I have the same Goldstrike accessories Chris. I found the brake cover raised the height beyond stock. This caused me to be unable to rest my boot toe on the pedal without activating the rear brake light. So the pedal is adjustable and I lowered its height to allow a resting position. The adjustment also will if not done correctly cause the brake light switch to remain on. The trick is to adjust both and allow your boot toe to float above the pedal and at the ready to step on the brake. Otherwise I was originally forced to move my toe onto the floorboard or cant my boot to the outside not the optimum preparedness position. Lesson learned. Manual shows how to adjust both.
@chriscaliente50332 жыл бұрын
If the brake pedal is lower than the foot rest, you may have a longer reaction time trying to find the rear brake therefore I set my brake pedal in a higher position and keep my boot to the rear of the pedal. The beauty of the floor boards is their adjustability, each rider can adjust their foot resting positions to their desired comfort level, up down forward or back until the best position is found.
@SecurityBob2 жыл бұрын
Yes I tried all positions Chris and found my foot size 11 was stressed keeping to the rear of the elevated cover. The reaaction time for me was straight down rather than lift , forward then down which seemed quicker to me. But I see your option too and it I guess is muscle memory and personal comfort. Just a thought I wanted to share. Changing from OEM footrests to the Goldstrike small boards led me to this observation. Love your videos. 👍
@chriscaliente50332 жыл бұрын
@@SecurityBob thanks for sharing your story, I’m sure that someone will benefit from your experience, thanks.
@lpete5312 жыл бұрын
Chris installs are the best, he doesn't do a lot of cut editing, shows us detailed install
@chriscaliente50332 жыл бұрын
Thanks I appreciate it!
@stancook28882 жыл бұрын
Chris, after ordering these items for my 2021 GW DCT Tour, I shouldn’t have any issues installing them thanks to you. Much appreciated as always!
@chriscaliente50332 жыл бұрын
Your welcome, I hope my installation video helps.
@summerb95788 ай бұрын
Thank you for the video. I just received both of these as gifts this year (plus the Goldstrike tie down points) and am looking forward to installing everything.
@chriscaliente503323 күн бұрын
Glad it was helpful!
@lakesidelew25122 жыл бұрын
Good job Chris !
@chriscaliente50332 жыл бұрын
Thanks
@johnharland23362 жыл бұрын
After watching several of your installations, I have to say, you are explicit, detailed and thorough. Refreshing! I will visit often.
@chriscaliente503323 күн бұрын
Thanks so much!
@jgoogleheim88807 ай бұрын
Great video. Ordered both items for my 23 DCT bagger using your code and it worked. I caught my left landing leg pant on the stock footpeg once coming to a stop so the floorboard is perfect. Got the pegs and brake pad and installed and adjusted them. The left floor board has to be mounted as you show to avoid the kickstand. They feel good sitting on the bike and will try them out when the snow and salt are gone. Thanks!
@chriscaliente503323 күн бұрын
Glad it helped
@dannodog2 жыл бұрын
Thanks Chris! I just ordered them, but the Blacked Out version. Great video!
@chriscaliente50332 жыл бұрын
The Goldstrike black version looks really cool too but since I already have the chrome 3 way adjustable highway pegs on the bike, I wanted the floorboards to match, with color you can’t go wrong!
@freerider70642 жыл бұрын
Thank you Chris!!
@rugby38746 ай бұрын
Good job, Thanks.
@enjoyingretirement48462 жыл бұрын
Good instructions.
@DavidSmith-fw6uj2 жыл бұрын
Love from DeKalb Mississippi USA 🇺🇸
@unicornhairhead Жыл бұрын
Thanks Chris. Your the best. A very simple installation but without you who would know. I have a six speed and I’m not sure if I’ll get the floorboards but the brake pedal cover looks great. I love all of Goldstrike’s stuff so far. Quality and looks and who supplies color instructions? Only Goldstrike.
@chriscaliente503323 күн бұрын
Glad my video was helpful, thanks for watching!
@RH-qf6wvАй бұрын
I just installed the Black version of these. Would not recommend them. The paint is too thick for them to mount properly and chips off when installing the bolts. I removed and reordered the chrome version. Just my experience yours may be different.
@Nightboat4 ай бұрын
While I appreciate that owners make detailed videos like this, they really should try to get their facts straight before publishing something that perhaps many people will watch and then copy. Perhaps it is just semantics on the first thing but it is a COTTER pin, not a CARTER pin. The bolts for the min-boards actually require a 1/4 hex to tighten/loosen. A 6mm will work but it is sloppy and could cause damage to the bolt. For the brake pedal cover, Goldstrike recommends right in the instructions using some threadlocker on the screws. Ride safe.
@200papabear2 жыл бұрын
did you add blue lock tight
@furchaser2 ай бұрын
blue lock tight
@stevenkraus16792 жыл бұрын
I installed these but ultimately removed them because it reduced lean angle and I kept scrapping them. I kept the hwy pegs but still have to be careful with those if I'm leaning the bike.
@chriscaliente503323 күн бұрын
I’ve never had that problem with leaning.
@MrBubbajohnson12 жыл бұрын
How do u like the floor boards Chris? Thanks
@chriscaliente5033 Жыл бұрын
I love them!
@Todesjaeger00 Жыл бұрын
WIsh I had found this video before I purchased the floorboards for my 2023 Tour DCT to get the discount :P Since I have a black goldwing, I went with the black gloss floorboards. The driver adapters were extremely tight in the mounting flange. I thought it was the thick paint, so I sanded off some paint. Left side was still tight (moreso than the right)..left does not move, but on the right one, I can move with my hand, but still too tight for the spring to do its job. The flanges on the adapters seemed spread beyond being parallel. Kind of disappointed in the quality.
@jgoogleheim88807 ай бұрын
My black floorboard was too snug on the left also so I sprayed wd-40 down the pin and flange joints. Worked the board up and down a few times and now the spring works and the board moves smoothly.
@bryanttaylor3582 жыл бұрын
These look much lower than the stock foot pegs. Do they scrape when leaning hard?
@chriscaliente50332 жыл бұрын
They will scrape if the rider tries to prove how big his testicles are by leaning the bike over 90 degree into a sharp curve but hopefully by then a witness has already dialed 911. If a rider rides responsibly he or she will not have any problems…
@bryanttaylor3582 жыл бұрын
@@chriscaliente5033 Bah ha ha ha! Well played, sir. Seriously, though, my Kuryakin highway pegs drag a bit on hard turns (slow speeds). Just curious if these might further limit turning. I'm no moto-racer wanna-be; too old for that nonsense.
@chriscaliente50332 жыл бұрын
@@bryanttaylor358time will tell if these floorboards are worth it, so far I am impressed with Goldstrike accessories for the 2018+ Goldwing. I haven’t heard any issues of Goldstrike floorboards dragging but I will keep the channel posted!
@desertkubota93932 жыл бұрын
@@bryanttaylor358 scrape easily. I am not a hard leaner but am not worried about turning into a corner either. They scrape easy. Not Goldsrikes fault it is the position of the GW. However it would have been nice to have a replaceable strip on the bottom of the floorbaord. The floorboards do flex up so no danger of “catching” the street. 21 GW -Ken
@bryanttaylor3582 жыл бұрын
@@desertkubota9393 Thank you for the evaluation, Ken.
@sumncguy10 ай бұрын
for god sake man !! Cover that pipe with a rag !!
@EgbertMims Жыл бұрын
These floorboards make it impossible to ride with anything other than thin tennis shoes if you don’t have a DCT. Because there’s not enough room between the shifter and the floorboard to get your foot in. So I am getting a heel Dash toe shifter.