22-M04 Touch Lamp Repair: How to get your lamp back to life

/ ourheritageworks
/ ourheritageworks
Thank you for watching, liking, sharing and commenting!!
Touch lamps were very popular at one point but they lost popularity because the stopped working. If you go to a thrift store you will probably encounter a touch lamp.
So how do you fix it? There is a control board in the base that normally is the problem. It is also possible there is a bad wire or a faulty socket.
When ordering a touch lamp be sure to get one that can support your usage. When buying the bulbs make sure you get ones that are dimmable and match your control board. In this example, I use dimmable LED lights. The bottom two levels work great. The top level will sometimes "flicker". This is because we are hitting the limit of the board and it doesn't have quite enough power to fully light the LED bulbs. I have also used cheap candelabra bulbs. They work fine but they don't get as bright. The control board I have is rated for LED and Incandescent bulbs. Some are for LEDs only or Incandescent Only. Also, this control board is for three levels of light and an off. Some boards are on/off only. So make sure you look at what the board supports when you go to order the boards.
If you look closely, the original board is wired differently than what is shown in the replacement board diagram. It is wired on the white wire instead of the black one.
Music:
Neverland by Alexander Nakarada
Emotional Piano Improvisation by Alexander Nakarada
Reaching The Sky (Long Version) by Alexander Nakarada
Rustic Ballad by Alexander Nakarada
www.serpentsoundstudios.com
Music promoted by www.free-stock-music.com
Attribution 4.0 International (CC BY 4.0)
creativecommons.org/licenses/...
#OurHeritageWorks #TouchLampRepair

[@robbyers7614]

Really didn't think I could repair my touch lamp but after seeing this video I'm going to give it a shot Thank you very very much.

[@tim.h9765]

Found this video after a search as my lamp is now always on. I'll be ordering a module tonight and will get back to tell you how the repair went. Thanks for a very informative video

[@hrhdotp]

I don't even own a touch lamp, but was interested to learn. One never knows when a touch lamp might find me! Thanks for sharing your many talents.

[@ourheritageworks]

Thanks Priscilla, I like doing these small projects. I actually have repair another one since I filmed this. Normally, touch lamps can be found at yard sales and thrift stores pretty cheap. Now you can get a nice looking one and update it. I am thinking about making a light that is touch sensitive, but it is still in the planning stages.

[@paigeburgess9323]

My grandma passed away last month, she always had this lamp in her living room and I just got it to use in mine, luckily there’s a switch on the plug so I can still turn it on/off but was bummed to find out the touch function wasn’t working. I’m very excited to see there’s a chance I could restore it to its former glory, thank you for the tutorial:)

[@angelopcs]

I have the same lamp (except the Looney tune characters that were blurred :), same problem. I wish all tech youtube fixit videos were this thorough. My lamp is working again. Thank you.

[@suesmith9184]

I’ve had a touch lamp sitting for the past 3 years because I could not follow the wiring instructions. None of the videos had the same color wiring or same number of wires. Your instructions were easy to understand although your module was very different from mine. Thanks so much!

[@ourheritageworks]

You're very welcome. Please be careful though, each control module might be slightly different but the basics should be the same. And remember if in doubt, have a professional do it for you. Good luck!!!

[@SAX4GOD]

Excellent advice. I was able to repair my two lamps. Thank you!

[@tylerbug2009]

I'm having trouble with the same lamp. Our dog had nipped the cord and I was hoping that was the problem but no luck. Time to find a new controller for it. I really do like the lamp and I'm looking forward to having it working as it should again. Great video!!

[@user-hm8rt8nm5e]

Thank you for your clear instructions

[@GravityFlavoredPie]

Thank you so so much, I was able to repair my touch lamp!!!

[@marciaschmitt3748]

Also I just rec'd the new controller. Have not installed it yet. Your instructional video is perfect. I will follow as described.

[@jdub8766]

Thank you for posting this video, it helped me alot.

[@tanushreerajan2398]

Your video helped me repair our touch lamp! Great advice and excellent video. Thank you!

[@radishpea6615]

aving watched your video I am going to try and fix my lamp, thanks.

[@richhk9388]

Great video!!! Thank you so much!

[@Heisstrong]

That was fun to watch and interesting. Thanks!

[@ourheritageworks]

Glad you enjoyed it. Thank you for watching and commenting!

[@amaliaenciso1928]

Tengo tiemo que mis dos lámpara touch no funcionan, pero como me gustan tanto no quise tirarlas, despues de ver este video, comparar los reemplazos. Muchas gracias por el video.

[@ourheritageworks]

Me gusta mucho este estillo de lampara tambien. Espero que sus lamparas funcionan bien ahora. Gracias por verlo.

[@aadarose]

I have the same lamp, the problem is that the touch sensor kinda works. The light stays on well, but every time i touch it to turn it off, it switches back on after a while. I’ll probably open the lamp if it doesnt start working, and return back here to update how it went! Thank you for the advice!

[@a.k.3659]

So... You were electrocuted?

[@SandraSlater-ky9jn]

I have a light on that same order. Just wondering if there is a certain control module that you have to get? I look on Amazon and there's so many that you can purchase.

[@loveiselasticcreations3663]

My lamp is a month old. Instead of a new module, can I just use a touch lamp socket?

[@billmarino4360]

You could have used crimp type connectors. Buchman’s is the trade name

[@Creatively_kawaii]

How to clean it from rust?

[@Marcoosianism]

Any advice on how to actually diagnose and repair the circuit board on the existing module? I find most of the replacement modules are absolute junk and either don't work as well as the original or burn out soonafter replacement. I'd like to be able to replace bad parts on the component level.

[@ourheritageworks]

No advice. I find most electronics these days are like that. They are either good or NOT good. There seems to be little in the middle. Since it is an integrated circuit board inside, I don't think a "normal"/"average" person would be able to fix them. Good luck.

[@Marcoosianism]

@@ourheritageworks Thanks for your thoughts.

[@davidarowosafe1154]

My lamp didn’t come with a control module… so I really wonder how they made the touch work… it’s stopped working tho

[@marciaschmitt3748]

I accidently dropped the lamp & broke the lamp glass pieces for the shade. Can I buy the glass pieces?

[@ourheritageworks]

Occasionally I see them on Craig's List, ebay or in a thrift store. You could also, replace the lamp shade with a more traditional one. Good Luck!!

[@ourheritageworks]

I posted a follow-up video recently. You might want to review it as well. Good luck. Remember, if at any point you become uncomfortable with it, call a professional.

[@jsand7028]

I have the same type of lamp, followed your instructions. I always check with a non contact ac tester on the housing and I have electricity on the housing. I measured then with a multi meter and it shows me 92 volt. Is that safe to touch ?

[@ourheritageworks]

First, I am not an electrician. Please contact a professional electrician if you have any concerns. The purpose of my video is to show how to change the module and not how the module works with the lamp. I have never tested the voltage or current on the surface of the lamp. It is a 120V system. I know that there will be some voltage and current on the surface because that is what makes it a switch. I DON'T KNOW HOW MUCH VOLTAGE OR CURRENT SHOULD BE THERE. The manufacturer of your control module should be able to tell you what to expect to be on the surface. AS A PURE GUESS - the voltage will be system voltage OR extremely low voltage (millivolts). Either way I would expect the current to be miniscule (milliamps or microamps). AGAIN PLEASE contact the manufacturer of the control module or a licensed electrician for more details. I'm sorry that I can't give you a better answer. IF you find out, it would be good information to add here.

[@franboban3409]

Hello. I'm following your instructions but while I was removing the tube cover, some copper color scrapings fell out. I used pipe cleaners to get most of it out. Will this stop the lamp from working. I could send you a snapshot.

[@ourheritageworks]

The answer is “I don’t know”. Even with a snapshot I might not know. I would have someone near you look at it. It might be nothing or it might be really important. You will need to find the source of the copper material and then determine if it is an issue. Please check it thoroughly and consult a professional if you are not 100% sure.

[@stephenmccoy4625]

I did this twice and the control module blows out..what could be the issue?

[@ourheritageworks]

Stephen without being there, it is really difficult to tell. It probably means that you have a short somewhere. Either the modules are defective (not likely if they are new but it does happen), the wires in the lamp are shorted, the sockets on the lamp could be bad, the wires to the module could be connected wrong or the modules might not match your country and voltage/current/wattage. My second video shows a little more about reading the diagrams and matching the module to the lamp. kzbin.info/www/bejne/iqfXgn-ObMl7fbc In my second video, I discovered a bug had wedged itself into the socket. That would have created a short circuit if I had not found it. Another KZbinr had a similar issue, See Andrew Camarata's video kzbin.info/www/bejne/a6DPoZxpg8d_sNU @AndrewCamarata. It might help as well. Please if you are unsure, consult a professional.

[@colorfulcheshire4181]

Apparently a lot of these lamps HATE LED bulbs. I'm having trouble researching if it's possible to convert mine to LED rn bc incandescent bulbs are so hard to find and pricey

[@bradyhope2730]

wondering if you could help me out , i have a lamp just like yours and i changed the sensor in it and it works as soon as you turn it on , but after leaving it on for a while it want dim are cut on and off , what can i do???

[@ourheritageworks]

I’m not sure. Initial thoughts… 1. did wires get crossed / is it wired correctly according to your switch specifications. 2. Is it a faulty switch/sensor? 3. Is the bulb rated for your type of sensor? The type of bulb must match the sensor (led, incandescent, halogen, etc) If it is working and then stops working it is probably an issue with the sensor. My guess it is underrated for the amount of current running through it and it is over heating. Hopefully an expert on the subject will jump in with a response. I am a DIY person and can only show my experience.

[@bradyhope2730]

@@ourheritageworks thank you so much. I think theres a short in the sensor . Sending it back thanks again j hope

[@melissahollingsworth6101]

@@ourheritageworks Hi. I also have an older lamp like this that has three separate bulbs. My controller went out and I tried replacing it with one module and it popped when I turned the power on -didn’t work. Could you please tell me which module controller that you are using because my lamp is identical, thank you. 3:43 M.H.

[@ourheritageworks]

@@melissahollingsworth6101 My controller might or might not work for you. If you "popped it" you could have a short in one of the wires or a mismatched controller for the bulbs that you have installed. In the second/follow up video I discuss matching the controller to your lamp needs. No matter what please be careful and consult a professional if you aren't sure.

[@JanetCarter-y2z]

Where can I buy this please

[@ourheritageworks]

I got mine on Amazon

[@bonniemunday4711]

Where does the brown and grey wire go?

[@ourheritageworks]

I’m not familiar with a brown and gray wire setup. There should have been a wiring diagram with the switch module. Be sure to follow that. The key is understanding the light you’re rewiring and being able to read the diagram from the switch manufacturer. I’m sorry I can’t give you a better answer. As a disclaimer/reminder, I am not an electrician. If you are unsure, please be careful and if needed contact a professional.

[@reneperez7000]

What can I do if I want my touch lamp to always be on?

[@codymumford4583]

Don’t touch it

[@Marcoosianism]

You can always just remove the module and directly rewire the neutral of the plug to the neutral of the light socket and the hot of the plug to the hot of the light socket. But now you'd have to unplug and replug the lamp if you want it on and off. Or just add in a switch to the cord.

[@nilolee2426]

What’s the part number for the module?

[@ourheritageworks]

It is going to depend on your needs and country. For 120V (U.S.), the model in this video is X0033SWHN5, but it could be different the next time I order. I am working on a follow up video. Search your needs how many volts, watts, etc.

[@ScottyD]

Where did you order your module?

[@vickeyricher9537]

Too much talking and unclear. The only way it could be helpful is if I had the same fixture. This is light unit specific.