Hi, @Garage build, I swap a jz on my Z... I know the cooling issues in this swaps, so I do the rear radiator swap in an20 hose. I don't cut the rear floor panel, just use 69' Mustang rad in stock catback room, dual fans & the expantion tank that you use... in adition I use the stock water pump and a secundary electric Meziere water pump in rear, runs good with absolutely no overheat issues.
@StreetFabPerformance4 жыл бұрын
That sounds cool. Maybe i do something like that in the future. I just installed bigger fans and it worked out.
@omhounde22892 жыл бұрын
Look at the RJM clutch pedal!! They are much smoother than the stock 350z clutch pedal
@cre8tivegarage1574 жыл бұрын
This set up is so fire 🔥
@SasquatchN644 жыл бұрын
Run 25% anitfreeze to 75% water. Look up the ratio chart. Water cools way better than antifreeze. Maybe get intake from turbo inlet to front bumper may also help a little with temps. And wrapping the down pipe etc sounds smart. Anyway to get the upper radiator hose straightened out?
@StreetFabPerformance4 жыл бұрын
Thank you for the tips. I will check out that chart. Yes I will for sure fix the hose I need to move radiator fwd about one inch or so that way I can make nice straight line.
@SasquatchN644 жыл бұрын
@@StreetFabPerformance also the best radiator flush you can do is add Cascade dish soap to coolant run it for 30 minutes then flush with water it will clean all your coolant ports. Cheap easy maintanence. Learned it in college for diesel technology/mechanics.
@kingbey84054 жыл бұрын
Sweet build..but the reason its running hot is because the fans has to be on the engine side..the car needs the wind from driving, while cooling off both ends, inside. 🤣 you remind me of myself with my ss trailblazer build😅. I hope I can get my g35 like this..
@StreetFabPerformance4 жыл бұрын
I fixed it a good now.
@ryanboyce79473 жыл бұрын
U need a restrictor for that ball bearing turbo
@ls6king3164 жыл бұрын
I'm going to do a RB26 Q50 build keep it Nissan with an automatic transmission
@Midz350i3 жыл бұрын
Mishimoto fans suck and I threw them in the trash. I have 2 14'' Spal 1800CFM fans in my built 2jz Z. They were coming too early and temp never got above 65C. Now wired them like OEM 1 fan with AC and at 87 and second fan at 93C. I had to fabricate a custom Radiator support for the extra space.
@thomastran24324 жыл бұрын
How much did your swap cost? Which Collins kit you get or needed? Just the mounts. Trans mount. Adapter and flywheel kit? Planning to do this for my 2003 350z as well. Just wanna get a general idea of it all and pricing. Thanks !
@StreetFabPerformance4 жыл бұрын
I got the one with everything in it. All mounts, flywheel, clutch, shifter. It was like 2200 buck for the kit. The swap price all depends on you. ran about 15 to 17.
@Ed-wr3wv4 жыл бұрын
@@StreetFabPerformance The swap cost you 15K to 17K? Just the swap itself?
@StreetFabPerformance4 жыл бұрын
@@Ed-wr3wv 20k
@rickqueen654 жыл бұрын
Bro, what is your intake setup? What DBW? Are you running your factor gas pedal?
@StreetFabPerformance4 жыл бұрын
I'm running 350z throttle body. No cable. Drive by wire.
@rickqueen654 жыл бұрын
@@StreetFabPerformance the 75mm or factory? How did you get it mounted up?
@StreetFabPerformance4 жыл бұрын
Factory. I had 2 flanges CNC cut. One for the intake manifold side and one for the throttle body side. Attached with cast aluminum 90 deg elbow
@rickqueen654 жыл бұрын
Nice work. Can you shoot me the diagram for that?
@chrisvaladez99404 жыл бұрын
What fuel return kit are you using?
@StreetFabPerformance4 жыл бұрын
I made my own kit
@ladin4254 жыл бұрын
Would you be able to tell me how much clearance you have between the back of the engine an firewall?
@StreetFabPerformance4 жыл бұрын
2" 1/4
@ladin4254 жыл бұрын
@@StreetFabPerformance Thank you, Sir! Would you have any idea if the stock twins would fit. I wouldn't mind clearancing some of the sheet metal. Genius idea integrating the throttle body, BTW!
@StreetFabPerformance4 жыл бұрын
I'm not sure if they will. I did not try it personally.
@Cressfromhell3 жыл бұрын
@@ladin425 not a good idea. It will be like working on a TT 300zx
@ladin4253 жыл бұрын
@@Cressfromhell the vg30 is a v6
@GuyX20133 жыл бұрын
Why does he have a ton of nissan stuff but no toyota? 🤔
@MatTheDragon4 жыл бұрын
How about the oil cooler what type did you add to the car ?
@StreetFabPerformance4 жыл бұрын
I have mishimoto. I have new video that will be posted tomorrow with all new parts. Stay tuned
@MatTheDragon4 жыл бұрын
👍👍
@Rambodontdoit4 жыл бұрын
How much would you say a 2jz 350z is worth with 100k on the body 65k on the 2j 700whp ? Looking at buying one just want input on what these go for
@StreetFabPerformance4 жыл бұрын
What is all do to the 350z? What is done to the motor? Trying to get idea of upgrades.
@Rambodontdoit4 жыл бұрын
Garage build stock 2jz vvti precision 6466 cd009 built and nismo rear diff
@StreetFabPerformance4 жыл бұрын
@@Rambodontdoit 20
@bo.rashed4 жыл бұрын
Did the AC works?
@StreetFabPerformance4 жыл бұрын
Its installed and wired. I need to adapt my ac compressor lines and service it.
@bo.rashed4 жыл бұрын
Garage build sound good brother.. thanks .. i have z33 2006 with 2jz but main problem the ac compressor position im use the car only in wintertime