2021 Ford Bronco Sport Oil Change 1.5L Engine FAST & EASY IN 4K

[@jovannyjimenez7266]

Dude thanks for this Video and sharing the links, I'm looking forward to do change the oil on my Bronco! Great tutorial video man!

[@cm1133]

Learn the “flood start” procedure to fill your new oil filter with oil PRIOR to starting the vehicle. This was a procedure that FORD created for these 1.5 L motors since the oil filter is horizontally mounted.

[@summerforever6736]

Thanks for the video this is what I was looking for

[@TheRealJoePas]

Do you have plans for front and rear rotor and brake videos soon?

[@Eddiee602]

Thanks for the video very informative. 👍🏼

[@michaelboortz8927]

Good to see young men working…

[@jamessowards3822]

The recommended amount of oil is 5.3 quarts. Another source listed 5.5 quarts so your level may register just a little bit low but not a harmful level.

[@Benerfe]

Can you do a coolant change?

[@themessyscrapper5010]

I love supertech oil. That's all I used on my Toyota Highlander and it had 315,000 miles on it when some birdbrain crashed into me and totaled it. I'd still have that car and by now I would have more than 500,000 miles on it because it was a great car.

[@pandadimsumtruck3757]

For 2024 1.5L the oil plug is a reusable plastic one. The oil pan is also plastic and takes 6.6 qts (!). note the factory filter was 1 in shorter than the replacement fl910s filter 2.25 in versus 3.25 inches. 15 nm (11.6 ft lbs) torque was printed on the factory filter. the 2024 (big bend) also lost that engine cover

[@chrisretired5379]

Thanks ! Just bought a 2024 myself, going to change the first oil @ 1500 miles. If mine has that cardboard ‘pan’ cover, I’m going to delete it as well. That and will see if the 2024 PTU has a drain plug 👍👍

[@Broncofan-4life]

Are you sure there wasn't a door on the shroud that can be opened to allow access to the oil plug and filter? I thought I saw that. Just asking, I don't know.

[@RobustArid379]

How much do they charge at jiffy lube 10min speed oil changer?

[@johnmacqueen1777]

Great video! Thanks.

[@AliAli-kc4tv]

How to unlock the 2022 Ford Bronco Sport transmission

[@livlife_tm]

Thank you brother!

[@HighEatzs]

Your about a half quart low, it needs to be at the top dot , its operable of course but wouldnt recommend running it at minimum.

[@stanmalmquist7536]

What is the correct touque for the drain plug

[@summerforever6736]

Good and tight

[@ThePounder001]

Is there not a drain plug crush washer?

[@silversentrav]

Just did this on my wife's BB, it has a rubber gasket on the plug. I called the dealer and was told that they didn't stock the gasket; but they had the plug w/ gasket. I just reused the gasket, The gasket is recessed in the plug.

[@samfrancisco8095]

I've never replaced a drain plug ever in 60 years and over 8 different cars. The only time I did is when the shop I used once with a coupon put the filter and plug on so tight I had to use vice grips to remove the plug because I stripped it and also had to use a screwdriver to pierce the filter with a screw driver to get it off. I do my own oil changes. $100+ now when oil and a filter cost $35 anywhere.

[@BeardedFordTech]

Everything was good. Until you lubed the filter o ring. I'm a master ford tech. And it literally says in workshop manual "do not lubricate filter o-ring". This is something ford put out a while back. It can actually cause the filter to back off. Your supposed to remove old filter wipe the surface clean and install new filter. Other than that. Nice video. Let me know if you need help with anything on it.

[@Mudblud]

Lubed it with dirty oil at that

[@BeardedFordTech]

@@Mudblud for real smh

[@summerforever6736]

Bull crap makes no different he used used oil for som lubrication you clueless!!!

[@randypetty3066]

The dirty oil on the new filter seal was the way I was taught too many years ago! Thanks for pointing that out.

[@lukeWiz44]

??? The box on motorcraft filter shows to lube the o ring in the diagram. I’ve never heard of not lubing the o-ring. there would be no logic there. It helps it slide on the metal surface of the mounting location, and not get stuck the next time.

[@ajsmith9995]

Nice review. I like to replace the oil pan plug and filter, put new oil in and start the car. Check for leaks underneath and then replace the shroud.

[@summerforever6736]

That is a waste of time !! If all tight no leaks !!!

[@samfrancisco8095]

My Jeep Cherokee has a door for the plug and filter access.

[@Sami-rp7mf]

Great job. I need to get this done. Oil life shows 45% and this is the first one so thinking to do this now at 4k. With synthetic I guess we can wait until say 6k. Right

[@summerforever6736]

You waited tol long

[@creekcomber]

I hate the shrouds but good vid

[@randypetty3066]

I will find that socket and wrench I dropped when I remove that in that shroud!

[@summerforever6736]

Do you have the model number for the filter ford used the one you toke off?? I wanna do a first oil change at 1000 and I wanna use the same filter so they wont give my friend a hard time later... Thanks

[@ThisPartIsAndrew]

I count 13 T30 screws

[@ljohnpeoples3106]

Always coat the filter gasket with new not the old oil.

[@summerforever6736]

Makes no different !!! Load of bull crap!!

[@luismontoya5973]

Wear goggles my man. You dont wana get oil and metal fragments in your eyes