2010 Chevrolet| Camaro ss| Oil Pressure Sensor| Replacement

thanks for checking out my channel any questions or anything you guy's think🤔I could do better on please leave it in the comments below and thanks for watching

[@theviperkiller-io5ji]

Nice we got more videos on this oil pressure sensor thanks bro.

[@h.a.bgarage1008]

Thank you 🙏🏿

[@theviperkiller-io5ji]

@@h.a.bgarage1008 no prob how much you charge for a starter job.

[@gabrielferrar6996]

Beware guys the ls3 does not come stock with the filter I sat there for 30 minutes trying to get a filter out that was never there! Great video tho

[@h.a.bgarage1008]

I wasn't aware of that he did buy this car from a used dealer I don't know what number owner he is I will have to ask him but thanks for the information

[@oscaralmanza1451]

Bro same I’m in the middle of this and I couldn’t find a filter lol

[@ATFispoopoo]

Immensely helpful video. They wanted to charge me and my wife 400 bucks for this. Doesn’t look like a 400 dollar job tbh.

[@h.a.bgarage1008]

They charge you that much because they take everything off around it and then they get to the part

[@h.a.bgarage1008]

And thanks for watching🙏🏿🙏🏿

[@gdupmilli5825]

Thank you my SS brother

[@h.a.bgarage1008]

No thank you for Watching

[@gabrielferrar6996]

Also I noticed on the start up it said you didn’t have oil pressure still is this because it’s a newly installed switch? I installed mine and started it briefly to see if it was fixed and it was still reading 0 oil pressure on start up so I shut it off immediately to stop any damage from occurring.

[@gabrielferrar6996]

Figured my whole pump was out, it wasn’t throwing any codes about oil pressure or the pump being bad so I figured I would try the sensor first

[@h.a.bgarage1008]

@@gabrielferrar6996 That's a smart way to think a lot of people always think the worst and most expensive problem first and then when it's not that they panic

[@gabrielferrar6996]

@@h.a.bgarage1008haha ik wym but should it take a couple of minutes for the oil pressure to show on the gauge or something? Like I said he showed the oil pressure was at 0 and said “let me wait for it to get warm” obviously it shouldn’t have 0 oil pressure just because it’s cold so does it not read right away because it’s a new switch?

[@gabrielferrar6996]

Anyone that had the same questions as me the only smart thing to do is put a mechanical gauge in the oil pressure switches place and see if it has any pressure. you could probably do this by cranking your engine with the ignition and fuel injector fuse pulled out if you’re worried about starting the engine and causing damage

[@dtdascl]

I hate sensors 😂 I'm gonna call you next time

[@h.a.bgarage1008]

Thanks

[@PlymouthBarracudaV8Hemi]

Does this sensor show the current pressure? I don't really trust it

[@h.a.bgarage1008]

Before I put the sensor in with showing it didn't have oil pressure switch off the computer that it didn't the sensor doesn't control the oil pressure it just controls the fact that the computer knows it has oil pressure so on the dash in the car the oil pressure was shown as very low

[@h.a.bgarage1008]

Like the needle was barely responding that the car has oil pressure it was very lamp

[@chadbair9265]

Is this a v6 or v8 2010 ?

[@h.a.bgarage1008]

@@chadbair9265 thanks for watching the video and commenting but to answer your question it is a V8 2010 Chevy Camaro

[@ggtv744]

👍🏿👍🏿

[@h.a.bgarage1008]

🙏🏿🙏🏿🙏🏿

[@luck1of1]

How did you get the old filter out

[@h.a.bgarage1008]

Are used a are used a Phillips head screwdriver and stuck it in there and the filter came up

[@caleblsreal5295]

It funny he never show the socket he used

[@h.a.bgarage1008]

You are correct I did not show that but you can use a 27mm deep well socket that should work

[@ernieobrien7733]

🤤 *promosm*