2017 Can Am Outlander Warn Winch goes out but not in

[@odayfamilyandfriendsoutdoo3731]

Great video. I just purchased a used 2017 with them exact symptoms and im headed out to the garage to clean them grounds!

[@TheDp1965]

Thank you for this video. My Warn winch on my Can Am 850xt was not coiling up. Popped off the panel to find all the nuts on the silenoid where not tight. Gave them all a good tightening and fixed the problem. Would of never check this without your video. Cheers.

[@savannahskiis8378]

Thanks much for the video! Was on a wild goose chase trying to find a new contractor (snow coming in tonight) and nobody within 150 miles had one in stock. Watched your video and got the metal to metal contact you suggested. Works perfectly (like a winch that has been used less than 5 times should)! Saved me bucks!! Thanks again!

[@savannahskiis8378]

thats contanctor not contractor...darn spell check.

[@savannahskiis8378]

shouldn't drink the egg nog so early in the day.......contactor!!!!

[@mainenorthwoodshunter3265]

Ugh! I have a 2018 North Edition 650 can-am. We were told the selenoid was under the seat. we found it and took it out with a lot of work. After watching your video it looks like we may have taken the wrong thing out. I didn't realize there is a solenoid for the winch itself as well. I am having the same problems it has been going down but not up then suddenly it did the opposite it went up but now won't go down. I will have to see if I too have the selenoid behind my fender and check the connections before I purchase anything else. Thank you for your video. I wish I had watched it before I took out the selenoid under the battery tray.

[@olegk455]

Came here to see where the damn thing is located as I am installing a wireless remote from Warn but it’s good to know about this possible issue.

[@tylerpoan6104]

I took the box apart and it was carotid on the inside so I took sandpaper and cleaned it up works good now.

[@davesmith5425]

I have a 2016 can am 650 XT and have the same problem. It happened the first time I used my plough.

[@mrlariata9290]

Thank you for posting this video fast forward to today February 2020. I have a 2019 can am Outlander Max 650 with a warn winch and my machine has 200 miles on it.Just had my plow installed and used it for 10 minutes and cannot lift the blade alls I got was clicking. I'm gonna go out there and clean up my connectors the ground remove the paint like you said in this video and see how it goes thank you very much.

[@codytoal2598]

How did that work out for you? I’ve got a warm winch making that clicking sound as well.

[@simshot4]

Outlander 570 '16 , plow was going down but not up . Dealer told me to change solenoid , they often burn they said . Took the solenoid out , tore it to pieces and found severe damage to pieces that click together . Took sandpaper and cleaned everything up , sanded the 3 bracket holes and the 3 holes on the solenoid and everythings ok for now . The inside pieces are cheap metal , it will stop working someday cause of that . Saved 100$ today , may want to find spare winch kit for next time

[@robnoxious8482]

Thanks! You're awesome! First like 👍 in a long time!

[@hydro_rebel7741]

I have a '22 outlander, my winch is the opposite will go in with the button but when I hit the out button it does nothing. I used the winch one time and couldn't even get it to free spool. I finally got it to free spool, looked inside and it's all rusty and sounds like the bearings are bad. I've only had the machine for about a month.

[@COLTAR45]

Nice video, but was the second (new) solenoid also displaying the same problem? If not, then it could be the new solenoid fixed it? Cheers

[@kyleames370]

I have a winch on my Can-Am outlander brand new I was hauling some trees with it and it will not go in but I can pull it freely wondering if you knew anything about that

[@ari110]

I think I have that problem also and now I know what to do.I’ll forgive for long video😁👍

[@Chris-ut9fc]

Thanks

[@jerrygreen1277]

My 2010 Outlander max 800 only does this after using it alot plowing snow. Let it sit 10 min, then it starts working again.

[@CK-dt6nx]

I found the problem on mine. I took apart the solenoid (top half) and found that the points between the positive and post going to the winch were melted from arcing. Turns out cheap or crap metal for the amps used by the winch using a plow. I sanded the worn face down and started working again...at least until the face melts again. Job is real easy to do. Theres a cover for the top half, 2 screws, rubber O rings holding the posts in place just dont lose those when you pull the posts out. The point plate that moves and and down, twist sideways to pull apart and put back in. Look at the face of the plate that makes contact with the posts and sand the worn parts.

[@CampingDad247]

mine goes out and wont go in but i can hear the silinoid click when pressing in prob winch wire corroded?

[@linz9990]

I'm here for the same issue - how did u fix it! (Hope u get this msg) ~~ also how do u take it out of the quad. All the videos show it after they take it out

[@betsypwnsyou]

Mounting bolts caused the issue ?

[@hawkskyflier]

Richard Green, I called my dealer and he replaced the part under a warranty. I put it in, that’s when I found out that the paint was never removed behind the relay switch. Before I installed the new switch I sanded off the pains all around then applied electric grease on the bare metal for contact and the new one works great both ways. If you’re having this issue I’d remove the relay and clean off the paint Jeffrey you do anything else. Hope this helps

[@betsypwnsyou]

@@hawkskyflier yeah this fixed my issue also thanks for making this. Bad grounded solenoid from factory wtf fail

[@Zandian]

For anyone that has and fixed this ground problem did it happen sporadically? Mine does it on and off and drives me nuts. Seems to happen more when the machine gets wet after plowing for awhile. And could a solenoid fail sporadically or is it usually an all or nothing kind of deal?

[@dennisisaac746]

Got same problem

[@stephenevans-2paradox767]

I have a 2018 570 x3 and winch goes out, but not in. I did the “remove the paint on front and back of solenoid and on the bracket as well”, as you explained here, but it still doesn’t reel in. I did not replace the solenoid though. It still just clicks each time I push the “in” button. If I hear that click each time I hit the button, does that mean the solenoid is good?

[@hawkskyflier]

Hey Xodarap1 2p... As long as you cleaned of the paint real well.. on both the frame of the bike & the solenoid it should work. If it doesn't I think that the solenoid is out. Just like on my son's Ford Expedition. The starter solenoid went out... but still clicks. If you cleaned up the paint, then mounted it tight again, but the solenoid just clicks.. i think you need a new solenoid.. sorry buddy.. :(

[@stephenevans-2paradox767]

hawkskyflier that’s ok. I have one on order already, it will be here on Monday. I just didn’t know if the solenoid could still be bad if it clicked. I really didn’t want to be back to the dealer for a new winch motor. Thanks so much for your video and for the reply! 👍