He was very patient and detailed in the video. I agree the caulking could have done better.. but overall he is better than other plumbers.. he will get my job
@PlumbingRight4 ай бұрын
Thanks! I appreciate that. I agree the caulking wasn’t the best
@steveperry42454 ай бұрын
Easy stuff. Been plumbing for over 40 yrs.
@peterramkahlawan52354 ай бұрын
Why you calling the man stupid.. he is far better than others.. he got the job done and explained what is he doing..
@PlumbingRight4 ай бұрын
Thanks so much!
@user-wx9tl8mx6e3 ай бұрын
Everybody complan but for me You die a exelente job, thanks for the video
@PlumbingRight3 ай бұрын
Thanks! I appreciate that
@mauricioguandique95754 ай бұрын
ME GUSTO BUEN TRABAJO...GRACIAS ES BUENO APRENDER.
@PlumbingRight4 ай бұрын
Thanks! I’m glad you enjoyed the video
@williamkane69514 ай бұрын
The set coming out was installed upside down (thus the loops in the tubing). The new o n e could have been installed right side up just as easily.
@user-mn9gj9op1n4 ай бұрын
Sweat, press and MPT all on that diverter Swell !!!!!!
@Goodoletom9164 ай бұрын
I installed that same valve a few days ago, I liked it, I thought they couldn’t have nothing but the generic Chinese valves because of the anti scald valve law, I picked it up at Lowe’s, I wasn’t expecting it to be a Moen
@PlumbingRight4 ай бұрын
That’s awesome. It’s a good valve and eazy to work on.
@user-zi2pd8dd8w4 ай бұрын
I’ll replace my own I learned enough of what NOT to do from this video!🤔🙄
@PlumbingRight4 ай бұрын
What exactly would you do differently? Sharkbits? Everyone is a Plumbing god apparently on KZbin 🤣🤣
@markhanson3981Ай бұрын
This guy sure loves those channel locks, too bad he don't know how to use them
@PlumbingRightАй бұрын
How would I use them correctly?
@andrewwelch56685 ай бұрын
That old 3 handle Price Pfister tub faucet you took out could've probably been rebuilt with new stems and seats. Still rebuild quite a few of them to this day and never had a problem doing it. Might have even been able to salvage the trim if you didn't go full caveman on the hot handle. Moen is a fairly good brand to replace it with, but you made it sound like you were taking out a 3 handle Moen faucet in your video headline.
@davidmcmullen37804 ай бұрын
I could have rebuilt that old faucet. Used a handle puller to get the handle off. Kingston Brass has the same exact faucet to replace with or just rob the stems handles sleeves and escutcheons and install them and leave the old faucet rough in valve intact.
@rudybisonaya30254 ай бұрын
Q
@rudybisonaya30254 ай бұрын
Q
@RossDAwgOfficial4 ай бұрын
Rebuilding is for the handyman, not for professional plumbers, most of us plumbers would offer a zero day warranty on rebuilding
@PlumbingRight4 ай бұрын
I agree! ☝️
@user-hz1rf1gk3t4 ай бұрын
Посмотрел, и убедился "руки с одного места растут"
@3630FS4 ай бұрын
Ok, job for DIY, try not banging the fittings on, should slide on smoothly! You really should make sure it's level! It's leaning forward !You might want to clean the surface from existing caulk and then reply. Otherwise, if the customer is happy so be it ..
@madelaine38034 ай бұрын
Why not use 44d to loosen it
@jfa31Ай бұрын
А зачем три крана, что за агрегат такой?
@awongutumeАй бұрын
Wouldn’t the seals in the manifold be damaged from the heat of that torch? Suggest a wet towel be placed to lessen the impact. Or, better yet, solder first with the fittings removed.
@PlumbingRightАй бұрын
Not necessarily. I don’t put that much heat on the fittings.
@jayyoo9064 ай бұрын
Taping has to seal pipe end too. The fringe is another seal.
@americoorellana12914 ай бұрын
No tiene la menor idea de nada. Solo tenía que cambiar la valvula de la llave de transferencia. No tiene necesidad de cambiar toda la griferia. Que haga un curso de plomeria urgente.
@stevejurasinski8434 ай бұрын
My second time working on stems yes I didn’t pack that handle out. When I threaded it back in the stand was too far and it broke the back of the valve. I know all about that stuff. Customer wants to pay you for a brand new valve should’ve put in a single handle valve and a much more better looking dumb but that’s just me.
@PlumbingRight4 ай бұрын
They didn’t want a single handle valve. They didn’t like how the plate looks.
@cafemolido54594 ай бұрын
Would you also repair the back wall?
@PlumbingRight4 ай бұрын
The wall was already opened up when I got there
@edwardcartwright86584 ай бұрын
Why take out the Price Pfister value when you can just go with the same value ? In my opinion the value that was there is better then the one being instill now
@user-kw7ge1lm9k4 ай бұрын
😊😮
@PlumbingRight4 ай бұрын
I disagree.
@user-te5nk8sc9z4 ай бұрын
Moen makes this stem valves? Not price phister company's?
@PlumbingRight4 ай бұрын
I installed a Moen. Phister was the one I took out
@happytiger810 ай бұрын
Looks really nice. Great job 🎉
@PlumbingRight10 ай бұрын
Thanks!! I know it was a long video 😂
@happytiger810 ай бұрын
@@PlumbingRight you’re welcome. It is 😳lol! It’s okay 👍 played it until the end 😅Keep up the good work 🥳
@PlumbingRight10 ай бұрын
@@happytiger8 That’s awesome! 🍿😁 Thanks for watching and the support! Will do
@happytiger810 ай бұрын
@@PlumbingRight 👏you’re welcome. Yeah 🍿🥤lol. Have a good one.
@charlescoates576110 ай бұрын
👍👏 You Need a Handle Puller 🙂
@PlumbingRight10 ай бұрын
I thought about that today 😂
@kelm11235 ай бұрын
I have a Gerber three handle shower and can't wait to do this. Great job man
@PlumbingRight4 ай бұрын
@@kelm1123 Thanks so much for watching!
@stevejurasinski8434 ай бұрын
7: am. Dude needs to buy a Pasco handle puller to reuse handles… and yes just replace seats-gaskets, and diverted washer.. doo - doo
@PlumbingRight4 ай бұрын
Not if the customer wants a new valve. I guess you’ve never stripped a seat out. Why waste your time trying to fix something. That’s plumbing 101
@enriquealvarez3783 ай бұрын
Can a shower faucet be installed horizontally?
@PlumbingRight3 ай бұрын
Yes it can
@brunoblanchard77064 ай бұрын
Le travail de treue
@justomedel66334 ай бұрын
Le pega bien poca
@frankiesoto41392 ай бұрын
Everything was cool until he started putting the Culkin 😅. It would have been better if he placed it on his finger.
@PlumbingRight2 ай бұрын
I agree 😂 definitely not my best Caulking job
@JonathanScott-ft1ns6 ай бұрын
300 degree grease is not for o ring or gasket use. Read the label you threw away. They sell actual grease for o rings.
@PlumbingRight6 ай бұрын
Thanks for watching anyway
@user-ct3ih8qy5r4 ай бұрын
Este fontanero es un inexperto
@PlumbingRight4 ай бұрын
🤣🤣 How? No leaks✅ Happy Customer ✅ 🤷🏻♂️
@user-we2cj7yl4m4 ай бұрын
En ese diámetro de tubo no ay. Que calentar el tubo. Basta con que se caliente bien la pieza
@user-es9ih6xi7g4 ай бұрын
Why don't you use a handle puller
@PlumbingRight4 ай бұрын
So you probably can’t tell in the video but the screw was just stripped out. A handle puller wouldn’t work.
@alvarogonzalez4524Ай бұрын
Cómo se te ocurre usar ese alicate para eso, aprende a utilizar cada herramienta, que bárbaro 😮
@ak07924 ай бұрын
Bro nice job but you need to work on your siliconing and your soldering. It was a bit rough
@PlumbingRight4 ай бұрын
Will do! Thanks for watching
@martinalarcon31082 ай бұрын
I noticed the tape measure he was using 😮😢was the one we called in our trade the dummy proof ruler 😮😢
@Frbid2lvme2 ай бұрын
Why does it matter what tape measure he uses? - I mean he got the job done and the customer is happy
@martinalarcon31082 ай бұрын
@@Frbid2lvme are u one of those that doesn’t know how read a tape measure? I learn in grammar school
@Frbid2lvme2 ай бұрын
@@martinalarcon3108 that’s cute!! I bet your parents were so proud that you got a gold star in reading a tape measure in grammar school - now you grew up and can pick on others for using a random tape measure - good for you sir!! Hope you have a great day!!
@martinalarcon31082 ай бұрын
@@Frbid2lvme I actually don’t use one , my eyes 👀 and sense are pretty good 👍🏻 I can guess pretty good 👍🏻
@lololauri46524 ай бұрын
Leave him alone,he did a good job 👍✅🎉
@PlumbingRight4 ай бұрын
Thanks! I appreciate that
@aussieboy18534 ай бұрын
I quit after watching the bonehead trying to remove the hot-side handle with Channel Locks! Yup... there's a simple tool for the job.
@PlumbingRight4 ай бұрын
Thanks for watching. It was all getting replaced so who cares how it comes out? Not me, Just get the job done. One day you’re not going to have the tool you need. I guess you’ll just give up and go home
@donking30204 ай бұрын
This is hilarious!! There is a simple puller for this job!!
@PlumbingRight4 ай бұрын
@@donking3020 Okay 👍🏻
@patrice89254 ай бұрын
You dont need mip adapters pipe will slide into valve
@PlumbingRight4 ай бұрын
I’m fully aware. Did you watch the video?
@BOBBY-et9xb4 ай бұрын
What is the center tap for.
@PlumbingRight4 ай бұрын
It’s for the shower head
@BOBBY-et9xb4 ай бұрын
@PlumbingRight I thought so but wasn't sure. Very Neat. 👌 Haven't seen a system like this in South Africa.
@PlumbingRight4 ай бұрын
@@BOBBY-et9xb Thanks for watching!
@enriquetrejo31214 ай бұрын
A ch1nga la Fria es una llave la Caliente la otra y ¿ la de enmedio que es Tibia?
@PlumbingRight4 ай бұрын
The middle handle is for the water to go up to the showerhead
@SergioFlores-of1lv4 ай бұрын
El de enmedio es para la regadera de arriba, para cuando vayas a la ciudad ya sepas para k es 😂
@user-we2cj7yl4m4 ай бұрын
Ese tipo dónde aprendió plomería
@humer1014 ай бұрын
Good job, however this set up is illegal in my State since 1999.
@PlumbingRight4 ай бұрын
Thanks! What state are you in? I would have put a single handle valve in but they didn’t want that big repair cover.
@humer1014 ай бұрын
@@PlumbingRight NJ
@PlumbingRight4 ай бұрын
@@humer101 Nice! I’m in Va
@UncleHo54 ай бұрын
May I ask you why is illegal? In Europe we don't use this thing, one lever is enough.
@humer1014 ай бұрын
@@UncleHo5 It Is illegal because you do not have an anti-scalding device or a mixing valve to regulate the temperature before you enter the shower or tub.
@allenzackery16394 ай бұрын
If there was any rubber seal inside the valve it probably got cooked....
@PlumbingRight4 ай бұрын
I don’t put that much heater in it. It’s fine
@user-tm5dt6xr6e4 ай бұрын
Вино Коньяк и Пиво 👍😂
@user-sv9st3xv1m4 ай бұрын
Get a better torch man .
@PlumbingRight4 ай бұрын
Thanks!
@justomedel66334 ай бұрын
Po nele una gomaa l a la llave para que no se resbale le pegay bien poco
@edwardcartwright86584 ай бұрын
You handle remover tool
@soriniacobescu10974 ай бұрын
Tu fais quoi Dorele?😂
@josephjabbour85494 ай бұрын
The sloppiest piece of plumbing I have ever seen.
@user-nt8sg5pt3j4 ай бұрын
This guy don't know why he's doing You're supposed to have a pulley for those handles so that way you won't ruin the way he's doing Don't follow that it's not the right way to do pull those handles out
@PlumbingRight4 ай бұрын
If you’re keeping the handles yes, If you know the whole valve is getting replaced, who cares how it comes off?
@Hamdala4444 ай бұрын
😂😅😂😂Esta apretad solo
@williamrsmithjr10024 ай бұрын
If you would have loosened the trim and used that to push the handle off, I have done this dozens of times. It would have saved a handle in the process. No sense being a barbarian and destroying things.
@PlumbingRight4 ай бұрын
Thanks, I’ll try that next time. The whole valve was getting replaced anyway
@user-jw1wl9kr3o2 ай бұрын
It was ok l give you an 8 .😊
@PlumbingRight2 ай бұрын
Thanks! I appreciate that 😁 Thanks for watching.
@user-we2cj7yl4m4 ай бұрын
Eso se solda afuera. Y despues se enrroca.
@jorgeluke62354 ай бұрын
I believe that's a Gerber 3 handle showerbody not moen
@PlumbingRight4 ай бұрын
It’s a Moen 2995EP Chateau
@jorgeluke62354 ай бұрын
Okay
@user-bf2hd9bu1r4 ай бұрын
Not a plumber
@PlumbingRight4 ай бұрын
Really? Where is your Plumbing work so I can pick it apart? Definitely not on KZbin.
@JoseAlvarez-cx7oz4 ай бұрын
QUE ALGUIEN LE DIGA A ESE " PLOMERO."............ QUE EXISRE UN EXTRACTOR, CUANDO SE HACE DIFICIL LA EXTRACCION DEL HANDLE.
@michaelpunty68734 ай бұрын
Buy a puller if you’re going to do this kind of work, have right tools so you don’t look like a moron. ….or, another option is to hire a competent plumber. 🤨😏🤭🤷♂️
@PlumbingRight4 ай бұрын
I did after this video. I have 645 videos on this channel and my whole 19 years of plumbing is based on one video 😂
@fahdgabasha7503 ай бұрын
next time change the blck rubber washer .. its going to cost a $2.00 and replace the handle the one you brock .. witch doesn't come out EZ
@PlumbingRight3 ай бұрын
The customer wanted a new tub/shower valve. Not everything wants things fixed, especially we’re I live
@andreadidomenico507910 күн бұрын
Ma non penso tu sia idraulico troppi casini
@PlumbingRight4 ай бұрын
What’s really funny to me is all these people on here saying I’m not a Plumber, when they don’t even make time to make a channel,put in the work, post it so the world can pick it apart 😂 I want everyone to make a channel in 2024 and show their skills!
@theeaskey4 ай бұрын
Most of those complainers on here don't know how to tie their boot laces. So don't heed them , the end result was it got fixed..
@PlumbingRight4 ай бұрын
Thanks! That’s true and the customer is happy
@patrice89254 ай бұрын
You got to be jiving.
@tomasestrada47524 ай бұрын
PLUMBER RIGHT ?? NEXT TIME , PUT SOME WD 40 , BEFORE YOU START DOING ANY WORK.
@martinantoniolazarte33514 ай бұрын
Es una estafa el video no mostro como ejecuto la soldadura ascendente ..De Argentina..
@jovansegovia79174 ай бұрын
😅
@fuzzydon8574 ай бұрын
Next time you going to make a video least use the correct tools.
@user-yr5iq2st7k2 ай бұрын
Quitale el tornillo de enfrente
@williamrsmithjr10024 ай бұрын
Stick to the drumming because you ain't got plumbing down yet!
@user-vz8jc1rz6m4 ай бұрын
This guy has NO Clue
@PlumbingRight4 ай бұрын
🤣🤣 Okay
@ignaziopibiri23423 ай бұрын
Agricoltura mancata
@fredymendez17864 ай бұрын
You need to improve how to put the silicone.
@hernandezm.karaoke57034 ай бұрын
Amigo de plomería nada, esa no es forma de sacar manigueta de llaves, para eso hay extractor, la has rayado toda, 😢
@PlumbingRight4 ай бұрын
The tub valve was being replaced anyway
@jamshidetemadi84904 ай бұрын
😂
@americoorellana12914 ай бұрын
Como plomero sos un excelente zapatero. La silicona se pone entre la pared y la griferia, no afuera de la campana. Cambiaste una griferia al dope, solo tenias que cambiar la valvula de la llave de transferencia. Un asco como trabajas, hacete un cursito de plomero, son gratuitos.
@PlumbingRight4 ай бұрын
I’ve been Plumbing 20 years, Went to a 4 years school and have a Masters license. Thanks for watching anyway
@santiygo3835 ай бұрын
Так себе мастер похрду😂
@miguelantoniogonzalez53504 ай бұрын
Esta persona no sabe trabajar esa muletiya se quita dando unos golpezitos en la misma es una pena ver esto😮😮😮😮
@williamrsmithjr10024 ай бұрын
This guy is not a good maintenance person. Probably dropped the fixture because I have never in 30 years saw a fixture with bent orifices like that. Unless it was abused in some way, and judging from the way he disassembled the existing one is probably how the new one got damaged!
@PlumbingRight4 ай бұрын
I have 600+ videos go watch some of them
@user-rj4qz4ug8k4 ай бұрын
One job so long
@PlumbingRight4 ай бұрын
How long is it supposed to take 10 minutes?
@user-rj4qz4ug8k4 ай бұрын
@PlumbingRight I think if we put our minds on one job at ah time it would be very quicker
@chistesconelgonzagonzagonz60372 ай бұрын
Está muy pendejo para hacer plomeria, tuvo que poner 2 tees para las ventilas para que no agarre aire la tubería, cambiarla igual está muy fácil pero si van a hacer un trabajo deben de hacer un trabajo bien con sus ventilas
@PlumbingRight2 ай бұрын
What tees are you talking about?
@josecamacho57554 ай бұрын
35:40 no sabe ni pegar el club
@user-we2cj7yl4m4 ай бұрын
No tiene golpes de agua
@FrogsArmyMom4 ай бұрын
What is water shocks?
@seanhawkins94094 ай бұрын
O
@williamholmes52974 ай бұрын
Not a moen
@PlumbingRight4 ай бұрын
The new one is a Moen
@abdelmoumenvideaste22184 ай бұрын
آش هاذ التكليخة، هرس الروبيني وبارك تايفورسي عليه، راه مازال شادو الڤيس، خدمة ماشي بروفيسيونيل 👎👎👎
@jesti66914 ай бұрын
Man macht viel verkehrt.
@PlumbingRight4 ай бұрын
Probably, but the customer is happy so who cares
@rubenlascanosanchez64874 ай бұрын
Le falta mucha técnica es muy pobre su forma de trabajar
@cardenasfamily78164 ай бұрын
No no no es cierto todo buen
@orlandogomes86624 ай бұрын
Este plomero es un fraude
@PlumbingRight4 ай бұрын
Explain?
@williamrsmithjr10024 ай бұрын
I would never hire this guy to do any plumbing in my house. He is not good at what he does. Well maybe demo!
@montamang8373 ай бұрын
So old design
@PlumbingRight3 ай бұрын
Okay
@user-jw6zl9tz9l4 ай бұрын
С таким дерьмом я ещё не сталкивался!😂
@cardenasfamily78164 ай бұрын
No SEAS OFIOSO
@user-cl8ji8fh7r4 ай бұрын
Es un aprendiz no sabe nada
@PlumbingRight4 ай бұрын
I’ve been Plumbing 20 years, 4 years of schooling and have a Masters license. Show me your skills. I’ll wait 😁
@user-rj4qz4ug8k4 ай бұрын
Put behind and tap off U r ah waist time plumber
@miosesjoseretamalrojas75383 ай бұрын
Descalificado fuera
@miosesjoseretamalrojas75383 ай бұрын
Te quedó horrible
@miosesjoseretamalrojas75383 ай бұрын
No sirve ni para cambiar piezas
@user-dt4mr7lb2e4 ай бұрын
Отсталая страна. Весь мир включая страны третьего мира давно перешел на однорукие смесители.
@user-ci6mw2wk8b4 ай бұрын
You are a terrible Plumber
@PlumbingRight4 ай бұрын
Why? Based off of one video on KZbin? I don’t see your channel on here. Maybe you’re scared 🤷🏻♂️
@heniekhenk11022 ай бұрын
Kto tam kładł płytki?😂😂😂😂
@heniekhenk11022 ай бұрын
Co za facet do wszystkiego używa żabki 😂 wali nią po międzianych kształtkach jak spawacz po szynie
@heniekhenk11022 ай бұрын
Silikon to tragedia nakładany szmatą co to za technika ?😂😂😂