#229

Music by Aylex - Urban Journey
INSTA - / kamijuins
E-mail - [e-mail]
- How to control two receivers synchronously via remote VX1
• How to control two rec...
- buy them can order
flipsky.net/co...
- Flisky products discount code: KAMI
Discount products list:
-FLIPSKY FT85BD Dual ESC With Aluminum Case NON-VESC For Electric Skateboard / Scooter / Ebike Speed Controller / Electric Motorcycle / Robotics
-Brushless Motor Sensorless Amphibious Fully Waterproof motor 65161 120KV | 100KV 6000W for Efoil | Ejet boards | Ebike
-Flipsky FSESC 75450 84V High Current 450A ESC Base On Vesc With Aluminum Case Water Cooling Enclosure For E-Foil Fighting Robot /Surfboard AGV Robot
-Flipsky FSESC 75350 84V High Current 350A ESC Base On Vesc With Aluminum Case Water Cooling Enclosure For E-Foil Fighting Robot/Surfboard AGV Robot
-Flipsky FSESC 75300 84V High Current 350A ESC Base On Vesc With Aluminum Case Water Cooling Enclosure For E-Foil Fighting Robot/Surfboard AGV Robot
-Flipsky 75100 Pro V2.0 With Aluminum PCB Based on VESC For Electric Skateboard / Scooter / Ebike Speed Controller
-Flipsky 75100 Pro With Aluminum PCB Based on VESC For Electric Skateboard / Scooter / Ebike Speed Controller
-Flipsky 75100 V2.0 With Aluminum PB With Power Key Switch Button Based on VESC For Electric Skateboard / Scooter / Ebike Speed Controller
-Flipsky 75200 Pro 84V High Current With Aluminum PCB Based on VESC For Fighting Robot Surfboard AGV Robot
-Flipsky 75200 Pro V2.0 With Aluminum CB Based on VESC For Electric Skateboard / Scooter / Ebike Speed Controller
-Flipsky BLDC Belt Motor Battle Hardened 6354 140KV 190KV 2450W for Electric Skateboard
-Flipsky Sensored Outrunner Brushless DC Motor Battle hardened 7070 110KV 4200V
-Flash Deals LCD Screen Remote VX4 for Electric skateboard | Ebike | Eboat compatible with VESC
-Flipsky 2.4G Wireless Module Waterproof Remote VX3 Pro controller For foil | Esurf | ESK8
-Flipsky 16.3* CNC New Upgrade RKP Trucks For DIY Electric Skateboard | Longboard | Esk8
2.4Ghz Remote VX1 Pro for DIY electric skateboard

[@KAMiJUINs]

Because it was a new attempt, it was a project that took a lot of time. It was only half a success, but it was a fun challenge and I learned a lot in the process. Please refer to the description box for additional information. 새로운 시도였기에 시간도 많이걸렸던 빌드 프로젝트였습니다. 절반의 성공이였지만 과정에서 많은것을 얻은 즐거운 도전이였습니다. 추가정보는 설명란에 있으니 참고하세요.

[@Aitalk82]

Ahh.. thanks bro , i always waiting part 2 , because i want to know how to linked 2 receiver in one remote 😂😂

[@Aitalk82]

Is the method all the same to linked 2 receivers with one remote? for any brand of remote?

[@KAMiJUINs]

Not really. Those recivers were other firmware updated. If you buy, please check with Flipsky before purchasing

[@anwin85alon]

pmme come malaysia

[@peugahwhy]

Makes me nostalgic for the "air gear" anime..

[@willipine1863]

Finally real Air gear👍 my childhood anime comes alive

[@xsjdnxkx2070]

Me dos(2) I wonder if there will be regalia

[@KAMiJUINs]

Thank you for watching :)

[@Sm00k]

I FOUND MY PEOPLE!

[@stephanhepburn2508]

Thanks kami , i have been waiting for ( AT (AIR GEAR) build for years

[@KAMiJUINs]

HaHa, Sorry for that :-) Thank you for waiting and watching!

[@shakysugars]

deadass

[@ssoffshore5111]

As I mentioned in your first video, you need to switch over to wheels with a rounded profile. The reason they feel more like skis is because of the flat profile wheels you're using. Once you switch over to wheels with a rounded profile, you'll be able to lean and turn like on rollerblades. Please humor me and try it. 😉

[@KAMiJUINs]

Thank you for your opinion :-)

[@phobosspoof]

Not sure if you’re interested in this but if you used Omni wheels you could create assisted turns and wouldn’t need to lean really.

[@micahevans969]

I agree flat profile wheels just dont make sense inline style wheels rounded off would have better result forsure

[@FRZNCode]

Hey Kami, this is a great build, especially when it's something you haven't done before. I think the reason it was difficult to turn or walk in those was because of you using longboard wheels rather than something like inline skate wheels which you would only need to lean to turn (but then you would likely have to 3D print custom pulleys to fit for those wheels and belts, and would be less stable for you if you haven't inline skated before). If you want to go faster, probably a bigger VESC would help (may need to be put on the back behind the snowboard bindings if it can't fit where it's original section). Maybe adding another battery connected in series would also help (but would then need to be put on the back behind the snowboard bindings in like a small bag or something). But if doing that, then the bigger VESC would likely need to be relocated to the top of your feet of the snowboard bindings (somehow). Doing all of this would lead to better specs and performance, but would make it heavier and not as clean/professional looking as yours.

[@KAMiJUINs]

Thank you for your opinion and watching :-) FYI, the ESC I used this time could have brought out a much stronger output, but as in the video, I limited it to a current of 40A. And the battery of the additional serial connection for faster speeds is likely to get heavier as you say, so I don't think I can

[@Yuriel1981]

I actually think you should lock-hinge the back supports and include an shin/ankle restraint. Give the hinge around 30 degrees of arc from say 110 to 70 degrees. Most inline skates depend on good ankle support for maneuvering. That and switching to a more round wheel will allow an easier lean turn control. Which seems like a good hybrid for the ski/skate design you are working with.

[@jamesbown2612]

Air Gear vibes and im here for it!

[@KAMiJUINs]

HaHa :-) Thank you for watching

[@DanielKwan]

I request an ASMR cleaning video because that is the cleanest workshop I’ve ever seen. And that is a really refined looking prototype!

[@KAMiJUINs]

Thank you for coming and watching, Bro :-)

[@animecademia2573]

love watching you two ❤️

[@Racule]

새로운 도전은 언제나 보는게 재밌어요

[@KAMiJUINs]

그렇다면 저는 매우 보람을 느낍니다. 하하!

[@MrTysonv]

Best design i have seen of powered skates so far, awesome job they are sick

[@KAMiJUINs]

Thank you soooo much :-)

[@braxwhitney]

This is so fascinating! I hope big companies can help innovate this DIY into a stable esk8 platform! What a pioneer!! 🤩

[@KAMiJUINs]

Thank you for saying that :-)

[@esk8Kyle]

Hey Kami! That's an awesome build. I would of used Hota pneumatic wheels instead of mad PU wheels. The trick with rollerblading is to lean on turns and I feel with PU wheels being so flat, it's hard to turn. Also u won't need to raise the skate if u are able to lean side to side. Other than that this is wayyyy better than the other e-skate that u made a video of. A bit of fine tuning and I think there's a market for this in Canada. Do u want to work together on this? I build can build molicel packs so that will help with making the battery more compact and thin...

[@KAMiJUINs]

Well...Let me think about it :-) Thank you for your opinion and watching.

[@thisfacelol5049]

1 step closer to air gear❤❤😍

[@KAMiJUINs]

Thank you for watching :)

[@leftpalmofbuddha6116]

This was awesome. 100% success and I love your dog

[@KAMiJUINs]

Thank you so much :) and watching it too.

[@da420burna]

Great idea. I think you should try hub motors..for free roll. To extend range. Also a more narrow contact patch wheel 🫡. I’m no expert just throwing ideas around. Fantastic video🔥

[@KAMiJUINs]

Thanks for the suggestion and watching :-)

[@binghao0102]

I noticed that when you're riding straight, if your tire isn't round enough, your foots can inadvertently come closer which can be dangerous and could even cause a fall. In my opinion, I suggest using larger and more rounded tires, as they can make turning easier.

[@KAMiJUINs]

Thank you for your opinion and watching :-)

[@omdesigned]

I LOVE these!! I made some specialized protective gear and a Wing that's perfect for them!!! Let's go!

[@KAMiJUINs]

Haha! Thank you for watching :-)

[@eBoard3R]

*Nice to see the follow-up!* 🤟🏽⚡️🤙🏽⚡️🤟🏽 mazin build, I smiled at 12mins 30sec when Kami gave the look and the music started with the project done 😁 Another cool project!! ❤

[@KAMiJUINs]

Thank you as alway brother :) Yes, it took some time, but I had a great time to finish this project!!!

[@joelin4676]

Ladies and gentlemen , I present you god of handcraft

[@KAMiJUINs]

You're one of the really old subscribers. Thank you so much :-)

[@0248delltv]

I can't even begin to understand the complexity but I can say I still enjoy watching your videos.😊

[@KAMiJUINs]

Thank you so much :-)

[@_pacalis]

I've been looking for a build like this for the longest time. Really great work. In Europe in the summer, skiers use skates with this design profile to practice skiing in the summer months. Maybe you could look at them for design inspiration? But they use ski poles 😂

[@KAMiJUINs]

HAHA Thank you for watching :)

[@เสือดํา-ผ6จ]

personally I think this is a great accomplishment knowing that most if not all either skated mid to late 90s. As far as suggested improvements are involved i would: 1. trim weight from the bottom frame like how current skates on the market have like how most 110-120mm wheel freeskates are. 2. Make the frame compatible with most skate boots on the market. I understand the ease of use with just having to strap in with just shoes but it seems very unstable and unsecure when you are at an avg cruising speed 20-30 mph on skates. Ankle support is a must and securing your feet would stabilize the ride longterm. 3. Belt covers for the drive motor. I seen this in most eboards but I dont understand why they wouldnt implement this feature unless it causes the motor to potentially overheat or make it heavier. I point this reason out because on the road there is always a chance that the debris from the road would get caught into the motorbelt causing a mid ride malfunction. Wether or not I am right about this is rather an if and when situation. 4. If there was a way to program this with a neural glide on the handset. Call me crazy but if this would happen it would possibly change the possibilities of e-inline forever. Trick skaters catching that speed and potential of a grind frame would be something of jet grind capability. This eventually would be a realtime version of what we seen in most older games or comics. These are just suggestions but I see room for possibilities in the future with seeing what is crafted. Great vid and keep up the good work! 👍🏼👊🏼

[@DrewElia]

brother you never stop amazing me! this is so cool! keep pushing the boundaries!!!!!

[@KAMiJUINs]

Thank you so much, Brother :-) I really hoped to be able to meet this year, but it's been tough to make time. I'll try to prepare in advance next year so I can go. See you then!!!

[@trevication]

Once again bro great innovation. Wheels need to be thinner for sure but I already am sure you know this. Perhaps if you find a way to use the larger inline skate wheels or even better inflatable tyres which would improve the comfort and rolling resistance. I look forward to the next version. As you always look to improve. I like great minds

[@KAMiJUINs]

Thank you for your suggestion and watching :)

[@oneeyedcat1822]

Try looking into a (temporary) locking mechanism for 2 or 4 of the wheels & maybe it will help with trying to walk when you need to. Magnetic locks could be a good choice. You already have the power supply & there are loads of designs of mag-locks. And they turn on & off. A thinner rounded-edge wheel in the front may be enough to make it more steerable. Good Luck.

[@kenschulman-specializedend6061]

Well, you got em’ done! Nice work!

[@KAMiJUINs]

Thank you for watching :-)

[@arranwilliams2523]

that is truly wild!!!

[@KAMiJUINs]

Thank you for watching :)

[@Mr.Unbreakable83]

This is a cool project

[@KAMiJUINs]

Thank you for watching :)

[@pepedel13]

Nice vid as always!! I was just thinking about building electric inline skates.... and then you just uploaded a video! I would suggest you to change tires to another with round contact shape instead of squared. With inline skate you want the less contact shape you can, so you can move them muuuch better... Bcs I guess it will take a huge effort to make a simple turn with that tires and weight!

[@KAMiJUINs]

Thanks for the suggestion and watching :-)

[@_Zer0202]

They are great bro, I love their design. great review 😊👍

[@KAMiJUINs]

Thank you as always Bro :-)

[@류랑-w2b]

와...이건 정말 위험해보이네요 ㅠㅠ 안전이 최고입니다!! 항상 조심하세요

[@KAMiJUINs]

네 감사합니다 :)

[@ZEAL_FPV]

@KAMiJUINs Awesome project!! But those batteries NEED to be replaced for your own safety! I personally wouldn't use them for anything that requires a load from the motors, but for bench testing; they should be fine... evenso, I would be cautious around them if you decide to keep them ONLY on your bench ( in a Lipo Safe / Bag ). Storing them in a air-tight ammo can would be the safest solution beyond safely disposing them ( more on that later ). When a lipo swells up, it's caused by 1 of 4 things... 1. Over charging, which is caused by higher than normal voltage input during battery recharge. 2. Over discharging, is caused by over using a lipo past it's minimum safe voltage cut-off point. 3. Over exposure to Heat, this causes the chemicals in a battery to react and swell up with the potential to explode or release a jet of flame. 4. Aging and wear, over time the batteries naturally degrade due to normal use and eventually puff up. When a lipo puffs up it's a physical sign that they should be discharged safely and replaced. Don't throw lipo batteries in the trash, Don't puncture them with nails or burn them. They can become explosive and release very toxic chemicals into the environment ( even worse is if you breath in the gas ) !! There are products you can buy online to Safely Discharge lipo's down to ZERO volts and they're relatively cheap to own. After the lipo's have Zero Volts, you can recycle them at a local Electronics Store; they have programs where they will ship the batteries to factories to recycle the chemicals to make NEW Batteries!!

[@KAMiJUINs]

Thanks for the suggestion and watching :-)

[@gravityfuzz]

Looks cool. Cloudwheels would be nice on there.

[@KAMiJUINs]

It may be so :-) Thank you for watching!

[@Brennen_Nisporic]

Great video cool to see you building different things.

[@KAMiJUINs]

Thank you for coming and watching bro :-)

[@hwk1632]

뭐죠 이 대단하신 분은...

[@tmzkdl7017]

프로토타입이 이렇게 완성도가 높다니... 솔직히 저기에서 타이어 디자이만 수정해도 훨씬더 안정적일것 같아요!

[@KAMiJUINs]

시청과 의견 감사합니다 ~ :)

[@changhokim9893]

제 생각에는 변속기 밧데리를 백팩형식으로 묶고 발쪽에는 모터만 있는게 어떨까 합니다 구동부가 가벼워지면 크기도 작아지고 타기도 쉬울것 같습니다 차도 휠이 가벼우면 핸들링이 좋아지는거 처럼요

[@KAMiJUINs]

먼저, 제가 이번에 스케이트를 이렇게 디자인한 이유는 와이어를 매달고 타는것은 뭔가 전동 스케이트로서의 완성도가 떨어진다고 보았기때문입니다. 그래서 두개의 리씨버에 연동하는 방법으로 부품들을 매립한것입니다. 확실히 알게되었던건, 만들어보니 왜 전동스케이트가 출시된지 꽤 되었음에도 발전의 한계가 있었는지 였습니다. 제안과 시청 감사합니다. :-)

[@demonhogo]

This was great!! Really cool design process and aesthetic as always. Also, you should do a dark episode where kami tells you to do evil things.😎

[@KAMiJUINs]

HaHa, Thank you for watching like that :-)

[@leokim8219]

상상만 하던 걸 만드시네요 대단합니다!

[@KAMiJUINs]

봐주셔서 감사합니다!

[@Sensei.All.Mighty]

Looks neat and clean !!

[@KAMiJUINs]

Thank you for watching :)

[@EverybodyEditsHacks]

I am a skating expert. Ill come over and text the top speed of these bad boys

[@KAMiJUINs]

HaHa, Thank you for watching bro :)

[@GreenPlanet30]

Nice project ❤

[@KAMiJUINs]

Thank you so much :-)

[@IsaccNewten]

퀄리티가 좋네요

[@KAMiJUINs]

네 감사합니다 :)

[@NullBlox]

I think this is neat but I will stick with esk8. Very well built and looks very well refined.

[@KAMiJUINs]

Thank you so much, brother :-)

[@worachart111]

Very interesting diy build and good job

[@KAMiJUINs]

Thanks bro :-)

[@loklokey7882]

I enjoy watching your reviews whether if is a success or a failure.

[@구름나그네1999]

자이로 스코프를 응용한 가속을 하면 더욱 안정적으로 주행할수 있겠네요.

[@hanzstormrider]

Perhaps if you could find round profile wheels, it will be much easier to control regardless of its long length. Overall this is a cool build

[@KAMiJUINs]

Thanks for the suggestion and watching :-)

[@PizzaCologne3]

well done

[@KAMiJUINs]

Thank you so much :-)

[@jpjay1584]

nice project!! the problem with e blades is the V stance. its very static and not at all like roller blading. its not the length or the wheels. (humans need stability if powered both feet separately) can not change this. (unfortunately) and if use both feet parallel you will fall on your back.

[@KAMiJUINs]

Thank you for your opinion and watching :)

[@togsmovingcastle]

so sick!

[@KAMiJUINs]

Thank you for watching :)

[@meiyou_5168]

운동화는 발목을 보호해주지 못합니다 보드 부츠를 이용해보세요! 컨드롤하기 훨신 편해질겁니다 바퀴의 바닥면이 평평한것보다 둥그스럼한게 좌우 카빙이나 턴이 더 부드럽게 가능할것같습니다 스키어로써 침 뚝뚝 떨어지네요 ㅋㅋㅋ

[@KAMiJUINs]

시청과 의견 감사합니다 :-)

[@Catchmyep3]

Every very cool. Even more impressive ypu designed and built them! Maybe finding a thinner or more "pointy" wheel will help with control! Regardless, as always I throughly enjoy your video.

[@KAMiJUINs]

Thank you for your opinion and watching :-)

[@unitedxhatersdownhate4813]

will be awesome if you change for small wheels like a roller skate and electric. nice idea!! haven't see anyone trying to get a roller skate electric .

[@KAMiJUINs]

Thank you for your opinion and watching :-)

[@SFoX]

They give me Jet set Radio/Bomb rush cyberpunk vibes. I love it

[@KAMiJUINs]

Thank you for watching :-)

[@Bogunes1337]

Im imagining falling with this, crazy

[@KAMiJUINs]

Yeah, it's gonna hurt a bit

[@Charles-Darwin]

gotta put either the batteries or both the batteries and esc/controls into a small backpack and run wires down to the skates somehow. since your foot is locked in anyway. then they could be lighter and made smaller overall lol that amount of weight on each foot is crazy

[@KAMiJUINs]

I feel the same way about the weight, but I didn't like riding with wires. That's why I got this design. Thanks for the suggestion and watching :-)

[@EinarOfBC]

Those snowboard bindings are likely to break your ankle one of these days wearing skate shoes like that. They are designed to work in conjunction with a very stiff boot that takes on the role of supporting your ankle. Also, the longboard wheels are stopping you from being able to turn. Flat wheels like that need some kind of steering rack (ie a skateboard truck). Good prototype, but you still have some major safety flaws.

[@KAMiJUINs]

I agree with you in terms of stable ankle support. Thanks for the suggestion and watching

[@appslagu4704]

man this makes me remember the Rollerblade anime.. Air Gear.. for those who not familiar with this anime ..you can search it on youtube ..

[@KAMiJUINs]

I see :)

[@ravistech3757]

Interesting Project!!

[@KAMiJUINs]

Thank you for watching :-)

[@28호-t1b]

정강이까지 잡아주면 더 안정적이지 않을까요?

[@KAMiJUINs]

그부분에서는 확실히 더 안정적일것 같습니다. 운동화를 스노우보드 바인딩에 고정시키니 발목부터 불안하긴했습니다.

[@styxicrix2587]

I missed you buddy good job on ur skates! Go watch air gear :) for inspiration ❤

[@KAMiJUINs]

HaHa, Thank you for watching bro :-)

[@MadDonJuan]

Crazy build haha, those swollen lipos gaved me stomach pain. 😂😂 Did the skates turned like regular ones do?

[@KAMiJUINs]

HaHa bro :-) As I said in the video, the skates themselves were heavy, so I didn't even care about turns. lol Thank you as always!

[@guitarwi3rdo]

Yeah, strapping 10lbs to each foot will take some getting used to. Really clever build overall

[@KAMiJUINs]

Yeah, It was!!! Thank you for watching :)

[@vms988]

Nice work!👏👏

[@KAMiJUINs]

Thank you for watching :)

[@auden_builds]

amazing work!

[@KAMiJUINs]

Thank you for watching :)

[@JIMPARTS]

Nice build 👍interesting how it with less square wheels 😉

[@KAMiJUINs]

Thank you for watching :-)

[@jashall30]

Thia is strat from an anime i love it

[@KAMiJUINs]

Thank you :)

[@pablotope3070]

Man excellent job Kami! I would pay for.your servixes any day to help me on my esk8 remote- motors still wont turm and not sure about vesc tool innwhat to my do- atill way new at esk8. It is an mbaord interstellar 2.0 with the flipsky vx4 remote.

[@KAMiJUINs]

Thank :) Then, how about contacting M Board?

[@leelee2181]

오...뭔가 일본 만화 '에어기어' 에서 나오는 전동 롤러스케이트 같네요 ㅋㅋㅋ

[@Kiwikeds]

Best

[@grasiciel]

Kami as always nice design 😎😁

[@KAMiJUINs]

Thank you so much :) for a long time.

[@KoreaFlyingSquirrel]

와 한국인이셨구나 ㄷㄷ 바인딩 결합만 더 손봤어도 탈만했겠난데요

[@KAMiJUINs]

네~, 바인딩도 바인딩인데 무게가 너무 무거웠습니다

[@쭈니-t8n]

갖고 싶네요 와 출퇴근 할때 좋을듯

[@KAMiJUINs]

그러기엔 조금 무거울것 같아요 ㅜㅜ

[@MrPafleouf]

large flat wheels are also not helping with turning / cornering... maybe try finding some rounded ones

[@KAMiJUINs]

Thank you for your opinion and watching :)

[@esk8jaimes]

Could you try these with a more concaved contact patch wheels, like Cloudwheels for more carving ability?

[@KAMiJUINs]

Well... I'm going to try again if I have a chance.

[@Michaelajacksonfilms]

Meepos cyclone wheel will give more control and comfort. Or any wheel with a cambered / rounded profile

[@KAMiJUINs]

The wheels I used were not uncomfortable either. However, the skate itself was too heavy. lol Thank you for your opinion and watching :-)

[@esk8jaimes]

Any plans to transfer the electronics to backpack bag, like Atmos Gear have done with their electric inline skates?

[@KAMiJUINs]

Personal opinion, I think E-skates in that way is half finished. That's why I planned this build.

[@yoshuavillar]

First thing that went to mind was airgear SKY REGALIA~!

[@KAMiJUINs]

HaHa :-) Thank you for watching

[@yoshuavillar]

@@KAMiJUINs awesome build! Looking forward to the next one

[@scottyW]

Wow! Amazing! You must have went to MIT

[@KAMiJUINs]

NOOOOOOOO WAYYYYYY lol :-) Thank you for watching

[@Jess-nl8vt]

I would really like your opinion on the escend rollerblades in comparison to airtrick!

[@KAMiJUINs]

If I have a chance to review it, I will definitely compare it :)

[@Pukcholabiseriesh]

70% Done 🙏😄😄

[@易水-w8s]

product level

[@denischam3252]

Gréât AirTreck

[@KAMiJUINs]

Thanks :-)

[@yohvh]

How did you build and design the base that's insane.

[@KAMiJUINs]

I always do sketches when I think of something. And I spend a lot of time looking for materials that can make them happen.

[@SkyDaync]

Осталось изобрести электроконьки))

[@SuperMarijus]

pneumatic wheels would probably be best for this , more control less vibration and i feel like theyd be even more stable

[@KAMiJUINs]

Thanks for watching and commenting :)

[@Sanryuji]

When I saw this I remembered an old anime, Air Gear

[@KAMiJUINs]

HAHA many people said taht Thank you for watching :)

[@krishnansrinivasan830]

Awesome Sir :)

[@KAMiJUINs]

Thanks!

[@alexey8402]

ASMR👍👍👍

[@KAMiJUINs]

Thanks for listening :)

[@Humble_Balaclava]

Now make a Tracked version of this.

[@Yuriel1981]

When can i order a set? Lol bro you better patent these designs!

[@KAMiJUINs]

Thank you for saying that :) And I think it's impossible lol

[@pray4skylark]

만화에서만 보던 그 스케이트를 보다니

[@josedelmontealmansa6259]

ultra genial ami me encantaría hacerlos pero con orugas y motores de hoverboard.

[@KAMiJUINs]

Espero que puedas hacerlo como planeado :-)

[@esk8jaimes]

What's the hill climb ability like on these? Most E-skates struggle on hills...

[@KAMiJUINs]

As you can see from the SPAC, of course, it is more powerful than most E-skates. I just lack my skating skills lol :)

[@율환박]

제미있 겠다

[@taylorprimack4140]

You'd get more range and road absorption with inline skate wheels.

[@KAMiJUINs]

Thank you for your opinion and watching :)

[@AidenIsElite]

I feel that you should swap these wheels for some inline skate wheels. even maybe some aggressive ones. Id personally go for 90mm or above though. id bet those would feel a lot more comfortable.

[@KAMiJUINs]

Thank you for your opinion and watching :-)

[@yuvalsharabi9985]

brilliant!

[@KAMiJUINs]

Thank you for watching :)

[@cringeman6438]

Finally i can become the sky king

[@KAMiJUINs]

HaHa :) Thank you for watching!

[@user-uc9un5zv7h]

Lebih baik baterai dan controler taruh di tas biar lebih ringkas

[@KAMiJUINs]

Saya pikir itu tidak sempurna, jadi saya memilih desain ini.