4 AND 6 CYLINDER ENGINE TAPPET SETTING CUMMINS KRILOSKER JCB ALL ENGINE.HOW TO SET TAPPET 6 BT ENG

[@aliarmaan508]

Bahut accha se aapne sir explain Kiya wonderful easy se your are best teacher love from Saudi Arabia

[@MohdArif-lz9bn]

बहुत अच्छी जानकारी सर आप का धन्यवाद और सर आप का मार्ग दर्शन रहा तो कामयाब भी हो जाए ये जानकारी कोई नही बताता सर धन्यवाद

[@Sharufgan]

I am kerala. Bahuth acha class 👍

[@atozform_Official]

Most Helpful Video❤❤❤❤🎉🎉🎉

[@maheswarmajhi5470]

Sir your video is helping a lot

[@Prathvi514]

bahut accha tarike se bathaya sir 👍👍👍

[@arshadjameel9236]

Excellent bhai bahut achha explain kiye aap

[@srkyousafzai2888]

Love from 🇵🇰 Pakistan ❤

[@arvindnak]

Tappet clearance is wrong, 0.25mm for inlet valve and 0.50mm for exhaust valve in 6bt engine. Remain good video. 👍👍

[@Aniketankit1234]

Bhai apna number de sakte ho kya mujhe aur bhi kucch puchna hai

[@khbarbhuiya1483]

Sar but achi lagi ho thnx

[@Ranajha1]

Nice 👍👍 love u

[@EbuTECHinfo]

nice video , clear idea of tappet setting by dividing 360/3 parts and writing 153624 firing order taking 1st cylinder piston at TDC and rockers in dancing possition

[@rajbahadur2162]

Namete. Sar bahuta axh video hai sir g

[@rakeshpaswan7958]

Achha lga jankari aapka

[@NasirKhan-nm2kp]

Im from Pakistan 🇵🇰 i see your All video 📹 very good sir 🙏

[@NasirKhan-nm2kp]

Thanks you

[@ramkumarmarko3488]

💔🍌🍌🇦🇨🇦🇨🇦🇨🇦🇨

[@ramkumarmarko3488]

@@NasirKhan-nm2kp p

[@ramkumarmarko3488]

@@NasirKhan-nm2kp p

[@ramkumarmarko3488]

🍌🇧🇧

[@bobwa399]

Is it ok to set tappet loose after a fresh engine rebuild? the idea is to let valve seat to adjust properly cause they were built new too.

[@adnanmalik1033]

Thanks for sharing your knowledge

[@aresbowen135]

you prolly dont give a shit but does any of you know of a trick to get back into an instagram account?? I somehow forgot my password. I appreciate any tricks you can give me

[@tylerdarren3985]

@Ares Bowen instablaster :)

[@aresbowen135]

@Tyler Darren I really appreciate your reply. I got to the site on google and I'm waiting for the hacking stuff atm. Seems to take quite some time so I will reply here later when my account password hopefully is recovered.

[@aresbowen135]

@Tyler Darren it did the trick and I finally got access to my account again. I'm so happy:D Thank you so much you saved my ass :D

[@tylerdarren3985]

@Ares Bowen no problem :)

[@DhananjayMurmu1993]

Good job 👍

[@drubchohan1712]

Love you sir very nice idea .

[@aminulislam-ye7vs]

Thank you guruji,, from West bengal.

[@Patha305]

Nice video sir 👍

[@rajbahadur2162]

Namaste sar g sar mai nepal hu sar bahuta axh video hai

[@bhupendersingh1950]

Good job sir khub achhy se smjhaya pr smz nhi aya

[@abungbalaitonjam8332]

master ji app ka chanell mera ko bahut pasan he

[@nikhilgarg292]

I just wanna know how we got 1,2,3,6,7,10 no. Valves order for 1st round and remaining for 2nd round?... What's the reason behind these nos.

[@amitrai-lk5fl]

All these valves are in closed condition

[@Visible-anna]

Sahi

[@shahbazansari5368]

4 5 8 9 11 12

[@MukhtarAhmad-m8k]

Good job sir g.

[@VIKASHSINGH-ue9ll]

Best hai sir ji

[@kewalsingh9934]

Very good👍👍👍 sir ji

[@mohdsan3056]

Thank you sir love you

[@zeyaulhaque6592]

Very easy

[@saydsajjadhussainshahshahg2156]

MashaAllah very nic sir

[@monirai6156]

Bahut hi aacha laga vaiya

[@JitendraSingh-ch4uf]

Sir firing order m engine sabse pehle 1/5pr fire karega 3/6fire karega2/4 pr fire karega fir engine start ho jayega

[@shivjiprbhaa7597]

🙏 very good sir

[@dibakarsharma4501]

Nice sir..

[@VIKASHSINGH-ue9ll]

Super

[@rahamankhan8715]

❤❤ thanku sir

[@bilalkhadaabrahussein1300]

Good work

[@kgmechanic7356]

KG MECHANIC 💯💯💯💯💯💯

[@SujeetKumar-z4h5w]

Veri nice video

[@AMARJITSINGH-go1cu]

Nice video

[@nesarkhan9740]

Love u bhai.

[@Efforts....]

Good knowledge

[@VIKASHSINGH-ue9ll]

Osama

[@juliussangma8274]

Ek bar mein hi kya hum intake aur exhaust kar sakhta hai ya different

[@technicalmanish9032]

Firing order se dono

[@VishalSHarma-ku5zh]

Tuanku sir 🙏

[@gyanChannel-z7i]

Nice❤

[@MuhammadNasir-lz5rb]

Good brother

[@manojpatelverygood1614]

Good 👍

[@jasssaini2886]

very good sir ji

[@mohammadhelal5245]

Thanks so much brother

[@srikantapolley1997]

Sir vedio bhohuti achha. But tapit clearance galat bataya.

[@Jaihindautotech]

bhai mere chanal pr iski puri vdo subah 7 baje aayegi dekh kr jrur batana koi kmi to nhi h

[@bluepen215]

Good h

[@purnachandramahanta1641]

Thank you Sir

[@alimotorgarage8618]

sir पुली को 120 डिग्री कैसे नापते है जबकी पुली तो गोल होती है सर पुली नापने की एक वीडियो बनाये सर अगर पुली पे कोई नीसान नही है तो कैसे पिस्टन की टॉप पोजीसन चेक करे

[@MrAmanrakhra1]

Yes same question

[@Jaihindautotech]

Mere chanal pe prectical h ap dekh skte ho

[@tienthanh2537]

Bạn via (quay) máy cho pít tông máy số 1 lên DTC rồi đánh dấu A vào buli và thân máy cho thẳng, rồi tiếp tục via máy cho pít tông máy số 5 lên DTC rồi đánh dấu B vào buli ta được cung tròn =120°, tiếp tục Via máy cho pít tông máy số 3 lên DTC ta đánh dấu C vào buli, lúc này ta được 3 cung tròn 1 cung tròn bằng 120°, 3 cung tròn bằng 360°bạn nhé.

[@jasssaini2886]

Good sir

[@AshokKumar-wj1zg]

Sir tdc ka pogisan me dono push rad free rahega tab samjege ki pdc pogisan me hai

[@manojpatelverygood1614]

❤ salute

[@HBKHAN-ir3cb]

Good Sir g

[@bluepen215]

Good

[@vendravenugopal8635]

Exlent sir ji

[@danishrajput8517]

Good sir

[@kapilgogoi6880]

Thnk you sir

[@anwarmohommad7001]

Goooooood

[@sushanjoshi6231]

Hello sir, i m big fan sir i m from nepal, i just wnn know about v6 petrol engine tappet setting plz sir

[@technicalmanish9032]

Which Engine please send all details

[@ansariramzan8395]

Thanks sar

[@rakeshvk5042]

Thank u so much

[@shyamelectronics2417]

Thanks sir

[@hafizhayat2492]

Sir 8 cylinder v type pe bhi aik video banaye please

[@mdjasimuddin762]

Thanks. Sir.

[@Laxmikantwahane]

🎉sar hame s m l for siledar tepet setibataeasar❤

[@vinayakkalbande9372]

Sir exhaust ke valve bahar bahar hi rahenge n sir heat ko bahar nikal ne ke liye aapne. Intake exhaust intake exhaust dikhaye

[@apurvasingh2702]

Kse apne cut lgaya 120 degree ; dhng se smjhao sir..kuchh smjh ni aaya

[@afsalali89]

Sir good videos. I need 4 cylinder sitting video

[@musmanbashir7098]

U can set easily for 4 cylender according to firing order.....firing order iz 1342.

[@sajjadhossen7673]

vay sab, kon engine main kitna mm tappet clearnce rake e kese pata hoga

[@santoshbhati6071]

Sir aap pistan tap setting ka vidio bnao

[@Jaihindautotech]

Mere chanal pr h ap dekh sakte ho

[@sukhenmistry800]

Sir ji, ek over head cam ka tappet setting video upload kijiye...

[@technicalmanish9032]

Ok

[@shrikantkumarjena4439]

Sir ek video Bumping clearance par banayie..

[@sambhucharan9927]

Thank you sir ji

[@dibakaradhikary8239]

OK sar.ji

[@prakashchaudhary9238]

❤❤❤

[@lipumohanta8972]

12 vt cylider ka keise tappet seting karajaiga

[@sidhikal8510]

Sir HA394 ka ful video chahiay

[@KunuJani-y2j]

T Q Sir🙏🙏🙏🙏🙏

[@golugold1668]

Hiii golu kumar

[@pawankumar6863]

Sir ji aap btate sahi ho pr aapki problem ye h ki aap sab method ki ik sath khichdi pkka dete ho Hmko ye smjh mein nhi aata h ki aap kon sa method se bta rhe ho To please ik ik method ki video alg alg bnaye Jese aapne do round mein Puri tappet settings ki baat ki h usme aap ne bola ki 360 ka ik round hota h fer aapne bola ki 750 ka ik round hota h ye baat smjh mein nhi aa rhi h or Jo insaan aapne fly wheel pr lgaye h usme aap number daal dete to jldi smjh mein aa jata tha mgr ab kuchh b smj mein nhi aa rha h

[@asokanarajun1859]

Perkins Generator model2022 G N C 6 ciylanderhow much Tapit clearance

[@YogdanBag-hh9nx]

Sir kubota hervester ka video upload kijie

[@sudiptamoharana3273]

Thank you sir👍

[@hanskumar3947]

Sir kaise pata chalega ki exhaust valve kaun sa hai or kaun sa inlet valve C 4.4 diesel generator me caterpillar

[@ashokbharti4167]

बहुत बहुत धन्यवाद सर, मुझे बताएं कि पहला राउन्ड मे कौन कौन सा वाल्व डांसिंग पोजीशन मे रहेगा और दुसरा पोजीशन मे कौन कौन सा वाल्व डांसिंग पोजीशन पर रहेगा।

[@mr.babu.srajput4743]

Sml majda truck pump timeng bs6 4salendar bataye

[@ANKURKUMAR-ln9oi]

Sir eye kitne stock ke engine hote hai

[@technicalmanish9032]

Four

[@k55gyprishnavdumpyadav40]

Thanku sr

[@abdulsayed6843]

Very good sir

[@rathoddigamber541]

Very nice sirji, i have cummins DG Model S3.8G6 can you tell me the valve clearance inlet and exh. valve is how much

[@prabhakarkmprabha4985]

Greaves tag 23 v12 engine dual fuel pump timing and gears marking details please upload sir

[@sirapathali9290]

Practical dikha dete to accha hota Sir...

[@Jaihindautotech]

Mere chanal pr prectical h aap dekh sakte h bs6 ki v h

[@arjunanasokan4908]

Caterpillar generator model c15 6cylinder how can nozzle and tapite. Valve seting.

[@igarsansen7407]

Sar ji fore cylinder ki koi video dalo type adjust Karen

[@monusaxena5444]

सर, डैम्फर पुली पर मार्किंग का मैथड समझने में कन्फ्यूजन है।

[@fareedqureshi9613]

Assalam alaikom. I want to learn , NT 855 ,G4, Cummins engine ,how to adjust cam flower gasket , & how to use cam flower tool.