want to move stay on p automatic car it may be from sam module I cant conect engine ecu and transmission to read codes it gives me no conection

[@BestCarFixes]

Check if there is a water inside

[@Man-Up-G]

You end up figuring out the issue?

[@nattyp7801]

2008 Mercedes Benz c300 hazard,fog lights and seat warmer don’t work….help

[@BestCarFixes]

get a good diagnostic tool and run a test to see what is the trouble codes says

[@nattyp7801]

@@BestCarFixes RU in the NYC area….

[@danbimmer4688]

Hi i need your help on a messed W177 Mercedes class A

[@BestCarFixes]

What can ido for you

[@danbimmer4688]

@@BestCarFixes do you have an email or WhatsApp ?

[@sohibgayed4349]

Mercedes cls w218 when connect OBD to diagnostic aromatic suspension , give me airmatic not equipped I can’t scan aromatic all fuse and relay good I need help please

[@BestCarFixes]

what year and module is it

[@sohibgayed4349]

@@BestCarFixes mercedes cls 2012 w218

[@ibrahimmeeran7735]

Brother, how to programe 2013 Cadillac CTS thru Autel i608pro

[@BestCarFixes]

What i know is to use the pathru inerface with a labtop go to acdelco tlc and buy subscription and program it

[@respectdabenz199]

Hello sir Are you located in Nyc?

[@BestCarFixes]

Yes I am

[@bighenriques]

Srs not comunication, c180 2006

[@BestCarFixes]

If your 2006 Mercedes C180's SRS module is not communicating, it could be due to a few reasons. Here are a few troubleshooting steps you could take: Check the connections: Ensure that all the connections between the SRS module and other components are secure and properly connected. Loose connections can cause communication problems. Check the wiring: Inspect the wiring leading to and from the SRS module for any visible damage or breaks. A damaged wire can cause communication errors. Scan the system: Use an OBD-II scanner to scan the SRS module for any error codes. This can give you a better idea of what is causing the communication error. Replace the SRS module: If all else fails, the SRS module may need to be replaced. However, this can be an expensive repair, so it is best to exhaust all other options before considering this option. It is important to note that working on the SRS system can be dangerous, as it is responsible for controlling the airbags in the event of an accident. Therefore, it is recommended to have a professional mechanic diagnose and repair any issues with the SRS system.

[@rohanboswell5408]

same circuit board

[@محمدالحجي-ف9م]

اي كمبيوتر عمي دا

[@محمدالحجي-ف9م]

هو دا موضعؤ بامانه

[@ousmanesarr7287]

Sam module jumper

[@BestCarFixes]

thanks

[@carelectricianwork7401]

Sir I am with sir

[@محمدالحجي-ف9م]

بالله ارجو التواصل

[@olandomeshack4827]

Dude just say Komputa for heavens sake whats with Compiura compiuter