2009-2014 F150 Rough Country 4" Suspension Lift w/ Upper Strut Spacers 2WD & 4WD Review & Install

[@americantrucks]

Shop This Rough Country 4" Suspension Lift: bit.ly/2oPWnzL Subscribe for New Ford Truck Videos Added Daily: bit.ly/ATFSubscribe

[@rickketchumn4458]

That hole he drilled with 5/8 drill bit was very close to the edge

[@gmarhevka2]

Was just thinking that.

[@infotechsailor]

I thought the same thing. A few comments here about that. Looked dangerous

[@warpedapple]

Seems to be the same on the other videos ive seen. Does look sketchy

[@jasonthomsen9724]

at 15:07 looks like he had to wallow out the hole further from the edge. Might have had the template in the wrong spot.

[@Another_Saved_Sinner]

He had two centerpunch marks to choose from, he chose the wrong one. Personally, I would have drilled my holes first, then adjust my cut line to leave 1.5× the hole dia to the edge. But what do I know? I just prefer my shit not fall apart while driving.

[@stevenwalsh6263]

It's not mentioned in the video, but I'd say it's important to put some paint on any bare metal once the cutting and drilling is done

[@P4X1279]

Whoever buys this lift probably won't have the truck long enough to worry about rust

[@bubbaslaughter]

@@P4X1279 why

[@LXIXTurner]

In other words, get this professionally installed

[@jayweathers9295]

Kingy B some kids know their stuff 😂

[@LXIXTurner]

@@jayweathers9295 sadly not *this kid* 😂😂

[@jayweathers9295]

LXIX Turner lol

[@justinjohnson8221]

@@LXIXTurner you watch this ten times and go under your vehicle you’ll be straight I just got done putting my lift on I bought the truck in September and ordered the lift the day after I bought the truck got it three weeks later the longest wait was getting time off to do it

[@JohnSmith-py9fx]

What would they charge for labor though I’d assume a metric ass load?

[@DRDRE-ex6yg]

I installed a 3 1/2 in leveling strut spacer with a 1/4 in Lean spacer ( extra 1/2 in) for a total of 4 in lift on my 2012 F-150 FX4, added a rear block, and my truck looks and rides great, with 35 in Yokos on 20's , so glad I didn't have to go through all that drama, and my truck is fully functional, even on off-road trails, so don't let anybody tell you what can't be done!!!

[@wesleylangford1617]

Hey id really like to see your truck and what amount of rear block setup you have.

[@miggylol]

Me too! I just bought a 2012 F-150 FX4!

[@tcdavis66]

not a fan of blocks, looks shitty

[@dennisforonda5706]

Control arms probably banging on the down travel

[@djleeks3407]

Finished the lift over the weekend. Thank you!

[@xrxckyx9210]

I was told to never double stack a Lift Blocks 🚫 but lift looks good I need to lift my 2010 F150.

[@TheScottfourty4]

Not gonna lie... that 5/8" hole that was drilled looked a little sketchy with how little steel was left on that top side.

[@brian644]

i thought the exact same thing.. NO WAY i would trust that

[@brayjohnny]

Wow.. I seen that and thought screw that I'd rather keep it stock!

[@mikehowes9]

he drilled the wrong punch mark. yes very sketch.

[@vincelacommare3839]

I seen that to

[@bobatbilletcreations]

Can you say step drill???

[@momakesmusic4646]

i did not expect this to be an HOUR 😂

[@edwardkareem6446]

I seen other professional shops install those rear shocks upside down just like the other competition shocks Fox, Bilstein and King rough country says to install them with the body facing down I noticed my truck was too bouncy so I flipped them around and no more bounciness

[@michaelescalante7718]

This dude be smilin through out the video, his vibe makes this video look easy to do 🔥🔥

[@LivinWith3M]

I’m a Readylift kinda guy but Rough Country has come along way. Nice vid.

[@americantrucks]

Thanks for watching! We appreciate it! -Zach

[@Baneslayer]

It's insane how easy you complete this complex procedure.

[@Detownrebel1]

I just purchased a used F-150 that already had a self leveling kit so I was researching a 4" lift kit to see if the extra 2" is worth it...I don't think so but my girlfriend said it would definitely be worth it if I added 2 inches to something else...Dooooeeee!

[@miggylol]

We could all use an extra 2 inches… on the truck too

[@IFIGHTNAKED]

She's a keeper

[@Wyoboy7220]

😂

[@Another_Saved_Sinner]

2+2........

[@bradf9249]

So no vacuum pump for iwe actuator on 09-14?

[@levsc9217]

14:14 that’s a little too close to the edge bud

[@JustMike2791]

That's what you get when someone who's inexperienced or simply doesn't give a shit. It could be both in this case, who knows? Cheap labor isn't skilled and skilled labor isn't cheap. You get what you pay for. The fact that they did it AND left it in the video tells me all I need to know about these yayhoos.

[@nopenada8071]

I’d considered that entire frame fucked by that point. Jesus.

[@adaz2525]

14:10 wtf..........: really

[@Marc757]

Singing a drill at high speed isn't the move here. Would have been better with a clean pilot hole and finished off with a step bit. More than likely that drill walked.

[@orangeisthabest]

You guys (mechanics) are fucking mind blowing cause man I swear I take some of this shit off my truck lol boyyyy let’s just say I ain’t gonna have a few pieces afterwards tryna put it back together

[@briandesjardins728]

just an FIY the CV nut is one time use, as well as upper balljoint nut too.

[@downlow5077]

little blue Loctite and your good

[@divorcedin08]

Don’t forget the alignment!!!

[@aarontyler6599]

This is a form of art.

[@Tazzspaz]

Following up on other comments on the screwed up bracket hole. Compare 12:21 13:37 14:20 there is definitely something sketchy going on. The template used at 12:21 is different than 13:37. At 13:37 the template looks aligned and punched correctly. But you can't tell where the edge of the bracket is relative to the desired hole. Then at 14:20 way too close to the edge compared to the desired location on template at 13:37 . The center of the final hole location also looks higher relative to the corner shown on the template at 12:21. That seems a huge issue for a structural modification.

[@VIDEOAIRBLADE]

Nice looks easygoing great job 👍👍👍

[@dalezegarelli5553]

Best install video on KZbin....GREAT JOB!!!

[@americantrucks]

Thanks for watching!!!

[@dalezegarelli5553]

@@americantrucks I'm doing a 6" rough country on an 06 f150, 4wd. You gave me the confidence I need to complete the job. I'm halfway there...

[@Leo-g3x]

Good work

[@derekbriggs191]

Is there a video with this lift except with the lifted struts?? I just bought the rough country full 4inch lift with the lifted struts instead of the strut spacers

[@crazybob1954mo]

Uhh, Not That Much Difference... If ya can't figure that out..... Put The Tools Down... Step Away.!!!!

[@LouisEmery]

This is very involved but very clear. But why the music?

[@international-arms-dealer]

shouldn't you wait until the truck is on the ground, with the shocks/struts loaded, before tightening them? wouldn't your way damage the bushings and such?

[@Another_Saved_Sinner]

Definitely would cause premature failure if not addressed, but since it needs alignment, I'd venture to say that they will all be reset while on the rack. Let's hope.

[@SteveLord]

Doubt it matters a lot, but the instructions actually call for the RC block to go on the BOTTOM, not the top. And that is how mine has been for years.

[@Car-lover245]

Just place my order Can’t wait

[@americantrucks]

Thanks Big Bro- appreciate the business! -Justin

[@Bingbangboom10]

Can i use rough country’s 2 inch levelled front struts with the spacers?

[@yourselfdotcomlol]

Someone just loves the sil glyde brake component lube. Just gobs of it on those pads.

[@thepioneer6178]

But how are your transfer case seals after some mileage?

[@ricmelyair]

Please answer to me soon how many inches is the block on the back for lift the rear please thanks

[@TheHeelyKid]

Would this be all be the same process if I was to get like a 7 or 8 inch rc lift if they make those?

[@AlexGarcia-cb6uc]

Great job 👏

[@americantrucks]

Thanks for watching! -Zach

[@IndyRockStar]

I just box Fox 2.0 front and rear suspension to level my 2020 F150. If I decide to lift it later will I still be able to use the Fox Suspension?

[@awroesch]

This guy seems pretty new

[@tcdavis66]

good job, looks great, personally I don't really like following all these lifted trucks. even with lower cost kit, your looking at another 3k for wheels and tires. Ya could be extra fun for mudding, but that is about it. I have mine leveled by lowering rear and performance tires, nitto 420's. happy happy

[@DoubleDiamondRanch2025]

Does it matter if I change the front shocks for the lift

[@jamesbiase2286]

with a 6 inch lift, do i need new upper control arms? or will they be level

[@tools4dummies]

😂 i just installed mine and the control arms are rubbing my struts

[@kismofer1]

i subscribed!!!!!👍🏻

[@kismofer1]

great video....good job .. every single step ..how too👍🏻👍🏻✌

[@DoubleDiamondRanch2025]

I thought the 4" lift came with steel braided brake lines? Mine has them

[@Noahide9]

On second thought, 3 out of 3 wrenches lol!

[@ricardosoto3810]

N now I'm going to lunch for a whopper n pay 10 pesos.😂😂😁

[@tommellos6056]

Dude, drill technique? How many rpm were you drilling that steel? Do you get one hole per drill bit? Slow and steady wins the race, buddy

[@bobatbilletcreations]

Should have used a step drill instead!

[@P4X1279]

And nobody stopped him

[@hectorlopez1344]

Rim and tire setup? 🤔

[@nineslot123]

I wish you guys would state if you have a 2 wheel drive truck your gonna have to have a factory 4x4 rear axle spacer as the 2wd uses no spacer and will have lean to the rear

[@fondlemeez]

I want install a lift kit on my truck but after seeing this video dang I'll probably die before it's finished

[@thepioneer6178]

Just go with a 3in suspension lift. It's way easier. The extra inch you gain from the 4in lift is not worth all this work.

[@kleimbach77]

if your going to do all that work go w/ a 6" lift

[@hugoreyes1051]

What is the size of the rear blocks?

[@phild9813]

Looks like a 2”, but not sure

[@jakeflores8273]

So do 35 inch tires fit on the 2wd version with only plastic trimming ?

[@mattward3812]

Did you figure this out?

[@jakeflores8273]

Matt Ward I never got a definite answer no they might still rub with plastic trimming on sharp turns if I were to guess

[@mattward3812]

Thank for the input!

[@phantom6799]

yeah my harbor freight impact ain't gettin this job done.

[@majorlancaster4598]

What happens if you put the lower end of the block tords the back?

[@crazybob1954mo]

It would cause the front and rear universal joints to be at different angles. This would introduce driveline vibrations and cause the universal joints to fail sooner.. >;)

[@YourDome_]

What about a 2006 f150 xlt

[@IndyRockStar]

I don't understand why they don't powder coat knuckles from the factory.

[@TheSun_89]

Looks like a pain in the a$$ to install.

[@Kentucky-ev7bd]

I know you added a spacer on the drive-shaft, but wouldn't 4" drop put big-time strain on that front at the differential and at the upper end?

[@eddiecastro5088]

Dam son what else can you do

[@daniellutringer9519]

What overall height would a 3” or 4” lift with 35” tires yield on a 2018 F150? Would anybody know that info?

[@Ohsee83]

I have that exact kit, 4" lift with 35's. My truck ended up being 6"8', if that helps bro.

[@bhadd3418]

@@Ohsee83 Did you do any trimming?

[@nemesis851_]

Good content BUT HATE 2 second music looping for 54 MINUTES - drove me INSANE

[@tevanlowe9310]

Does it drop your mpg??

[@americantrucks]

You could definitely see a drop in your MPG after installing this lift kit since your aerodynamics will be changed. -Zach

[@lilstevo74]

Truck skipped leg day without some new 17's with 35's

[@tommellos6056]

Let the real mechanic make the video next time

[@erich6183]

**WARNING** DO NOT ATTEMPT INSTALL IN RUST BELT

[@samsungfan1041]

If I saw that thin piece of medal I’d be legitimately scared to drive it

[@SRTleako]

Where can i find upper strut spacers?

[@IdioSyncrasy1337]

They should be an option when you order their lift otherwise idk

[@dawsongreen988]

anyone know where i can find this but for a 2010 4wd?

[@flman1284]

You just watched it. ..

[@kleimbach77]

the steering is different on the 2014 trucks

[@JesusF150]

Hi my friend I just made a 6 "RC , new 35s on 20x12 wheels and tires, but I have a problem, when I pass 65 mph it starts shaking 70+ is worse, with your experience Do you think it is a problem with the RC suspension or with a new alignment and balancing will solve the problem?

[@pro-impulse2831]

That’s definitely your tires bro lmao

[@JesusF150]

@@pro-impulse2831 it was the wheel spacers, not the tires.

[@morganverizon1]

Unless your 100% proficient fully with all the tools and processes pay a professional 4x4 shop

[@IFIGHTNAKED]

So is no one gonna talk about his tattoos? They're fuckin nice man js

[@BlakeKillam]

Or you could just level it and put on the 35s and it’s basically a 3.5” lift for half the price.

[@noonce]

Tell me more because I can't afford this haha. What leveling kit would you suggest?

[@downlow5077]

Sure but you fuck your cv angles

[@UnC1v1Liz3d]

With this kit are u able to return to stock if desired? Any cutting?

[@danielwalker2874]

Nope. The cross members have been cut off. It’s permanent. Now you can go up in lift size but this is as low as it can get.

[@tomchryplewicz1360]

Nice video but dear God get rid of that background music!

[@Another_Saved_Sinner]

14:24 jeez, no meat left on the outer edge of that hole. Better hope the customer never sees this video!

[@TheIzzandrew]

This shits funny, he labels this a 2 wrench difficulty but a 2 inch lift kit that only requires 2 hours of labor is a 3.

[@kathystokes8534]

where is the before and after pic????? WTH

[@americantrucks]

At the 0:05 mark of the video! -Zach

[@airlogitecQ-electrical]

great job

[@americantrucks]

Thanks for watching! -Zach

[@victorsolano7777]

You did all of that and you didn't even show it how it looked like at the end? Hello🙄

[@americantrucks]

We show you how the truck looks with this installed at the beginning of the video. 👀 -Zach

[@glee1804]

Is hard to find shop will do this with out fk up you truck... find a good shop is hard part

[@vincelacommare3839]

All that and u use stock struts that's y they suck

[@98flstc]

Looks like a good way to ruin a perfectly good truck.

[@americantrucks]

Different strokes for different folks! Thanks for watching! -Zach

[@TheIzzandrew]

Hes not a real mechanic real mechanics swear every other bolt

[@robertw1871]

Do away with the music and the over-enthusiastic bouncy pace…. Get the feeling the narrator has never even held a wrench but is just reading a script….

[@adriansims1596]

Rough Country is junk.

[@ineedabeerandaliedwn]

adrian sims looks to be comparable to other strut spacer lifts.

[@moose1164]

Absolutely agreed buddy. I don't know how they are still in business. Their quality is piss poor to say the least. I think it's hilarious when people put a cheap lift on an expensive truck. I got a 6" Pro Comp on my 2018 and it rides smooth as stock.

[@kleimbach77]

pro comp is junk too

[@Leo-g3x]

Good work