How to video replace back up camera 2011 Ford Edge with aftermarket camera purchased for $53 on eBay.
Пікірлер: 72
@rebardon6 жыл бұрын
I just replaced the camera in my 2011 Edge. There is a way to get the camera out without cutting that tab. If you look to the left of camera in video you will see a small dimple. Just up and to the left of that you will see what looks like a silver dimple inside a larger black raised circle. I paused the video at 2:49 and it shows a good view of what I'm talking about. The black dimple is a positioning dowel to line everything up during assembly. The silver one is a screw or rivet that is put in from the other side during assembly to hold that plastic bracket in place. If you drill this dimple out the entire bracket holding the camera in place can be shifted to the left and removed. I took old camera out , installed new one and replaced the bracket. The hole left from drilling that screw or rivet out leaves a place to put a sheet metal screw in that will now hold that bracket in place. This video got me going in the right direction getting to that camera but I didn't want to cut that tab so I found a different way of doing it. Hope this helps someone!
@russellallen62874 жыл бұрын
Where did you order your camera?
@sbstnct3 жыл бұрын
Thanks so much! My camera was from amazon and was like $110 something. Took about 45 min with the help of my 12 year old daughter. Thanks again!
@theresagibson10423 жыл бұрын
Did you have to get it programmed at the dealer to make the lines appear on the camera screen? Thanks
@sbstnct3 жыл бұрын
@@theresagibson1042 no you just plug in and it works.
@JoshPowell813 жыл бұрын
@@sbstnct do you have a link to the one you purchased?
@davidmorrison51866 жыл бұрын
Thanks fixed mine today. Had to do all your steps.
@ckperk246 жыл бұрын
Thanks Chris! Great video! I was suffering with a cloudy backup view for years, now nice and clear! I agree with Chris' approach to trimming the tab (...seemed way too difficult to remove the torx screw). I also made a couple mods: I used my Dremel with the small sanding drum to trim back the opening in bracket to allow the camera to easily fit in. Then I made a small aluminum angle (.75 wide x .75 legs with ~110 degree open angle) and attached it with a small sheetmetal screw to the area where tab was removed...held the camera nice and tight.
@jmarkutah3 жыл бұрын
Just remove the torx screw.
@PapaVrooom5 жыл бұрын
You don't need to break the tabs to do this. The four outer studs are threaded and the entire piece pops out.
@josevelez40763 жыл бұрын
My friend excellent video we fix my 2011 Ford Edge follow your indications on the video thank you
@jimjost66855 жыл бұрын
Chris, I have the same problem with my 2012 Ford Edge. What is the part number of the camera that you bought?
@georgedold22886 жыл бұрын
The t-20 torx screw is easy.... all you have to do is remove the blue oval (pry up on one of the holding tabs on each side and use a door removal tool to coax it out) and drill a 1/4" hole opposite the screw through where the blue oval will hide it. If the panel was on the car, and you are looking at it from the back, the hole will be directly below the left mounting hole for the oval near the edge of the oval. The t-20 tool is at a slight angle but removes the screw without any hassle.
@rogerbritus93782 жыл бұрын
That's how Ford does it by their TSB
@scottswail11456 жыл бұрын
I am going through same. thing in my 2012 MKX. Dealer wants $1,100. As well, after I updated the software two months ago, now my camera, which works occasionally, went upside down and occasionally the screen will not allow me to change (e.g., go to navigation; go to radio). So, without updating the software, they said they had to replace the computer component for the screen. Another $1,000. I don't buy any of it.
@Gloch94 жыл бұрын
Do you have a link to the camera?
@extremediver716 жыл бұрын
thank you !
@taterjay2 жыл бұрын
If you remove 4 of the bolts out of the panel, you can release those clips and open the whole thing up. Then there is a torx head bolt that holds the camera bracket in that way you don't have to cut anything.
@scottswail11456 жыл бұрын
Can I ask which item and site you bought it from? There are a few and I'd rather buy one that has definitely worked.
@bobabuhi706 жыл бұрын
Do you have to take your car to the dealership to program the system for the new camera to work? From the video I would say...NO. But I heard that you have to have them program your system for the new camera to work.
@kf4wnf4 жыл бұрын
What model camera did you purchase? I can't find any model for the Lincoln/Edge for $53 or even remotely close to that price. Most are $250+. Please do share which one you found that works. Thanks!
@roncappellini8846 жыл бұрын
pause it at 2:27 and you can see the screw next to your thumb, remove it with a chapman tool versus cutting the bracket
@codingarchangel21625 жыл бұрын
pls link to where you brought the car from....thanks
@OnlyJosh095 жыл бұрын
I noticed where you bought your camera they only had one available for that low price. Now I can’t find it anywhere unless paying $130+ which is crazy to me
@roncappellini8846 жыл бұрын
nice video....only recommendation 2:33 is do not cut the plastic bracket to remove the camera...there is a t-20 torx screw that should be removed so you dont destroy the braclet that holds the camera....its a pain but doable.
@wonStarReviews6 жыл бұрын
Ron Cappellini how do you get to that screw? Looks inverted so you can't get to it unless you remove the whole emblem frame behind it
@roncappellini8846 жыл бұрын
Chapman tool with a t-20 torx bit. Its a pain... remove the license plate bulb enclosure for added room....hard to explain but you work it from the back side blindly....it takes super powers, just kidding. Take your time and dont give up....
@Dumpsterbroz5 жыл бұрын
I later found out how to take the whole assembly apart. The video is a bit long but has good information I wish I would have had when I did mine. kzbin.info/www/bejne/gKucpJuhobVrfrM
@wrb2bones5 жыл бұрын
kzbin.info/www/bejne/gKucpJuhobVrfrM
@justinncherish4 жыл бұрын
Chris Brems how is the camera from eBay holding up?
@andrewpropes36465 жыл бұрын
What was your diag process to isolate the problem to a bad camera? How did you eliminate switches, wiring, modules, etc.?
@adamt71425 жыл бұрын
Andrew Propes this is what I want to know
@deborahwillard6325 Жыл бұрын
Mine works it's just cloudy when I get close to stuff it beeps should I pop the lens out and gently clean it right let the cam air outin the meantime my manual is in french so idk
@ChrisNH2FL6 жыл бұрын
Did you by chance calibrate the camera to work with the vehicle? I replaced my camera in our 2011 Ford Edge and now I’m not getting the guide lines.
@Dumpsterbroz6 жыл бұрын
I didn't calibrate. When I bought my edge the camera was broken so I didn't miss the lines. If you find out how to calibrate please let me know the process
@pollorobot696 жыл бұрын
Download Forscan For This Is Very Easy
@ChrisNH2FL6 жыл бұрын
pollorobot69 actually tried that and when I went to follow the process it kept saying I needed to do a self test for DCT(DTC) errors. I couldn’t get around it. Found that all kinds of people are having the same issue on their Ford Edge using FORScan as well. I wish I could get past this as I need to restore the guidelines as well.
@genestrelkov98865 жыл бұрын
As a Ford tech. I can tell you every time I replace a camera it needs to be configured with Ford scanner. I don't know of any other way to get the guide lines after replacing camera
@mikep93295 жыл бұрын
Just a quick question..did u try a sync master reset prior to doing this
@nubliniwaserfaztman71194 жыл бұрын
What is a sync master reset??
@jlcastroK5 жыл бұрын
Hello Chris, do you have the link to buy one of this ? I just see the OEM ones on eBay !!
@OnlyJosh095 жыл бұрын
There’s no more available
@enriquerodriguez64524 жыл бұрын
You have to open that lead man to avoid any damage
@roncappellini8846 жыл бұрын
Screen Shot 2018-05-02 at 10.41.20 PM
@russellallen62874 жыл бұрын
Where is the link on what camera to buy everyone I find says not compatible with the 2011 edge
@TXRSEFLWR4 жыл бұрын
Call your Ford dealer or A Ford dealer and get the part number that is what I did. And I also found the price for the Lincoln camera was more than ford but the part number was the exact same. I found mine on Ebay sold by a Ford Dealer in CT.
@victorcholak98635 жыл бұрын
Hi Chris! It’s been some time I know that you may not have the link to where you purchased the part but if you do it would be a big help
@ebaugnet63595 жыл бұрын
Also interested in this
@OnlyJosh095 жыл бұрын
He posted the link at the beginning here but no more are available for so cheap
@nubliniwaserfaztman71194 жыл бұрын
Me too Chris
@Dumpsterbroz6 жыл бұрын
www.ebay.com/i/162677776603?chn=ps That is the link where I bought the camera. Also this is my first video so go easy on me. I will keep the orientation the same next time.
@emii42335 жыл бұрын
Did your rear parking sensors still work when the camera was disabled?
@pitbosskev4 жыл бұрын
Edward Miller II mine do.
@Misticzerx0r5 жыл бұрын
You can use some software called forscan to recalibrate to get the guide lines and turning if your vehicle had them. However aftermarket cameras usually don't calibrate I tried a cheap one didn't work had to buy the official Ford one to make it work like new again.
@rogerbritus93782 жыл бұрын
Great tip! I noticed that the lines didn't come up when he put in reverse
@cghrios783 Жыл бұрын
Please how much was the original replacement camera? Thanks
@ChrisNH2FL6 жыл бұрын
Good vid good tutorial, I know it’s only been a month since you posted this. How is the camera holding up for you? Are there any “lessons learned” from doing this yourself? Anything you could/would have done differently? I am in the same boat with my 2011 Ford Edge Limited. The stealership wants almost $500 to replace/repair ours.
@roncappellini8846 жыл бұрын
you do not cut the little PITA clip....there is a t20 torx that needs to be removed...
@rickybobby66785 жыл бұрын
Just finished replacing my camera, i went a differnt route but used a 50 dollar replacement. No lines now. Anyone figure out how to fix it ?
@OnlyJosh095 жыл бұрын
Link to camera???
@rickybobby66785 жыл бұрын
@@OnlyJosh09 looks like they jacked the price up. Im not seeing the one i ordered. Cheapest one i see now is 150. Got it from ebay
@@OnlyJosh09 this may work ? www.ebay.com/itm/OEM-FL1T-19G490-AC-Rear-View-Fit-Ford-Edge-2011-2013-Backup-Cam-Parking-Assist/323755300345?fits=Year%3A2012%7CModel%3AEdge%7CMake%3AFord&hash=item4b6151d5f9:g:yZQAAOSwUu9bTqF4
@robertjones75654 жыл бұрын
Try this with the engine running Go to Settings- vehicle rear view camera turn off-- camera delay park aid delay guidelines Put the transmission in reverse to see if the camera works then turn back on the three items you turned off.
@user-zy7sv3xh6p6 жыл бұрын
Chapman tool and a t-20 torn bit. It a pain.
@roncappellini8846 жыл бұрын
torx bit
@mariopina7462 Жыл бұрын
Can't hear you need volume higher
@jordancobb5095 жыл бұрын
Thanks for skipping over how you detach the wiring. Why would you not explain that ?
@Dumpsterbroz5 жыл бұрын
Jordan Cobb sorry bro fairly new to making videos.