2013-2016 Ram 5.7 Hemi evap purge solenoid replacement

[@eliyahomar]

I just canceled my auto service appointment . i was supposed to go today to get it replace the auto service told me it will cost me $160+tax for the labour work only you just saved $160+tax as i was able to do it myself Thank you so much for your video

[@dalegribble60]

Thanks brother! Your instructions worked like a tee on my '16 Ram. I didn't think I could do it in the same time frame seeing I didn't have a 5 foot screwdriver but I did. The big thanks are to those clamps....drive me nuts! Never know if you lift, push or squeeze. Also note, I removed the old valve and could blow through it. The new one you can't.

[@MotorCityMechanic]

Thanks Bill for the comment and for watching. Simple fix as you saw and not hard to replace

[@-greenheat-]

Thanks for the helpful video. I just replaced mine; it was one of the easiest car repairs I've ever done. Couple of things I learned: 1) At 1:28 you can use a regular flathead screwdriver to take the hose clamp off by going underneath the 2 A/C lines, rather than between them. 2) At 1:42 on my '17 there aren't rubber gaskets for the air hose, it seals directly on the plastic. It was stuck on there real good. It was easier to break the airbox side loose first, which gave me leverage to rotate the entire air hose to break the intake manifold side loose easier. Once off I recommend cleaning the sealing surface with WD-40, to ensure it seals when you reinstall it. It also makes reinstallation much easier.

[@daltonrenick5184]

Very helpful, I assumed the worst when my check engine came on. I thought for sure my transmission was on its way out but this is the code that ran on the computer. With your video, if this is the problem, I can now fix my own truck for about $40 and about an hour of time. It'll be an hour for me because I'm slow as hell when it comes to anything larger than a 2 stroke engine.

[@colettewhite]

Thank you for making this video! You helped me replace my purge valve this morning. You made it easy to understand. The whole process took less than 10 minutes. My truck is running soooo much smoother… thank you, again, for this video!!

[@thelasvegassportstalk]

that's correct less then 10 minute job.

[@asdfqwerty271]

Quick and easy once I found it, on my 2014 ram 5.7L. Great video, thank you for making it so easy to understand. I hunted around for an hour on my gas tank to figure out where the evap cannister was, but found it under the hood thanks to you, haha.

[@MotorCityMechanic]

Glad you got it located. Thanks for watching and for the comment. Dont forget to subscribe.

[@davem7312]

Me too lol

[@James1987F]

Thanks so much for this video. I followed it step by step and replaced this within 10 minutes! I never would have figured out there are fingers under the red lock that realeas it.

[@bluebox212]

Way to go, my friend. I can do this for my uncles truck now with confidence after watching your tutorial.

[@michaelgreen1371]

Just a heads up on you guys that get a p0456 on your rams. Mine is a 2014. I was getting the code and thought it was maybe the gas cap but i wasnt getting the gas cap light. So i checked all the lines. Turns out it was the line going from the silinoid to just right by the throttle body. It looked like it was on but i pushed down on it and it slide down just a little. It doesn't even have a clamp on it. just that tiny fraction of being loose was throwing my code. Now no more code.

[@MotorCityMechanic]

Thanks for that added info. Its always cool to see viewers helping viewers. Glad you found the cause of your code.

[@davidgamez7967]

Me too. I had the P0456 in a 2015 Charger V8 and I was able to push down just a little on the fuel vent line that goes to the throttle body. Erased the code and haven't come back in 24hours. Now, I don't know if I should return the canister valve or keep it as replacement. ( part PV749 at autozone)

[@mlaugh3]

Do you mind telling us what motor you have they're not all the same.

[@Psyquek3o]

Hello I have same code, P0456 in a 2015 Ram. Will try this and let you know if this works.

[@barrybebenek8691]

Mine was exactly this. So glad I found your post. Closed the hood one time, and bam...the code. I put a small hose clamp on loosely (it’s just plastic there), and won’t happen again. Cheers. 👍🏼🇨🇦

[@lindar6588]

Excellent video. I got it done in no time. Thank you!

[@InstinctBassin]

Thanks! Followed along perfectly. Taking the sensor off the big air hose was a little different on a 2016 but just needed to be turned to the left and then pulled off. Otherwise perfect instructions. Hope it finally gets rid of the check fuel cap light that keeps coming on!

[@JoseRodriguez-nl7vs]

Very good explanation thank you

[@MichaelJonesskinnerjphotos]

Just changed mine out took about 15 minutes. Hardest part was getting the damn cover back on. lol. I'll update in a few days on if it "cured" mine. Thanks for a great instructional video.

[@MotorCityMechanic]

Thanks Michael! Glad it all worked out in the end. I so want to throw those engine covers in the trash each time I work on them.....guess the engine isnt pretty enough to the eyes that we have to cover it up and use it to dampen some of the engine noise as well. Make sure to subscribe and hang around to check out some of my other videos.

[@bretttuttle9399]

How much was this pRt. And where did you get it if you dont mind me asking

[@fredproctor7239]

Micheal, it's been 8 months since you posted and you said you'd "update in a few days on if it "cured" mine." So what was the outcome?

[@TejasToolMan]

Fred Proctor parked in street broke down lmao

[@f14tomcataocretired95]

Super Instructional Video! Down & dirty and to the point with none of the overthinking BS you see other people do. BIG THANKS! I'll have this done on my quick thanks to this well documented video. Suscribed to your channel and standing-by for other info from ya. Have a great Navy day!

[@katydidnt3906]

Best video out there on this replacement. Mad gratitude

[@larryl5829]

Thanks, It was well explained and it really was easy to install, but I couldn't have done without you!

[@therealGrimRemembrance]

Solid video, easy to understand and follow along. Down side is I don't know that this will fix what I'm dealing with. I have a P0455 code (EVAP system leak monitor, large leak detected). Any suggestion? Odor comes from near the gas cap/fill area. No fuel leak. New gas cap put on, did clear out the code. Occasionally the gas cap light will turn on, then turn back off after a few minutes. Loose connector? Loose hose? This did start after replacing the fuel level sending unit so I dropped the tank and disconnected everything. Put everything back on after, but maybe not tight enough?

[@ryeweskey]

I was told at a dealership to take some fine grit sand paper and see if you can clean up the lip of the filler tank. Where the gas cap seats. It gets sort of corroded there I guess. Might be something to try. Just a quick sand to clean up any of the Junk they said.

[@cliffordpayton5517]

ON MY 2010 RAM 1500 4X4 SPORT WITH HEMI, ITS LOCATED AS YOU SAID, NEXT TO THE BATTERY, JUST BELOW IT. I JUST GOT THE SMALL LEAK DETECTED, FOUND THE PART ON AMAZON FOR $20. HOPE THIS FIXES IT, JUST CAME ON THIS MORNING.

[@MotorCityMechanic]

Thanks Clifford for the comment. Hope it works out well in the end. Thanks for watching and make sure to subscribe.

[@cliffordpayton5517]

@@MotorCityMechanic Yes sir, I installed it in 5 minutes, disconnected the battery for 1 minute, started it up, light went away, and has been off so far

[@MotorCityMechanic]

@@cliffordpayton5517 Awesome. Time will tell, I will keep my fingers crossed

[@thelasvegassportstalk]

Thank you sure you just save me $200.00 . I said I'm not paying for something you just plug in item. Thanks again for posting this video. Las Vegas thanks you.

[@bigbearbland]

Great vid, did my 2017 in under 5 mins thanks to you. Good on ya mate.

[@MotorCityMechanic]

Awesome.....now thats quick. Thanks letting me know how it went. Make sure to subscribe if you havent already

[@bigbearbland]

@@MotorCityMechanic There was only one thing you left out. I disconnected my battery afterward for 5mins to reset the comp and have the check engine light go off

[@MotorCityMechanic]

@@bigbearbland On the battery you can do as you mentioned and then the other thing is not disconnect and if you truely fixed the issue then over the next few days the light should go off. Thats one way to know you got it right. Either way you cant go wrong.

[@Blitzem2787]

Thank you so much boss! P0456...this video was very well done and so easy to understand!

[@MotorCityMechanic]

Many thanks for the feedback and kind words.

[@lincoln6981]

I just got this ram with the same code too. Wanted to try just replacing the gas cap at first but seemed to come back on. Now replacing the purge valve

[@classentransporthotshot1496]

@@lincoln6981 what was the symptoms u we’re having?

[@lincoln6981]

@@classentransporthotshot1496 no Symptoms actually just the check engine light. I already replaced the purge valve. And even taken a trip out of town ( 300 miles round trip ) and everything is good now 👍

[@tonywann7657]

Excellent instructional video! Thank you for sharing this information.👍

[@andywoolsey6457]

I have a 2013 ram 1500 where is the evap purge solenoid at it not on the side of the throttle body

[@Jason-nw7wn]

Thank you for the video. Saved me time and money. My check engine light is still on after replacing the valve though. Will it go off on its own or do I have to reset it manually?

[@JesusPerez-cm6fp]

Disconnect the negative battery terminal for like 45 sec. It’ll come off. If it comes back on, something is wrong still

[@ridervalerie4]

Thanks for sharing this it helped me with changing mine

[@MotorCityMechanic]

Glad I could help in some way! Thanks for watching and for the comment

[@richpingston238]

Great video. Exactly what I needed to see to fix mine

[@MotorCityMechanic]

Appreciate the comment and glad the video helped

[@tyrellgatling5666]

Is this the same as p0441? My check gas cap light popped on yesterday. Tightened cap & reset code with obd reader & code didnt go away. I keep my truck over half full & when i feel it i stop when the pump clicks once. No gas smell or nothing like that. Whats your suggestion? I hate dash lights 😡

[@MotorCityMechanic]

The code for the gas cap cant be cleared.....a test has to be run to make sure there are evap leaks and if it passes, you can then clear the code. If tightening the cap was the fix then it may take driving it for awhile and at least one fill up of fuel for it to run the test itself and store the code so that you can then clear it.

[@tyrellgatling5666]

I changed my gas cap because the o ring waz dry rotted & it cleared after i disconnected the battery for 10min

[@MotorCityMechanic]

@@tyrellgatling5666 So much for what I said lol. Typically they wont clear easily. Glad you got it worked out in the end an I will need to remember that as another option next time. Thanks for replying back Tyrell!

[@davelazarick9899]

As previously mentioned, great video, thanks. One question, I see that there are some options to buy a replacement solenoid only without the hose and to just re-use the existing hose. Cuts the price down by almost 2/3rds. Is it ok to use the old hose? Thanks, again!

[@deborahmason4459]

This looks easy. Gonna try it and hope it’s the fix.

[@bernarlitt17]

This video is only for ram 2014-2016. The 2013 ram solenoid is under the battery and looks different

[@MotorCityMechanic]

Pulling up the Chrysler factory service info....it shows it to be by the throttle body on the intake for the 3.6 and 5.7.....now the 4.7 is located under the battery. Not sure if we are speaking of different engines or if the service info isnt correct. I will certainly try to see next time I have one come in that happens to be that year. Thanks for the comment and make sure to subscribe.

[@mikee3997]

Thank you had check engine light on had checked and found part was 27 and found video I think I can handle it

[@tufffireguy]

Where else would I find this? I have a 2015 2500 5.7l but it's not where yours is, I've checked on and around the gas tank and have looked everywhere with no luck.

[@bobbyntammy]

Thank you... You showed me how and saved me $.

[@MotorCityMechanic]

Glad I could help out. Make sure to subscribe.

[@falconsfan96]

Does the evap make any form of noise under the hood while truck is running. The noise happens for like a min and then stop then take a min or two then starts again. Any clue of the noise.

[@MotorCityMechanic]

It can make a tapping noise when its working......I would make sure that its the cause and not a bad HVAC actuator under the dash. Typically you wont hear the purge solenoid inside......only outside and mainly with the hood up. Thanks for asking and make sure to subscribe.

[@snap1966]

If this solenoid is bad, does it make a popping sound when the engine is running and idling when you start it.

[@chadcrane5400]

So I have a conundrum.. I have a 2013 Ram 1500 5.7 hemi 6 speed automatic. And the purge valve is not where you're showing it?!! Maybe I've gone blind, but where the hell is it?

[@chadcrane5400]

Tom Strubbe I have not found out yet... I'm thinking on top of the fuel tank??? But I can't get there.

[@Justin12833]

@@tomstrubbe5551it’s under your battery…he says it in later post.

[@Daryl3737]

Great video. Do you know if this replacement process is the same for a 2016 Ram 1500 (6 cylinder?). Many thanks

[@Jason-nw7wn]

Not sure if you still need an answer to this question but I just changed mine on my 2016 and it was the same other than me having to use a flathead screwdriver vs a Phillips

[@gnickolas69]

So I have a 2013 dodge charger. I had the smell of gas or fumes in my engine cabin. Thought it was the fuel tank or the the pump. Took the seat off smelled fine no leaks and I can hear the pumps turning on. So a month later I got the p0456. Said evap leak. Did research found that it could be this part. Or the canister which is under the wheel well. Would that cause the smell though? I read it can. But I'm thinking if my best bet is just to replace both since I check the fuel tank already. I found it could be the filler neck. But no smell there. Also the smell went away after a while but comes back faintly.

[@allaroundperformance]

On my 2013 tradesman it’s not located there you think you have an idea where it could be I’ve had the code come on and of and it’s showed the purge valve and the solenoid

[@jasonwilczewski2741]

Looks like no one has posted anything recently, hopefully someone can help me. I have a 2018 Ram 1500, having problems putting gas in the truck. The gas pump continually clicks off everytime, dealer replaced filler neck, canister, and vent hoses. Same problem, could this Evap Vent Solenoid be causing the issue? Ive read that if the pump keeps clicking, this could be the problem. If it is, is there something i can do to fix it other than Having to deal with it till it gets back to the dealer? Maybe check lines from it? Thanks alot

[@jasonwilczewski2741]

Turns out i brought to dealer, after the filler neck, canister and vent hoses, they replaced the gas tank and all is well. Just shocked me that a gas tank on a new truck just gets messed up like that. Dealer had no explanation, more like well beats me.

[@patrickupshaw7379]

Thank you for the information

[@oneloveking49]

I have a check engine and gas cap light on. I replaced the gas cap about 5 weeks ago and still wont go away.. I went to autozone to have the check enginelight checked and theres no code. But all it says in the msg is (small or larger gas leak).. and i keep getting a strong sent of gas.. Could the evaporatin vent solenoid be the problem? I have a 2014 ram 1500 with the 5.7 Thanks for the help in advance..

[@MotorCityMechanic]

When it comes to EVAP leaks.....an external machine will need to be hooked up and the system tested to see if it will hold pressure and then smoke the system if needed to help locate the leak. Otherwise you will be guessing and throwing parts at it.

[@kennethtraylor6766]

Thanks David for the info

[@bluebox212]

How could you test that part once taken off so as not to replace a part that is not the peoblem?

[@jurpikag]

Hello. Got to this video from googling my issue. Any advise would be awesome. I have a 2012 RAM 1500 5.7. PO443 is triggered but its not the valve. What have you seen as the most common place to go next on these? usually the wiring or the PCM itself? Thanks again.

[@rome9299]

So I have a 2016 Ram 1500 w the 5.7 and mine seems to be ticking is this normal?

[@MotorCityMechanic]

Rome Wild if your speaking of the purge solenoid then yes you can expect some noise from it.....clicking off and on when it’s activated. Thanks for watching and for the question.

[@penguin99ify]

Question: Where exactly is the Purge Control Valve, P/N 25014001, located on a 2015 Dodge Durango? I had a MIL light illuminate and code P0456 came up on my BlueDriver analyzer. I had the dealer perform safety recall U65/NHTSA 18V-332 to reprogram the PCM which is a fix for said code. While there the dealer claimed they replaced aforementioned valve. However, I saw no evidence of any tooling marks on screws or finger prints in the fine dust which covered the entire engine bay i.e. nobody touched anything there. Luckily the car was under warranty and there's no complaint. Just verifying the valve's location for curiosity.

[@MotorCityMechanic]

What size engine?

[@EscobarMT]

Did u disconnect the battery? Thanks

[@scottisbell8997]

I have 2013 Ram 1500, it’s not in same location as 2014,any idea where it’s located ?

[@markusfarkus1478]

Anyone know if it’s safe to reuse the hose? Auto zone had two models to replace. One with a hose for 50 one without for 22

[@MotorCityMechanic]

As long as the hose looks good.....I say go for the one without.

[@ml-ed4sc]

napa is the same, part with hose is $49 and part without hose is $16. They charge a lot for that small hose.

[@joseavina5714]

I have a 2013 ram 1500 5.7 hemi and i cant find the part at all??

[@RAMTRPR]

I have an 09 Ram 1500 5.7 and I located my purge valve (Getting P0456) I don't have a vacuum hose hooked up to the bottom port at all :(. Where is it supposed to go?

[@dopey3995]

Where can I find it in my 2011 Dodge Ram 1500 hemi

[@MotorCityMechanic]

I am showing it being by the battery on that year model. Hope that helps and make sure to subscribe

[@rogerpropst7768]

Will this be good for my 2013?

[@whiskeygrimm]

You rock man, great tutorial, easy to understand.

[@GARZUKII]

I have a 15 ram 2500 w/ a 6.4 in it. I have a couple evap related codes. Truck runs fine with out start up issues or idle issues. It is however difficult to fill up. Different pumps react differently but typically i can fill about .5 gallons to 3 gallons before it shuts off. It seems the fuel doesnt drain into the tank fast enough. Ive pulled rhe handle up and i could see the fuel rise in the neck. When i stop it goes into the tank. Any idea what could cause that?

[@MotorCityMechanic]

Most likely those evap codes you mentioned will play a part in this issue. It could be a tank issue or a vent issue. I recommend having those evap codes checked and tested and then see if any change. If still acting up then the tank may need to be replace due to a sticking valve that cant be replaced separately. Thanks for asking and for watching. Make sure to subscribe

[@f14tomcataocretired95]

MMC, Just wondering, does this apply to a 2017 Ram 1500 5.7 Hemi, Crew Cab?

[@johnvick6855]

It’s not located there on a 2013 Longhorn does anyone know where?

[@Cyberpunk2056]

will this work the same on a 2012 GC with the 5.7

[@AlexRodriguez-rh1ci]

hey bud I have a 2013 ram 1500 5.7 2WD I can't find to location of the part that you replace on the video I wish I can send you a pics or video so you can let me know if is on difrent location

[@dennissecor8092]

Thank you for the video, I have a 2019, is it in the same location?

[@doroteoflores3927]

Did you have to disconnect your battery

[@chichay91]

I have a 2007 4.7 dodge ram 1500. How do I replace the solenoid. Do I need special tools for it? Thanks

[@MotorCityMechanic]

The solenoid is simple enough, it should be located by the bottom of the battery tray on the drivers side. No special tools needed.

[@chichay91]

Thank you, also how do I remove the vacuum lines connected to it.

[@MotorCityMechanic]

@@chichay91 Typically you need to squeeze in on the white part of the end of the vacuum hose to release the lock and then slide it off. Its something hard to describe in words but simple once you understand what I am trying to say.

[@chichay91]

MotorCity Mechanic thank you again

[@MotorCityMechanic]

@@chichay91 Your welcome.

[@garpikemike1]

My 2011 ram with the 5.7 hemi looks different. Can not find location anywhere online.

[@louindorato6855]

Where is the egr valve located on an 09 Ram Hemi 1500 ?

[@Esteban-jy3fq]

I have a question, can a 2016 5.7 hemi engine fit in a 2012 5.7 hemi???

[@skinnypete8702]

Is this located in the same spot on a 2016 Durango with the 5.7?

[@MotorCityMechanic]

It should be on top of the intake.....I believe it will be on the drivers side of the intake. Thanks for asking and for watching. Make sure to subscribe.

[@mayterivera5186]

Would that purge vale cause a check engine to say gas cap

[@MotorCityMechanic]

If the system runs the leak test and it notices that the fuel was just added then it "assumes" it might be a gas cap if the test fails. Any leak can cause this if it runs the test after fill up. I recommend having the system tested first to make sure its sealed and then check the related components. I dont recommend just replacing anything at this point....testing is needed otherwise you might be wasting money. Thanks for asking and make sure to subscribe.

[@mayterivera5186]

I did no leak on cap but computer reads gas cap

[@MotorCityMechanic]

@@mayterivera5186 Its going to take testing the system with a high end scanner that can run the evap tests and possibly hooking up an external tester as well that uses smoke to pinpoint leaks and to test to see if the system is sealed.

[@derekp.1516]

So it’s replaced. How long til the engine light is off? Or does it have to be cleared by a reader?

[@jasoncordill2658]

I just replaced my purge valve in my ‘15 Ram. I’m looking for that answer myself.

[@AriZonaK1DD]

Would this relate to a misfire?

[@wastedyears6653]

Nice job...

[@shaydendeguia1190]

Trucks throwing the 456 and the 457 codes. I changed the solenoid and the cap and that did not fix the problem. I can hear a rattling sound like a pump is running and I noticed the sound comes and goes. I thought it may have been the solenoid. Anyone else hear the rattle and corrected it?

[@JT-yo3xg]

Were would it be located in a 2015 Dodge Charger 392?

[@MotorCityMechanic]

I recommend checking the right side strut tower area....it is just above the right valve cover at the rear.

[@zacharythomas2553]

What are the symptoms you see when this part goes bad??

[@MotorCityMechanic]

Zachary Thomas mainly just a check engine light is noticed. Thanks for asking and make sure to subscribe

[@Iwrestledabeard17]

Mine has a rough idle and small vapor leak detected would this possibly be the issue?

[@lilyhannytheexplorers6164]

I have a 2013 Ram 1500 3.6 liter. I had to jump start my truck because I left the switch on at the drive in, and it killed my battery. After I got jumped started the check engine lit up and It’s showing trouble code U1467. Do you have any idea what that code might be? I’ll appreciate your help.

[@MotorCityMechanic]

Its a shifter related code.....I recommend clearing the code and seeing if it comes back once you have that battery fully charged.

[@lilyhannytheexplorers6164]

MotorCity Mechanic thank you so much for your tip. So, I got battery fully charged and ran it for a couple of blocks and sure it enough it went away. Thank you once again.

[@MotorCityMechanic]

@@lilyhannytheexplorers6164 Your welcome and thanks for the update.

[@jbsanders826]

Will this work for the code P1457 as well???

[@stevemassey4871]

On a 2012 is it in the same place

[@Rene_V7]

I just bought a ram 2013 1500 and the whole valve is missing, including the connectors. Wtf Do you have any ideas why would someone remove that?

[@zacharysipe3501]

Would replacing the Evap purge solenoid make the ticking noise go away?

[@MotorCityMechanic]

Now the EVAP purge solenoid is designed to make a clicking sound when its actuated. Its turned off and on repeatedly and quickly as well so without seeing the vehicle I can only assume that its normal based on the info. Thanks for the question and for watching, Make sure to subscribe

[@zabkan3407]

The ticking noise is from your exhaust manifold bolts being sheared off , every ram got that problem

[@FreakyBeanie]

Zabeh Khanjer my evap valve is making excessive ticking noise (heard even with the hood closed) my manifold bolts were replaced last week. Dealer is replacing the valve out of their pockets for mine as it was a concern before I got the truck from them.

[@zabkan3407]

Steven Richard that's strange, my truck made a ticking noise that I could hear once I start the truck but it goes away once it's warmed up ,does the ticking noise go away after the truck warms up ?

[@FreakyBeanie]

Zabeh Khanjer actually the manifold studs were causing that issue. (ticks when cold until the metal expands then stops) the purge valve only makes sound on mine when the engine is at running temperature and I only hear it at idle.

[@tuckertodd5568]

Awesome, nothing else said.

[@MotorCityMechanic]

Thanks Tucker for watching!

[@LuisAguilar-nu7tj]

what is the part number for this?

[@coreybrowd190]

I have a 2017 5.7 hemi in my ram 1500. And I can’t find my purge evap valve.

[@CUnit1981]

I just popped a P0441 today, could this be culprit? Cleared it and it hasn't come back as of yet... 2013 Ram 1500 5.7. Thanks!

[@MotorCityMechanic]

Thats a possibility but requires further testing such as checking to make sure the EVAP system is sealed and then to see if the purge solenoid is working correctly. I would wait until the code returns then you can either try the purge solenoid or have it tested to see what it might be. Thanks for the question. Make sure to subscribe

[@MarkSmith-hd5uo]

Thank you bud

[@MotorCityMechanic]

Your welcome!

[@robt7548]

Hey motorcity mechanic, great vid. can you give me a direction on my 2003 dodge ram van 1500. stupid thing won't fill with gas, I pulled the 2 fill hoses and blew through both with no obstructions, I removed the line coming out from the top of the tank that goes to the roll over valves and blew through that and no obstructions the air also seems to be going into the tank when I do. I have 0 evap codes all i/M monitor are complete. I'm stumped. also I can't find the support link for your channel is that option only on pc and not mobile? any help is appreciated. happy holidays.

[@MotorCityMechanic]

The most common cause are the fuel tank. The inlet ball can stick. If you try removing all vent hoses and still have issues....then the tank may be needed. As far as support. On the right side of the main channel page there is a support button, you may need to scroll down a bit. Thanks for watching and make sure to subscribe

[@enjoylife7030]

I am chasing this issue on a 2018 Ram 2500 6.4L. New cap, new purge solenoid, and new purge valve under the truck near the tank all replaced. Lights stay on. Truck is just out of warranty at 40,000 miles. I am still searching for possible issues. P0456, P0455 and gas cap light stay on. Losing my mind about now.

[@miltonherron9237]

Did you find the problem?

[@enjoylife7030]

@@miltonherron9237 I no longer have the truck but I did find the problem. One of the vent tubes coming off the tank had been chewed by a rodent. The mechanic at the dealer was able to splice in a new section without completely replacing the whole tube. Problem was fixed after eliminating that leak in the system.

[@NO-ve8jb]

I know this video was posted a while back but will that evap purge solenoid be the same on/or in the same location on my 2012 ram

[@MotorCityMechanic]

+N LeGresley The location on your vehicle is just below the battery. I appreciate the question. Make sure to subscribe

[@NO-ve8jb]

Thanks a lot!

[@MotorCityMechanic]

N LeGresley Your welcome

[@Xedus00]

Hello, I also have a 2014 ram 1500 with this issue and was looking to buy the solenoid online but cant seem to find the right part. By chance do you have the part#?

[@MotorCityMechanic]

Here is a link to the part that I found online: www.factorychryslerparts.com/products/DODGE/RAM-1500/VALVE-Purge-Control-ESG--ESG--ESH--EZC--EZH--EZD--EZH--Valve-Only/10662543/04627694AA.html . Make sure to call your local Dodge dealer and have them verify to be sure using your VIN #. Hope this helps. Make sure to subscribe

[@juansaldivar85]

What's the part number on that item you just replaced?

[@MotorCityMechanic]

I dont have access to that info. It also changes from year to year. I recommend calling your local dealer and give them your VIN number and have them look it up. That way you are 100% sure what it is.

[@juansaldivar85]

@@MotorCityMechanic Thank you David My dodge doesn't have that canister purge valve there can you help me locate it please? I'm getting a code P0456 My Dodge ram is a 2013 1500 sport 5.7 hemi with 86k miles.

[@MotorCityMechanic]

@@juansaldivar85 The service info shows it being in the same position on the 2013 Hemi....next to the throttle body. Now as far as that code....small evap leak, there alot of possible causes. It requires using a EVAP smoke machine to check the system out to locate and leaks if there are any. Otherwise it would just be a guess.

[@rexluthor71]

I have a 2010 dodge ram 1500 and found the solenoid under the battery box. But here's the rub. There is a line going to the throttle body and a electric connector but that's all. Isn't there supposed to be a line that goes out the bottom to the gas tank? Please advise

[@MotorCityMechanic]

The purge solenoid in the service info shows one line directly out the bottom on the purge solenoid and one out the side. There should be 2. One leads to the engine and the other to the canistor underneath the vehicle.

[@rexluthor71]

Found the problem. Tyvm for the assist. The mechanic that did the exhaust manifold bolts disconnected the line and never put it back on. I found it jammed up under the fender behind the battery.

[@MotorCityMechanic]

+rexluthor71 glad you found the issue. I appreciate the update. It was just one of those things that didn't show up for a few days after the repair instead of right way.

[@Durango214]

I just changed it But my check engine light is still on do I have to run the vehicle

[@marcel4334]

Me too, did yours turn off

[@mexicanoloco4327]

thank you sir

[@MotorCityMechanic]

Your welcome and thank you as well. Make sure to subscribe.

[@doorchamp]

Where is it located on the 2013?

[@MotorCityMechanic]

If its a 5.7 hemi and a 2013 then exactly the same place as in the video.

[@doorchamp]

it is a hemi but not located in the same spot. I cant find it. lol

[@MotorCityMechanic]

If its a Ram truck and a Hemi....thats what the service info states. guess I need to check out the next 2013 that comes in. The previous versions had it located on the drivers side near the fuse box and close to the frame.

[@doorchamp]

That would be great, thank you!

[@esmeraldagonzalez787]

Hi did u ever find out were its located for a 2013 ram hemi 5.7

[@carlswanson8948]

My ram starts then stalls also the battery dies when its not running

[@brandoncorreia3758]

can you tell me where the evap solenoid is located on a 2014 ram 3500 with the 6.7

[@MotorCityMechanic]

+Brandon Correia Evening Brandon.....the diesel 6.7 doesnt use/have an EVAP system. It only applies to has engines

[@brandoncorreia3758]

MotorCity Mechanic

[@brandoncorreia3758]

MotorCity Mechanic lol thanks for the reply. I was pretty sure it wasn't on the diesel. but that was what I was told the code was saying. would a dirty fuel filter and separator cause the EVIC to read "fuel system issue see dealer"?

[@MotorCityMechanic]

Fuel filters that are due by the onboard computer monitor will set a message on the display saying......service fuel system. Just like you will get the oil change message at different intervals. Same basic operation. So if thats the message your getting then replace both fuel filters and reset the message. If the message is different then I recommend having the codes checked to make sure no other issues.

[@brandoncorreia3758]

OK great. The for the info I really appreciate it.

[@jimmywarden6320]

Wheres it at on a 12 big horn

[@rockgirard9903]

Need better lighting and less background noise.

[@MotorCityMechanic]

This video is 8 years old…..I have progressed lol. Check out my newer videos and you will see a pick jump in quality

[@user-jm9ep3zp5g]

what code did you have ?

[@ednasalazar7677]

my ram doesnt have that infront..... where could it be cant find it

[@MotorCityMechanic]

What is the year and the engine size?

[@mlaugh3]

Very good channel. Code P0456. I need to do this to my 2014 Ram 3.6 v6. Where is located on the v6 Ram?? Thanks!

[@MotorCityMechanic]

On that engine it will be in the passenger side of the upper intake. Thanks for watching and make sure to subscribe.

[@mlaugh3]

ok I will look again.......................................................