3D boxes to your dimensions v 2 0

[@MrDmitryL]

Величезна подяка! Вже користувався сервісом. Фантастика! ❤👍

[@TheJacklwilliams]

Mr. Perinksi, once again you provide a complete well thought out designed and implemented product. Your work speaks for itself. Thank you.

[@iq0099]

Suggestions V3: 1- The holes should be 1-sided so you can insert one side and glue 1 side 2- Label on the side and top to visually see the content 3- Stackable + Self Aligning so that they dont fall or slide - and fit side-by-side 4- Carry Handle - Option - to hooks up in the same manner with a pin 5- Carry strap - Option - to Print

[@Revvek]

Very nice design! I love the tiny T square tool! Never seen one of those.

[@jorgecanales7138]

Your works always are incredible !!.

[@dadigor]

Valera, as usual, everything is super!

[@BrianBehm]

Great box solution! Making them stackable so they don't slide would be really great.

[@V.Perinski]

kzbin.info/www/bejne/hovWgGSco7V9abM

[@BrianBehm]

@@V.Perinski That's another great video! But, I was really hoping to have the boxes in this video, with the hinged lids, be able to stack on each other. Keep up the great work!

[@V.Perinski]

@@BrianBehm I didn’t plan to make these boxes stackable. Earlier, I showed a different project designed for stacking. But these are meant to be individual boxes. Yes, on one hand, it would be nice if they could interlock somehow, but it wouldn’t print cleanly. The parts are printed with the lids facing down on the build plate, and the bottom of the box is printed the same way. So, I’d have to add slots or holes, use supports, and the final product wouldn’t look as good. Alternatively, I could insert pins into the holes, but I haven’t figured out how to do that elegantly yet.

[@BrianBehm]

@@V.Perinski Great points! I completely understand.

[@Nath_McC]

I think the only improvement I can see it to add some sort of design to allow them to be stacked without sliding.

[@V.Perinski]

kzbin.info/www/bejne/hovWgGSco7V9abM

[@user-xb8sq3xk7x]

Very nice bro

[@sttm1283]

nice boxes, you should make them stackable.

[@V.Perinski]

kzbin.info/www/bejne/hovWgGSco7V9abM

[@darkfrei2]

Спасибо Валера!

[@jeanyvespochez]

Very nice boxes ! could you add some more lock to lock one box on top of another one ? and add some groove so that the top box is constrained to the bottom box ? would be an awesome addition IMHO.

[@V.Perinski]

kzbin.info/www/bejne/hovWgGSco7V9abM

[@MrJottaD]

Hi love your videos, I have a question what is the diameter of the silicone rubber sponge strip that you use 2mm or?

[@V.Perinski]

@@MrJottaD foam rubber 1,8-2mm

[@Revvek]

I have a suggestion. Maybe have an option to print a lid that lets you install a thin clear acrylic sheet?

[@V.Perinski]

It's entirely possible.

[@SpaceTimeAnomaly]

What filament material to use? Does PLA work or is it to brittle?

[@V.Perinski]

For the box PLA, ABS. Locks are best printed from ABS, it is soft and malleable for a soft latch.

[@bitsurfer0101]

@@V.Perinski Would PETG work okay for this project?

[@V.Perinski]

@@bitsurfer0101 A lot of people print it and they like it. I prefer ABS and PLA

[@antonnik9670]

вопрос, а есть какой-нибудь лайфхак как обращаться с цианокрилатным клеем? Как я не пытался выпендриваться с баночками, и носик из иголки делал, и оставлял шпильку в носике, всё равно носик застывает и потом пробить этот клей прям проблема. Клей использую космофен в фасовке с обычным длинным носиком.

[@V.Perinski]

У меня нет решения.

[@miklfaradey7306]

superBox 👍

[@bOBERmASTER]

печатал (и чертил) разные варианты под клипсу, даже если она работает по резьбе винта м3 выработка самой клипсы минимальная (пла/петг) по этой причине как мне кажется практичнее использовать все же винты м3 40мм чем шпильки. ну и работать с винтами проще чем со шпильками

[@fernandoae]

Nice job! thanks!