Just installed 12" Spearheads on my '22 RGS. Thanks for the video. Finished in under 2 hours. Great bars, love 'em.
@bigfresh76962 жыл бұрын
Just ordered these for my 22 RGS and they will be coming soon. 2 questions for you. Did the handlebar turn signal controls go back on okay? People who did the 21 RGS said that you have to buy half clamps to make them fit. Also, I read that the clutch side handlebar is glued on is that correct? And if so how did you get it off?
@robertrodriguez90502 жыл бұрын
@@bigfresh7696 trying to remember but I think I had to snip off the pin from the controls clamps since these bars don't have holes for the pins. I installed new grips too when I added these bars so the clutch side is still on the stock bars. 🙂
@thatsfunny1231 Жыл бұрын
Are all the cables long enough? He said 2015 to 2019 was but I have a newer one and just want to make sure.
@gerrycorrigan80035 жыл бұрын
The 12 inch Spearheads are great. The video was very helpful for the install on a 2019 Roadglide. Throttle side was a challenge getting around the corner. You need to be aware that if you do not pull the main fuse you will get an ECM error code when you start the bike.
@jaimebedolla9898 ай бұрын
I wish I read you comments prior to installing, now I have a check engine light on , mine have heated grips as well . Any advice how to self clear please ? I’ve already tried pulling fuse and restating and same .
@NKBobcat4 ай бұрын
Your video sold me on the KT's Going to put a set of 14" bars exactly like those on my 2024 Road Glide 3. Thank you!
@dirtrider65725 жыл бұрын
Just want to give a shout out them bars are the bomb,,,, I ordered them on Monday receive them on Thursday and put them on the same day easy bars to put on they look amazing..
@specialistonfire6 ай бұрын
Thank you for the awesome video, installing my 14” spear heads this evening on my 15 RGS, just as soon as FedEx gets here with them. Rain shut them down yesterday or they’d already be on
@jerrylinton12 жыл бұрын
I just watched this with no sound and i understood everything that happened and why you did it. Quality of video was choice and camera angles too. Thanks for this
@tbyrd33414 жыл бұрын
Great bars...installed same day received. Video is dead on. Installed 14 on 2015 roadglide special. Would like to point out. My bars didn't have kst logo engraved on top. Kst Logo badge was located on throttle side. When pulling cables be sure to lose up the rubber clamps holding cables. This was the only way my stock lines worked with no problem. Does takes some elbow grease to get the throttle side bar in but, once on bike the adjustments are easy. Great overall and quality. Hope this helps. Follow the video with these tips and your golden. Took me about 1 hr because I did all the prep work before receiving my bars. Took 4 days to receive them. Overall would guess 2-3 hrs. Hope this helps.
@ericv79flh5 жыл бұрын
You made that look easy.
@leerhill4 жыл бұрын
Thanks for this video it made the installation of your bars a breeze
@ohiobellboy5 жыл бұрын
Gotta have a set for my '15 CVO with the smaller clamps. Love the ease of installation on your video and the adjustability.
@bradleylynn5112 жыл бұрын
Just installed 12inch straight jackets. 21 RGS. Took like than 2 hours. That was in a parking looking with a Walmart set of tools. And I hand filled the perch clamps with some older welding tools. Very happy so far! Thanks KST.
@gregrapattoni83235 жыл бұрын
Thanks for the install video. Just bought a pair and going to install soon. 2018 Road Glide Special
@40mustng2 жыл бұрын
Excellent video on step by step installation. Well done
@oldfireguy572 жыл бұрын
I had ordered 12" Paul Yaffe monkey bars and they sent 10" instead so now I have to wait 2 more weeks for the replacement but got to looking around and found these, I'm impressed enough that I went ahead and ordered 14 Pioneers for my 19 RG ultra and I'll just sell the PY's locally. Looks way easier to install and lots more adjustment in the way of hand positions.
@markbeckett34604 жыл бұрын
Great video. Installed mine today on a 19 roadglide. Love the bars rides like a whole different bike.
@chairfitcamp2 жыл бұрын
Great video. What do you guys charge to install?
@2000smiley15 жыл бұрын
There is another video from a different company on youtube for a 2015 RG that shows a big plug that you have to unpin to remove the throttle by wire. I guess on the 2015 the plug was different (much larger) than the 2018/19. Just a bit of info that I noticed.
@heybruh32742 жыл бұрын
Re: 2016 FLTRU It's really as easy as shown here. Buy these bars. Quality product. My arms and hands are finally where they should be. I had zero issues with the install and this was my first time ever changing bars. As always, follow good maintenance protocols as outlined in the service manual.
@spencerburk99554 жыл бұрын
Love my spare head bars. Went with 14” and love them on my road glide.
@abdallahmoussa1983 Жыл бұрын
How tall r u?
@jdisgood002 жыл бұрын
Left some key steps out. Especially on the hydraulic lines. But the video was helpful.
@andyreeves11464 жыл бұрын
Just completed install of 14 inch straight jackets on 2020 Road Glide. Brake and clutch lines a little too tight so needed to pop both out of the rubber block on the right side of the upper frame. Other than that super simple and look awesome
@danielE8102 Жыл бұрын
Outstanding Video
@kstkustoms1324 Жыл бұрын
Thanks daniel
@CherylGuidry-r3k Жыл бұрын
Thank you! Very helpful!
@DONALD-MAGA4 жыл бұрын
I installed these bars on my Road Glide today and it was a PITA. The electrical lines are long enough and not a problem. The hydraulic lines are just barely long enough with no slack at all. I had to run the hydraulic lines a different way than showed in the video because the gauges would not go back on. He does not tell you how to take off the trip meter button, which is another PITA. The factory service manual does not help at all, I had to find a different video on You Tube to get the button off. And finally, the stock left hand grip is glued on and is another PITA to get off. If I had been warned about the grip I would have bought new grips before attempting this install. A big negative with these bars for me is the fact you can't push the bars forward enough. I have long arms and with the design of this three piece bar, it stops when it hits the top of the forks limiting the amount you can push them forward. The bars look good but knowing what I know now I would have picked a one piece bar instead. Update!! The hydraulic lines are anchored to a plastic block on the right side of the frame. On a Road Glide turn your bars all the way to the right and look down inside the inner fairing on the right side. You can see the block on the frame holding the lines. The block is easy to pop out and take the brake and clutch lines out of it. Leave the other two in it and pop the block back in place. This will give you plenty of slack for 14" bars. I don't know why KST doesn't tell us about this. I had to watch a Factory 47 video to find out how to do it. Starting at 1:45 in the video below they show you how to get the slack you need. Thanks for nothing KST!! kzbin.info/www/bejne/mGbRg6eeo8Rgp5o
@marcnunes69165 жыл бұрын
That’s what quality products look like 👊. How do you make sure both side are mounted even? Does the base have turn marks on them like a dirt bike?
@TheBlueBikeDoyle4 жыл бұрын
Didnt know yall had a you tube channel. Here I was thank I should ride over and do video about y'all I'm just in Tallapoosa.
@2wheelobsessed4 жыл бұрын
Lots of very helpful info in this vid, great job 👍🏻
@kmactv38703 жыл бұрын
Can you make a video on the 14-20 road king special for the road king riders? 😎. Seem like we would have way less work to do without the fairing and Also show how the riser works and how much we can tilt it
@yohangerman2332 ай бұрын
The perch clamp works without having to shave down the pin on the inside?
@chrisoconnor9021 Жыл бұрын
just put on kst spearhead 14' bars.wire extensions and a badass bagger 4'clutch extension perfect combo makes install simple!
@steikio13 жыл бұрын
2021 HD Road Glide special: just installed the 12" spearheads 1.5 on my bike. Install was straight forward. NOTE: I really struggled with having enough slack on the clutch cable to properly seat the housing on the handlebar. As you know HD went to cable cluches in 2021 for their touring models. The clutch cable is super stiff, tight and I had no addition slack. Bottom line is that I made it fit, but it is tight. Really tight. I would probably have purchased a new cable either plus one or plus two. I did route the cable just the way it came stock. The switch housing and fly by wire cables were long enough, so that was good. I sat there trying to figure out out an alternative way to route the cable, but I don't think it's possible. I also loosened the the plastic clamps that run along side the frame to give me a little more slack. Please share your stories.
@stfuliberal3 жыл бұрын
Really, I thought OEM was 12", thanks for the heads up. 2021 Roadglide limited.
@pnwrgs21752 жыл бұрын
Literally running into this problem right now on my 21 RGS. Time to see hard it is to change a clutch cable
@steikio12 жыл бұрын
@@pnwrgs2175 Its going to be a tight fit for the cable. But who knows if every road glide is made exactly the same.
@pnwrgs21752 жыл бұрын
@@steikio1 ended up getting it to work. I just had to take the clutch cable out of the housing and reroute it.
@jeremyaurand2582 жыл бұрын
Try rerouting the clutch cable outside of the cluster it'll give you a lot more room
@SCFoster4 жыл бұрын
Have an install feedback regarding the right brake line for a 2020 Road Glide Special FLTRXS. Purchased the 14” rise Black Spearhead handlebar set. Watched this install video and made sure the brake lines were on top of the bar/clamp (15:00 in the video). However, the brake lines were still too tight to fit the speedo/tach enclosure. After a LOT of fiddling around, I noticed there is a plastic block on the right (throttle) side of the steering head that holds four hydraulic lines. Popped that out of the holder and did get more play in both left and right (clutch & brake) lines. Still not enough to be comfortable. Then popped the two hydraulic lines (clutch and front brake) out of the block, keeping the other two there and put the block back in the holder. Found a tie-wrap holding one of the lines to an electrical connector near the block and cut that. Substantially more play now with no binding at full lock left and right. One other note, at 17:50 in this video it’s recommended to torque the riser clamp bolts to 30 ft.lbs. Checking the shop manual, Harley recommends 16-20 ft.lbs. Nice quality product.
@RoadGlideSTShenanigans4 жыл бұрын
Awesome bro! Thank you for that! Getting ready to do the same install on my 2020 Road Glide Special.
@DONALD-MAGA3 жыл бұрын
The reason you have to increase the torque on the clamp is because you eliminate the pin which keeps the stock bars from moving. Even increasing the torque to 30 ft.lbs. the Spearhead bars will still move if you pull back too hard. This happened to me on a trip last year and had to wait until I returned home to torque it down again. I am looking for an aftermarket clamp that will hold the bar more securely. Any recommendations?
@anthonychinea67225 жыл бұрын
Thank you brother it helped me 100% 😎
@Sforce685 жыл бұрын
I believe the lever clamp screws are T27, and the switch housing screws are T25.
@cjsmith5 жыл бұрын
Nice looking bars with a great design
@BigHeadPatReviews3 жыл бұрын
Can we do a video on a Road King. I bought the Renegades 14’ and I was told we wouldn’t need any extensions.
@edblack55343 жыл бұрын
Enjoyed the video and thanks for the help! I kept getting distracted by your watch. What is it?
@DONALD-MAGA3 жыл бұрын
If you are having trouble getting enough slack (which everybody is) in the front brake and clutch, this will fix that. The hydraulic lines are anchored to a plastic block on the right side of the frame. On a Road Glide turn your bars all the way to the right and look down inside the inner fairing on the right side. You can see the block on the frame holding the lines. The block is easy to pop out and take the brake and clutch lines out of it. Leave the other two in it and pop the block back in place. This will give you plenty of slack for 14" bars. I don't know why KST doesn't tell us about this. I had to watch a Factory 47 video to find out how to do it. Starting at 1:45 in the video below they show you how to get the slack you need. Thanks for nothing KST!! kzbin.info/www/bejne/mGbRg6eeo8Rgp5o
@MrPhipsi742 жыл бұрын
If you have heated grips, can you remove the throttle grip and sleeve together and reinstall them together, or do you have to remove the grip from the sleeve? I want to avoid dealing with the heated grip connector on between the throttle sleeve and the grip. When I installed the heated grips, I noticed that connector seemed very delicate.
@davidmatias62392 жыл бұрын
I have a ECM- BCM U0142 code that won’t clear .. I checked all connectors x3 and even unplug the battery . Right turn no signal or or any power for the bike to turn on .. any advice? 😩 b4 I cry
@kencharron62182 жыл бұрын
I've got same issue David. Install went well but now I've got nothing in my digital odometer. No codes, light, neutral indicator...nothing but radio comes on. Did you ever find a solution to your no power issue?
@davidmatias62392 жыл бұрын
@@kencharron6218 yes, I pinched the wire controls that on my throttle side . I replaced it with a new one for $26 bucks . It sucked that I had to remove the bars and re wire that side but I may least I was able to fix it myself
@jaimebedolla9898 ай бұрын
I have a check engine light on after installing my 12’s with heated grips , any suggestion how to clear light ?
@cgasu03115 ай бұрын
I have a 2022 Road Glide Limited, it has heated grips is this a separate wire to pull?
@kstkustoms13245 ай бұрын
Yes watch my internal wiring video for 14-23 models (separate video). It shows how to do it there
@jaimebedolla9898 ай бұрын
Installed 12” Spearheads on 23 RG and throttle and brake cables very tight , but plenty of slack with wires after following his steps , my problem is Speedo cluster is very tight and unable to insert ignition beauty ring and also have check engine light ON , any advise how to fix please ???😩
@CVOROADGLIDEDUDE835 жыл бұрын
I just installed the 12 inch on my 2019 CVO Road Glide, install was very easy. I love the way you can adjust these handle bars exactly how you want them!! Only complaint is the green mesh use to pulled the wiring through needs to be longer. KST, you get a A plus!
@jwill17825 жыл бұрын
Devil DOGG83 I order done to install I’m 2018 RGCVO. Did all the cables and wires fit?
@CVOROADGLIDEDUDE835 жыл бұрын
@@jwill1782 All the cables fit perfectly, you will have to cut a few zip ties that are holding the cables in place.
@jwill17825 жыл бұрын
Devil DOGG83 thanks for the reply I forgot to add mine are 14” will that still fit?
@stephanieclark35784 жыл бұрын
Will the cables need to be extended with 14” bars on a 2019 road glide ultra?
@earlliotti53163 жыл бұрын
For comparison, how tall are you? Looks like ur arms would be where I want mine. Thanks, great vid!
@johnford37617 ай бұрын
Going to 14” bars do you recommend replacing the riser bushings?
@kstkustoms13247 ай бұрын
Kind of personal preference. It doesn’t hurt, but leaving them stock isn’t going to hurt anything either
@chadepperson56093 жыл бұрын
FYI, for those of you that plan on purchasing these bars. The amount you can push the bars forward are limited by the screw holes for the gages. To far forward and you can't get the screws back in the holes. Also, pull the main fuse or you get a check engine light. You also need to remove the odometer switch button, which he says nothing about
@jaimebedolla9898 ай бұрын
I didn’t know about the fuse prior to installing and have check engine light on , any advice on how to remove light ? I tried unplugging fuse and then restarting and still same .
@rbljacksonАй бұрын
I bought a 2019 Road Glide Special that has a set of the KST Pioneer bars already installed. How hard would it be add a set of heated grips to this set up? Can it be done without removing everything?
@kstkustoms1324Ай бұрын
@@rbljackson yes watch the internal wiring video for 14-23 models. It’ll be the exact same process
@jeremyaurand2582 жыл бұрын
2021 road glide limited requires new half clamps for the control mount.
@Concreteguy944 жыл бұрын
no need to install poly bushings for bars that tall?
@sotaboythrill23 жыл бұрын
Mine arrived today! What’s your estimated time of installing?
@louisgiardina89182 жыл бұрын
Question if you have the 12 in instead of the 14 in do you still need to take the bracket out that holds the wires in the gauge cluster he said by removing you can gain 2-3 in if you have the 12 in you are technically 2 in shorter then the 14 in was just wondering?
@jasonblue2834 жыл бұрын
How do you run the wires through the Renegade bars? Seems nearly impossible to get around the bend in the top. I’ve been trying to pull the wires through with fishing line, but plugs won’t make that bend.
@jidoebaltimore1883 жыл бұрын
If the pins lock the bars and controls in place. They must be necessary in the long run . Just my observation
@billclemmons4946 Жыл бұрын
I've ordered the 12 inch Spearheads and am considering installing them myself on my '22 Road Glide Limited. Does the fact that I have heated grips raise any unusual issues?
@kstkustoms1324 Жыл бұрын
No sir. Check out my internal wiring video for 14-23 models. I go over the heated grips in it. You could also do the locked and loaded or fully pre wired options. Check them out on the site
@jblack75554 жыл бұрын
Just got my 12 inch pathfinder today..Do I need to pull the wire connector ends apart b4 placing wires in provided mesh?
@RougeWhiteBoy Жыл бұрын
so am i right in saying that you can go to 14" hangers without changing anything? thanks for the video bud! ive got a 2016 glide
@kstkustoms1324 Жыл бұрын
yes sir
@kencharron62182 жыл бұрын
I did everything by the video. All went well until I tried to start the bike. No ignition, no controls worked, only got radio. WTF happened? Everything went so smooth.
@travismiles8635 Жыл бұрын
In the middle of the swap. Made a few minor mistakes, mainly clamping bars on too early. But I'm confused about how the clutch and brake lines run. I see overtop the riser ( I messed that up rushing). But do they run behind the cluster. Someone help me lol
@firedoc30142 жыл бұрын
Will your bars work with the oem harley heated grips?
@mikephillips65744 жыл бұрын
Just finished installing 12” on a 2012 RGS. Got done, no power. Radio works, no power on ignition. About to take apart, any suggestions on what to look for, which connection?
@benjones46584 жыл бұрын
Is the installation the same for for a 2019 Road Glide Ultra? Curious if the cables and wires will work or have to be extended with 14” bars? Any help much appreciated.
@Roadglide862 жыл бұрын
This seems easy, I was quoted $750 just for the replacement, bars not included in that price
@HPG454 жыл бұрын
I don’t have crap for clutch/brake line slack; installing 14” Pathfinders. I noticed in the video after the brake/clutch were mounted, that the lines now ran outside the cable housing (where the speedo/tach go into). Any suggestions? Thanks
@koolkustom5 жыл бұрын
I’d like to see an installation video of the Pioneer bars.
@RideAmerica4 жыл бұрын
I just installed the pioneer bars. Short answer, I love them. Longer answer ... What they don't show in the video is the PIA process of routing the clutch and brake line in a crazy small spot on the side of the gauge cluster. After communication with them they emailed back some additional tips to gain more cable length and suggested taking off the protective sheathing. When all was said and done, I felt it better to dremel out a C shape spot for the cables to pass through the gauge cluster. I did this right below the screws that hold the gauge cluster. Looks like it was almost from the factory but not what I had intended after buying $400 bars putting them on a 30K bike. I feel there is a small design flaw and when I did route the cables where they suggested - it was just too harsh of an angle and too tight a fit. I did not feel like comfortable that and hence the dremel. Ultimately it turned out great and the 3 piece bars made internal wiring a breeze. Or at least on the 12" bards I had ... 14" may have been more challenging. The provided mesh was a huge help. Great guys and fast communication and very nice product and love the adjust-ability but in my opinion, you have to get a little created with running the brake and clutch lines to suit your comfort.
@steikio13 жыл бұрын
@@RideAmerica check out my comment
@rottwaller072 күн бұрын
Every thing installed correctly I got to reconnect gauges cluster and nothing comes on. Bikes turns on and everything. But none of the gauges light up and the screen doesn’t turn. Do you think I blew a fuse.
@kstkustoms132419 сағат бұрын
@@rottwaller07 check the fuses. 5amp battery most likely. If it’s not that check the pins on the backside of the gauge cluster
@rottwaller0711 сағат бұрын
@@kstkustoms1324 yea it was the fuse cause I had the switch harness on the clutch side pinched smh just ordered another set from yall . I gots to be more careful
@wesleydean13582 жыл бұрын
How does the dealer justify 7 hrs to do this? Hwy Robbery
@bigpunisher30754 жыл бұрын
I might just be dumb damn.. still haven't figured out how to take the throttle by wire out. Any advice?
@davidchamberlin92732 жыл бұрын
Just purchased a 2022 cvo RG do you know if you can use the stock cables and wires without extentions with the 14" spearhead ? Love these bars. Thank you
@devonhundley98552 жыл бұрын
Just installed 14” on a ‘22 road glide special. Called kst and he informed me that on ’21 & ‘22 road glides you will need a 4” clutch extension. Video title is a little misleading.
@davidchamberlin92732 жыл бұрын
@@devonhundley9855 hey how you doing yeah I misread your reply so I just deleted mine LOL I ordered the extension just so I had it just in case it does save from Cut and zip ties removing clamps trying to fish that cable to get enough slack so much simpler just to replace the stock clutch adjustment piece and put that extension on there as for the wiring I ordered wiring and was nothing like everybody said I had enough wire there I never even had to remove the plugs from that plate behind the speedometer where they're attached like people are saying to do everything was really long enough I think I only used a few of the extension and wires and the rest I just put away but they are great bars man they really look good took a couple rides to get them tweaked where I like them but ride safe and enjoy brother
@breezetelemaster13683 жыл бұрын
Thank You!
@tomwagaman64402 жыл бұрын
Do these fit a 2022 RGS, 12" without having to extend any wires or lines?
@Davan5144 жыл бұрын
Give it a try with heated grips. It is not so simple.
@corrieb44644 ай бұрын
Thanks!
@kstkustoms13244 ай бұрын
Thank you!
@robertkealoha82552 жыл бұрын
Do you also have those handlebars and 10 and 12 in
@jwill17825 жыл бұрын
KST just installed these on 2018 Road Glide CVO. Spearhead in 14” my hydro lines are tight on both sides and suggestions
@m.z.17304 жыл бұрын
Mine are too. What did you end up doing?
@DONALD-MAGA3 жыл бұрын
@@m.z.1730 The hydraulic lines are anchored to a plastic block on the right side of the neck. On a Road Glide turn your bars all the way to the right and look down inside the inner fairing on the right side. You can see the block on the frame holding the lines. The block is easy to pop out and take the brake and clutch lines out of it. Leave the other two in it and pop it back in place. This will give you plenty of slack for 14" bars. I don't know why KST doesn't tell us about this. I had to watch a Factory 47 video to find out how to do it.
@senfar5573 жыл бұрын
Rodgide special 2020 will not have enough length for hydraulic lines for a 14 inch bar. Too short. I tried it it does not work
@specialistonfire6 ай бұрын
How about my anti slip insert isn’t on the bars I just got off the FedEx truck, no stamped kst logo on the right side like the the set in the video 🤦🏻
@kstkustoms13246 ай бұрын
We went to a traditional knurled surface and a more decorative emblem on the right side.
@johnnyceeuontheroad.23894 жыл бұрын
Have 2018 SG FLHX, can I install these 14" bars without brake and clutch and wire's?
@edgay94462 жыл бұрын
I sold great video
@loosewheel754 жыл бұрын
Thx 😊 video really helped
@texasspeed21422 жыл бұрын
Would the installation be the same on a 21 road glide?
@terrencepeeples91175 жыл бұрын
Do u HAVE to move the tray? Seems like tray would keep things neater and bouncing around less.
@kstkustoms13244 жыл бұрын
You can get the wire extensions and avoid that step
@plast733 жыл бұрын
Hi, what is the highest possible steering handlebar I can put without changing the wires? RG 16
@jordankovacs1624 жыл бұрын
I got mine installed but one of the throttle cable sensors wont reattach and my check engine light is on because of so. any ideas what might work ?
@DoubleH19065 жыл бұрын
Those are some sweet bars. At 6'2", which height would you recommend? Have slight should problem also with torn rotator. I have a 2019 RGS
@kstkustoms13245 жыл бұрын
I would suggest the 14"
@DoubleH19065 жыл бұрын
@@kstkustoms1324 Appreciate that man
@claytonbjornson4 жыл бұрын
I had 18 in on my 2015 Road Glide Special and absolutely loved them.. Just picked up a 2020 Road Glide CVO I'm putting 20 in bars on ... Im 6'6" so i personally think 14 are to low for you..
@specialistonfire6 ай бұрын
What size clamp do I need for a 2015 road glide special? I see there’s two different sizes
@kstkustoms13246 ай бұрын
1.25”
@jonbassett80234 жыл бұрын
i have a 2019 R K Special. My guy is installing these bars and having a problem with exposed wiring at the base. He says there will be 6 to 10" exposed wiring after install!? How do you hide the wiring when installing on a Special!? When I ordered these from J&P it said these WILL FIT my 2019 Road King Special...HELP ASAP PLS!
@rodneyhanbaum6974 жыл бұрын
Just changed my bars on my 2018 Road Glide, now my check engine light is on? How do you reset be it?
@duanepeterson37294 жыл бұрын
Just did mine today and my check engine light is on in my 2017 road glide special
@jaimebedolla9898 ай бұрын
How did you guys fix please ? Same issue
@nickhinsen83895 жыл бұрын
Damn, I must be special, I didnt get any mesh for pulling my wires through, absolute nightmare trying to install these without
@weesejustin14 жыл бұрын
Ummmm yea me either it’s a bitch
@kstkustoms13244 жыл бұрын
What bars did you buy? Our one piece bars do not come with the mesh sleeve. It is not as effective on the one piece bars as it is on the vanguard series
@weesejustin14 жыл бұрын
16” renegades
@newmoney81283 ай бұрын
So do the wires hang out the bottom and then reconnect or down the bottom and through the curve like they are on the Harley factory?
@kstkustoms13243 ай бұрын
just straight out the bottom of the tube. everything tucks over at the gauge cluster, you cannot see the wires
@newmoney81283 ай бұрын
@@kstkustoms1324 So can I still adjust the bars inward or outward if I needed to with the cables hanging down
@kstkustoms13243 ай бұрын
@@newmoney8128 thanks correct. They are still fully adjustable
@newmoney81283 ай бұрын
@@kstkustoms1324 well you guys just gained a customer
@newmoney81282 ай бұрын
@@kstkustoms1324 when I order the handlebars Will it come with the sleeve that you use to route the wires through?
@kclarkeadventures3 жыл бұрын
Is there a trick to get same angle on pull back on bars?
@andymedinasr.92248 ай бұрын
This won't work for a 2023 RG because they switched to a cable clutch and I'm pretty sure you need extend it.
@kstkustoms13248 ай бұрын
You can go up to a 12” with stock components on the 21-23 models
@jaimebedolla9898 ай бұрын
Yes they will work but brake line and clutch line tight as hell even with cutting zip ties . Also having issue with Speedo cluster going back in tight and can’t place the ignition beauty cover back on any advise ?
@kstkustoms13248 ай бұрын
@@jaimebedolla989 watch my video showing how to route the clutch cable. It’s a short one. Also remove the brake and clutch lines from the hose tray on the right side of the neck
@andymedinasr.92248 ай бұрын
Try turning the steering wheel@@jaimebedolla989
@Desmo14 жыл бұрын
Clearly this dude is leaving out important info regarding using stock lines with a 14" bar. I just installed (12's) on my RGS and I definitely had to cut the zip ties as well as removing the lines from the bracket holding them in place under the fairing. He makes it look easy with 14's but I assure you that even with 12's and cutting ties it's going to be a tight fit.
@tbyrd33414 жыл бұрын
Ordered and received quickly. Video died on. Installed 14 on 2015 RD Special. Stock cable where tight at 1st but, it eventually becomes easier with some more pulling and taken cables out of seated rubber clamps. Throttle side bar take some elbow grease to get in but, once in your good to adjust. Also fyi my bars had the kst badge logo on the side and not engraved on top right . Hope this helps. Great bars overall.
@newmoney81282 ай бұрын
@@tbyrd3341are the bars straight out of slanted inward like Harley's bars
@tank73585 жыл бұрын
Do you have to remove the wires from the tray if you are only installing 12inch renegade bars.???
@kstkustoms13244 жыл бұрын
You do not have to
@Mikesfishing5 жыл бұрын
Was on your website, i really like these bars. When will these be available?
@chanceedwards18865 жыл бұрын
Website says available to order March 18th
@donnguyen6983 жыл бұрын
Do these handlebars work for 2020 Harley Road Glide CVO? Please let me know!
@sotaboythrill23 жыл бұрын
Email customer service! Responded quick to me and I just received the 12” today for my RG Special
@domzarate37964 жыл бұрын
How do I get those bags and gas tank protection?
@陳志強-h2o5 жыл бұрын
How should i choose the length of the clamp for My 16 FLTRXS ?
@MalcolmTodd19665 жыл бұрын
My new handlebars!
@nikkivuagniaux31804 жыл бұрын
The dealer tells me it’s a 4-5 hour install...so about $340 - $425 labor. Does that seem right?
@jordankovacs1624 жыл бұрын
with no experience like me it took me and my dad 2 and a half hours to install