tub and shower valve replaced in tile wall

[@myronsmith2114]

I liked the way you measured for the tub spout. In 30 years I never thought that way.I always measure the depth of the threads to the base of the spout

[@Capecodguy]

I cant tell you how many of these nightmares I used to do. I like watching these videos in bed at home better than doing them lol

[@SmokeScreensEmerge]

It's like studying a plumbing job while listening to "The Sopranos" in the background.

[@WAJSSJ]

So authentic he's managed to replicate James Gandolfini's heavy breathing.

[@Android_Warrior]

😆 😅 😂 🤣😆 😅 😂 🤣😆 😅 😂 🤣😆 😅 😂 🤣😆 😅 😂 🤣😆 😅 😂 🤣😆 😅 😂 🤣

[@wotlos3806]

I came for the plumbing, but stayed for the conversation.

[@codingmechanic8954]

lol

[@stevebronsted8268]

The homeowner talking is the best part! 😂

[@aromeromq]

Kregg Solto

[@woodgrainstudios7321]

me too...LOL

[@eddiew2325]

Kregg Soltow not really Greg you see I am a Viking Anna Nicole Smith

[@readmore3634]

I replace 2-3 tub/shower valves a month....and have never put channel locks on a brand new chrome filler/spout. Come On Man!

[@lilturk726]

Strap wrench man

[@mikhaielj]

It’s always very funny 😁 when a DYI dude try to correct someone that is been in the trade for 30 years Instead of saying thanks for sharing his knowledge for free There is so many ways of using Chanel locks that you don’t learn with out experience He did all that work straight out of the truck You probably also had run the hardware store 10 times to get your push fittings 🤣 Also there is teeth less Chanel locks Thanks Steve for sharing your knowledge with these unthankful. People

[@readmore3634]

@@mikhaielj....... My comment was addressed to Steve, not you mikhaielj ...just giving him a hard time...(joke) Maybe you didn't read my comment...."2-3 a month" and I'm not even a service plumber. I just do it for my client's friends and such. Hand me a set of plans and I'll plumb that Mansion from the ground up by myself. 40 yrs in the plumbers union...2 fully vested retirements. It's always funny 😁 when someone thinks they know me...don't pretend you do....and Steve could have just replaced the stem/cartridges/handles. But maybe the home owner wanted a more modern single handle valve. His locks had teeth...and that's fine...just don't teach it. Stay in your lane mikhaielj ...

[@mikhaielj]

I apologize

[@readmore3634]

@@mikhaielj Thx, accepted

[@asharma5958]

Never realized how dirty peoples houses are until i started watching you.

[@Android_Warrior]

😆 😅 😂 🤣😆 😅 😂 🤣😆 😅 😂 🤣😆 😅 😂 🤣

[@gyver471]

Steve I swear you make the most complicated jobs look easy there's definitely a lot of wisdom in that head of yours great job your teaching us young guys that could use all the help we can get👌🏼

[@freethebikes]

I genuinely love your videos and think you're a great film maker aside form the plumbing stuff. There is something cool about the candid moments you capture with the customers that feels like slice-of-life art.

[@jasonjoncas5998]

When in doubt cut it out. Tough job Steve looking at this 6 years later enjoy your vids to the point with the customers keep it up.

[@SeanBaker]

All these folks in the comments talking bout they'd knock out the homeowner or tell him to go away cuz he's talking so much. 🙄 You're gonna talk yourself out of business.😂 Better learn some good customer service like Steve.

[@RobHVAC]

I feel for you. I could not stand someone talking to me about all their issues. Nice job on the faucet.

[@stevenlavimoniere]

i kinda just tuned him out and did my job

[@mitchvankesteren6771]

I was waiting for “every oowaa you stand dar bulkshittin wit me is noindy Faiiive doooollas guy”

[@bg147]

They really built these old houses! My tub has the faucets and shower head on the side of the tub with easy access from the closet. This was a bear of a job with that wall you had to deal with. Nice work.

[@stevenlavimoniere]

bg147 i got her done

[@stevealaska73]

I use the handle of a hammer to tighten or loosen the tub faucet. Or the handle of a socket wrench in a pinch. Im surprised no gasket was used for the plate. My favorite part was when your torch was on and I could no longer hear that homeowner. haha

[@Allbbrz]

+stevealaska73 I was thinking the same: no gasket ??? That's recipe for mold growth behind that plate and inside...

[@mfielding007]

cant believe i have only just found your channel , great videos

[@jaimes1572]

Oh man thank you!!! I have this same issue and no plumber will fix it without doing a mistake plate so I’ve been working on it myself. F-ing nightmare. Thanks for the info

[@PRO4XKEV]

I learned something new again from Steve's videos.. Awesome job.

[@markb.1259]

Nice video Steven! No plumber's putty or caulk behind the renovation plate? Sure hope that large hole in the wall behind the plate doesn't collect too much water!

[@heyitsthatoneguy91]

Idk about those repair/smitty plates but some of the shower face plates come wth a soft sealant ring on the back just inside the lip.. You cant see it but it stops the water so you don't have to use a sealant

[@cuznboodro32]

I wondered how far down into the comments would I c this question. It doesn't look like it's waterproof

[@jsbenami]

The NYC/Boston style accented cussing & commenting is HILARIOUS!!!

[@stevenlavimoniere]

jsbenami i am glad you enjoyed it lol

[@jsbenami]

Thanks for sharing this stuff boss. It's helping allot. I'm watching your toilet flang vid. I'm doin' all this stuff tearing out my 40's bathroom. HAHA smoke alarm.

[@smedoz]

That ain’t no nyc accent

[@bronzesolomon4453]

I love hearing a couple of NY, NJ, PA Italians dialogue. You'll hear the word "fuck" 1000 times in one sentence😂😂

[@rawtry65]

It's like there is nothing you can't do...Great job.

[@tdbsnr]

Angle grinder?? A reciprocating saw with semi circular tile cutting / grout rake blade, cut along the grout lines & remove the tile, much easier & far less messy, tiles can be replaced easily afterwards. Also, cut into the plaster for easy removal. But nicely finished job.

[@mr.dahliaking.202]

I did the same thing :D "eh, fuck it" and there goes angle grinder :D 3:13 Good work Steve! I'm 16 and I just finished my work at my friend's house, I put in wall hung boiler, changed the old toilet (what a mess it was) and cleared the drain with the snake. I also redid the whole water supply system with new plastic pipes, I'm surprised that I was able to finish everything with only one leak after everything was done, I fixed the leak and my job after 5 hours was complete! I wish that in the future I will be as good plumber as you are! Keep up with good work!

[@stevenlavimoniere]

+Vytautas Poška sounds like your off to a good start

[@lenjames]

Goodness the original tile job is horrible. I get sad that someone installed tile like that. Great job Steve ...that ust of been one old home with all that plaster.

[@MLEB723]

Lots of videos of guys doing plumbing and then there are videos like this of Plumbers doing Plumbing. Great Job.

[@doylehargreaves5057]

I like the way it turned out. Very professional and clean looking. You have a great job. I would love to do what you do for a living.

[@septicman361]

Awesome job Steve. I like those symmons . They are not very popular here in Atlanta I don't know why.

[@stevenlavimoniere]

symmons is a good valve i work on a like of them

[@newmoon54]

Another nice video Steve!!! From one HVACR tech of 45 years to another,,, be safe, take good care of that chihuahua!!! They're smarter than us!!! I have ~5 Chichi's~ lol!!! My life is so much happier thanks to my ~Fabulous Five~! Chow Steve!!!!! Sal 🐈🐈‍⬛🐈🐈‍⬛🐈.

[@SleazyMouse]

i love those old bathrooms for some reason

[@franciscoflores2862]

good job Steve. you can purchase a moen tub and shower valve ( posi-temp) with retrofit plate instead of regular round plate. I wish you would answer some of the comments from plumbers wanna be.

[@deputydan2226]

That's a family of story tellers 😂

[@cichlid62]

Why make that huge hole when you had the back opened anyway? The screws for the smitty plate would've went through the existing holes then all you had to do is make a smaller hole for the new valve. Just sayiing

[@jonwhite2706]

agree 100% was no need for that hole

[@helenavan7584]

Looks ugly to me

[@doneown503]

Yup, and always check far side of wall for anyelectrical,, ,

[@bigglilwayne7050]

Or go back with another 2 handle since they outperform single handle valves anyways....

[@bigedd91]

@@bigglilwayne7050 not Mass plumbing code.

[@SovereignTroll]

Nice work on old tile with lathe. Master plumber. I am dying at the Sopranos reference below. I would be entertained.

[@bigrayray43]

LMFAO !! Good video, Steve. That homeowner sure needed someone to talk to. LMFAO Good plumbing tip though.

[@stevenlavimoniere]

yes guy was funny

[@kellerrobert80]

18:04 "I loved her to pieces. hahahahhahaha!"

[@tremayne3]

This is the best video on youtube !!!!! I can't get enough of it ,,,so entertaining...so candid...so natural...and its pure New England vibes !!!!!

[@stevenlavimoniere]

+Pete Mago thanks for the support

[@81recinos]

You are a true plumber sir I done something for the last 20 year good job

[@Indianaxes]

Great how to. Just what I needed to know. Just wish it was as easy as you make it look. Thanks

[@atenebruso]

That was a good one Steve! To bad there isn't a shut off valve for home owners mouths sometimes. Just did a job today with a chatty homeowner.

[@stevenlavimoniere]

homeowners talking don't really borther me to much i left it in because its real world stuff

[@RockinProfessor]

I simply shut the bathroom door while I work if someone insists in bothering me.....doesn't happen often but 'I don't like distractions

[@tomplumb74]

Nice job Steven, I used to use Simmons but switched to Delta for several reasons. Most of all service issues and costly parts. I can fix a leaking Delta and be out the door with a Simmons I've seen all shorts of nightmares!!!!!!

[@stevenlavimoniere]

simmons are very popular up my way ,,the old delta the 3 small tubs tent to twist off when removing some times if not removed properly

[@tomplumb74]

steven lavimoniere I also live in massachusetts, and I work on Simmons valves ten fold and I have many customers with Deltas and hardly ever need to service them. And it is very inexpensive to replace springs & washers on them. Opposed to a $45 spindle on Simmons , I know you can replace the washers on Simmons but it's a pain. I've had more than a few problems with Simmons where I couldn't explain why I could not fix a no hot water problem new ta-10, new seats, hot water in but no hot water out, as well as hard to service seats if not impossible on an old valve. My older customers really like the easy to shut off of a Delta! Grab one one day and see if you like them they are pretty inexpensive as well. Love you videos Keep them coming!

[@stevenlavimoniere]

tom plumb i have been meaning to do a video on simmons tub/shower valves there are a few tricks i have found that work for me

[@jasonsanitz5623]

great customer relations, should be a beer commercial. Looks like your repair may work though

[@stevenlavimoniere]

Jason Sanitz yes it worked fine

[@americanescu]

I love the east coast accents! LOL! Brings me home! Thanks for the vid! Learned a lot.

[@CSJiGSaW08]

12:12 - Wait what the fawk... You had access to the interior wall from the other side?? WOW, just WOW. No need to tear the tub wall when you can just replace the plumbing from the other side with a new 2 handle system. Now if they want a single valve, that is another story. Just WOW! You would of come out as a hero saving the tile wall if you gave the option. Plumbers these days man, just want to charge more and scam customers or defraud insurance...

[@av-lu3oi]

so true he couldve just work from the other wall and change the valves

[@buscandolaverdad6888]

He could just offer the same kind of valves and safe the tile, but many times plumbers wants to sell you what they already have in the truck and this is what happens 😆

[@registrocuevasondas2725]

I do plumbing but i always ask the customer give them what they want they are paying i do what they say never destroy the tile like thatif i need a quick repair i take control of the problem and after give them the choices

[@billw8742]

He's a plumber in Massachusetts. The valve he is installing is correct. By code up here you are not supposed to install the old two handle shower valves due to scalding. Hot water out of shower head must not exceed 112 degrees farenheit. Also a liability on Steve if someone gets scalded after he leaves, I would do the same thing. Keep up the good work Steve.

[@CSJiGSaW08]

BILL W You are correct but he could of plumbed the hot and cold water lines into the tile holes from behind with new male adapters and install modern style anti scald valves that run along the tile wall. These are the nice chrome modern rectangular valves where the valve is actually outside the wall and they grab the tile with clips/screws. The shower head pipe runs along a rectangular body to the top. These are one handle but you can utizilize the 2 holes already for the hot and cold. They are expensive but its up to the customers budget always.

[@Brad1237202]

Nice job Steven! You make it look easy!

[@stevenlavimoniere]

it is easy

[@texasdoug5739]

Really interesting...excellent job, Steve. Colorful customer!

[@richardabner9420]

I've been binge watching your videos!

[@emmantoast310]

Conversation was golden 👌

[@Keith1983_]

love your videos I'm an installs rough, some a/c not much finish and a lot of commercial guy but theres just so much service and experience can't be taught u have that clearly i think its using your brain but love your vids man thanks

[@stevenlavimoniere]

+100% percent thanks for watching

[@mitchvankesteren6771]

“Hey boss, how much mortar should I use behind this tile?” All of it son!

[@K9_Willett]

I like your videos. That's why I subscribed to your channel.

[@robertgaines-tulsa]

I don't know if he's caulking off camera. People are saying he doing a sloppy soldering job, but I wouldn't know since I've never done that. I don't why the customer is being a motormouth. I like how steven makes a comment about it just loud enough for the camera to hear. He may be enlarging the hole as big as he can so any future valve changes won't require any extra cutting. I would think that caulking under the plate would help keep water out better. As I said, I don't know if he's just not cutting off the camera before he does that or if he is just leaving it like that.

[@icap8830]

This fellow should hv been in Hollywood.

[@patrickgamache9935]

In Canada Symmons shower control are very expensive. I used Moen shower control. Moen are also easy to repair and less parts. Patrick from Neighbourhood Plumbing in Toronto Canada

[@guaporubio]

I didn't see how you changed out the mixing valve from the old two valve system. Did you just bypass that part of the job? That's the most important part of the whole project.

[@arneyjeff]

Wow three inch thick wall. I love her to pieces. Throw her in the wood chopper. Hilarious. Love the plumbing videos Steve. Can't wait for the next. Thanks Jeff

[@stevenlavimoniere]

i will try to bring more plumbing videos thanks for watching jeff

[@marvinlassegue951]

The parts design to block each, the cold water side one, the hot water side two, depending on the side you choose to turn on. Maybe when you open both faucets, both sides are unblock at the same time to bring down the warm water for the bath water. The shower switch located above the bath water knob turns the water into shower water which comes down from the shower head.

[@bryantylerservices]

That was badass Steve... Homeowner .ahhhh... Better go to work...😀😀😀😀🐾🐾🐾🐾🐾🐾🐾🐾

[@donker3163]

Your a nice guy. I would have told that guy to kick rocks I’m working. Guess you been doing it long enough to multi task

[@TheWolfePit]

Good work Steve!!!

[@stevenlavimoniere]

thanks larry you like plumbing work ??

[@TheWolfePit]

steven lavimoniere No I don't like plumbing work, but I find it a fascinating trade and a trade that will never go away!! Keep up the great work Steve!

[@LostLarz]

@@TheWolfePit Ohmg never thought I would see you here

[@KjbuckeyeHomeImprovements]

“Yea shot’em thru the bathroom door” as your working… in a bathroom 😂

[@pattirayne1243]

I was looking for a video for how to use a mistake plate to cover the hole you make in ceramic tile when you replace the old shower fixture but you had access via the rear. The thing in back of my shower is a shower! You probably couldn't have done all of this without access from behind right?

[@MegaRadio90]

ROL ... Steven!! That was some homeowner. Good grief that was like digging into Fort Knock's.

[@stevenlavimoniere]

the guy was ok just a little swearing going on

[@MegaRadio90]

ROL .... I actually gotta kick outa him !

[@Allbbrz]

I noticed no gasket; but boy, thanks. That gave me the pointers to what I have to do in my master bathroom....

[@stevenlavimoniere]

+Allbbrz good luck with it

[@WriterandPhotographer]

I just removed a square foot of tiles and will cut away the dry wall tomorrow, but it is an easier job that that thick concrete........looks like Fort Knox. Nice work; dirty tub.

[@csully561]

Best channel on KZbin 👍

[@waterheaterservices]

Those mistake plates are the greatest invention since pipe wrenches and Baby The Dogs

[@teamdrummond6915]

Steve, you're worth your weight in gold. Great repair job!!

[@fernandosalgado3589]

I got used to installing deltas I’ve done a lot of kholers too I like how those symmons look I hardly run across those. It’s like the homeowner would pay you just to talk to you

[@knowsenough2bdangerous]

At first I thought this job would all be done from the "tile" side and that it would be very interesting to watch working in that cramped space. But, nope, easy access on the back side (simple drywall on back side and (apparently) in a closet at that - no tile, paneling, or cabinet work).

[@lavatube8060]

@ 21:03...While he was soldering and it was super loud, the homeowner just kept talking and I bet Steve didn't hear a thing he said, haha!!

[@lavatube8060]

...homeowner has a point though. Be careful who you're marrying or just don't get married. they 'could' take you for all you have if they're vengeful types. If you have kids though, BOTH parents should always be obligated to support the kids financially, or don't have kids. I don't believe in alimony though. UNLESS the one spouse worked and put the other one through school, and then that person divorces them. that's not right, the person should pay the other back for their schooling. there are varying circumstances, but to get alimony just because you hate the person or are vindictive, is not right.

[@AJCOOL357]

Why didn’t you put some caulk around the plate?

[@ml3924]

TheBigBadGamer101 he was fed up with the owner lol

[@ufo69691]

cause he's a hack

[@luxurycarkey7207]

Great job...how much do you charge for a job like this...

[@dunnplumbingllc2779]

Grinders are such wonderful tools

[@stevenlavimoniere]

Dunn Plumbing llc i agree love the grinder

[@tim8166]

Thank you for your video sir! I want to do this to my bath, and your video will be a great help.

[@josesantiago764]

I want to know how you got the last few turns on that spout

[@kbeau10960]

GREAT JOB STEVE

[@honestplumbingnorthidaho]

Caught you with your hat backwards in the reflection of that Smitty Plate! Not a bad look for you LOL. Good work.

[@stevenlavimoniere]

thanks tim for watching

[@jimrodriguez4368]

Awesome video! I laughed so hard when you said loved her to pieces and throw her in the wood chipper! Great video Steven I have NEVER seen that done before and wow you work so fast!!!

[@stevenlavimoniere]

thanks jim

[@mahmoodnowroozi5162]

hi Steve first of all great job. we have the same problem that the hole is not big enough to replace that faucet. can you please tell me how i can get that metal plate that covers the hole, and what it is called? thanks

[@kingokafor6215]

Order on Amazon made by Westbrass

[@binthrdonthat]

OMG, LMAO------he didn't even stop talking while the guy had the torch going

[@dcrickerson9775]

Really interesting video, great job..The home owner was so funny.Thanks for sharing Steve.

[@stevenlavimoniere]

he was swearing alot

[@rickyonovitz3214]

Love the work and love the conversation....

[@OscarLopez-kh5kr]

Freakin' Fantasic Steve! I do have a question though... How tight did you screw that spout in? I have the same problem right now and I am afraid of cracking the tile or ruining something on the inside. Thoughts?

[@Vincerama]

I wonder if plumber training involves having to work while making small talk with talkative homeowners. LOL, even with the torch blasting the guy's still yapping.

[@winkhvac62]

Great video steven really enjoy learning from your Videos. Keep them coming

[@stevenlavimoniere]

thanks for watching

[@robotcowhand1276]

Absolute KZbin gem. Amazing video. Shortcut for repeat visitors.... 15:55

[@SkyChaserCom]

Haha!!!! I love the sailors talk of that guy (customer)!

[@doneown503]

15:12 - not only do you need a bunch of speciality tools, you need the fittings collection also!

[@genekhomenko2472]

Why you do not use any sealant under the plate?

[@gailfeddern7798]

Thank you for this video. It's exactly what my plumber needs to do. I like the plate cover you used much better than what my plumber wanted to use, because this one is a better match for my contemporary decor, yet it is neutral enough for any style. Also, this one is easier to cut because it doesn't have curves. Where can I get that cover plate?

[@GorgonnogroG]

just observing but do you not put silicone around the plate so the water doesnt seep behind it and go behind the wall

[@gyver471]

Best part was “she was probably giving him a hard time” that’s when you knew it was going to get good.

[@maalij-nelson9891]

Wish he had shown and told how and why he cut off the original pipes and what he attached the plate to.

[@wbl5649]

I need to have this done I guess. I've hit the old system and every couple years I have to have thecwashers replaced because the faucet will start dropping. And they charge me a lot just to replace the washers ! I use a root rooter type place to do that. If I get an updated system will it be washer less? And should i call a regular plumbing company or just have the rooter place do it ?

[@rocketrider1405]

With the wall being so thick, how did you correctly set the depth of the shower valve?

[@MrTtillub]

The tile man was a real master , LOL ……….

[@michaeltang50]

You are the expert. Thank you for your video.very interesting.

[@cchurch816]

All the new battery power tools and vacuums and dust collectors, still do it this way?

[@K9_Willett]

Does the tub spout (without the diverter level), turn completely turn off when the shower is fully activated?

[@papato3]

Older house, wet wall for tiles. Always thick before cement board.

[@stevenlavimoniere]

+papato3 this was like 3" thick

[@papato3]

Wow extra thick! Sounds like the apprentice messed up the mix and they had to do a second layer over it. Good video by the way Steve! Thanks for making it.

[@RockinProfessor]

Steve---why did you use those channel locks in tightening the tub spout ? You had to have scratched or worse the new spout's chrome finish & maybe indented the metal. Just sayin'; there is a better method I use.....

[@needmorediesel]

Good job steve, one thick ass wall for sure, them tiles will never fall off. How do those symmons valves compare to the moen posi-temp?

[@stevenlavimoniere]

needmorediesel i like both ,but symmons would be my first choise

[@cogless]

needmorediesel