Thank for this video. Sorting our some naff plumbing by the builder of our house. I’d not heard of boss fittings before but knew something link this must exist since the bath drain was going somewhere. What is helpful is knowing (seeing) that there’s nothing stopping the 40mm pipe when you push it into the adapter so caution not to push it too far in
@logicallogic99606 жыл бұрын
I don't know anything about plumbing but must say that video is very easy to follow. Nice and concise.
@nickcollins75686 жыл бұрын
You can get different boss adapters for push fit and solvent weld pipe. Outside diameter of the 40mm push fit pipe is actually 41mm . For solvent weld pipe it is actually 43mm. So the pushfit pipe will slide into that adapter more easily than the solvent weld pipe.
@UC6h-h7xIZPdaVBlAaY5hQIg4 ай бұрын
Another tip: There should be a slight slope/angle. Triple check you got the UP/TOP side in the UP/TOP position.
@briancarno88375 жыл бұрын
Very informative and easy to understand a few helpful tips too....Thank you for taking the time to make this video
@chazs0016 жыл бұрын
Well done mate nice and simple explanation
@g1briank4 жыл бұрын
Thanks, just what i was looking to confirm.
@UseitLoseit6 жыл бұрын
You lubed that hole and inserted your pipe like a true pro.... :)
@MichaelHarrisIreland5 жыл бұрын
Thanks, just want I wanted, all the best
@rezaulkarim837011 ай бұрын
Thanks mate
@狼-n7s2 жыл бұрын
Great video mate. Thanks
@paolomenna15272 жыл бұрын
Amazing video.. very clear 👌 Could you I ask how would you remove it if needed to be replaced?
@brianoneill3506 жыл бұрын
Very good video. Nicely explained
@jonathanblackett52584 жыл бұрын
Very helpful. Thank you!
@dannymassive6 жыл бұрын
Simple and easy to follow instructions. Thanks :)
@antoniogalluccio42132 жыл бұрын
Hi, would you please tell me if you are supposed to fit solvent pipe or push fit 32/40 mm pipe in that black rubber? Does it work with both?
@vlratcliffe13 жыл бұрын
Hi thank you I'm about to buy the stuff to do mine . Just one question when you push the white pipe in to the rubber is there a stop point when it gets to the end of the rubber or the adaptor. Or will it keep going all way in to the black pipe . I guess when I buy mine I find out . It so i dont push it in to far and block the pipe . Or should I measure the leanth and mark the white pipe and go in as far as the mark cheers
@robertrushbrooke10282 жыл бұрын
It can keep going if you force it through. There isn't a stop point.
@salam2383 жыл бұрын
There are some negative mentality people that they disliked the video... O man what do you want more than it?
@antoniogalluccio42134 жыл бұрын
This pipe is 43mm because it is a solvent one, I can see it by the thicness of the wall.. so the outside diameter is bigger and as such it is more difficult to fit in
@pavchandi94556 жыл бұрын
Very nice video
@Chris-uu6dg3 жыл бұрын
Thanks for video, what size hole saw do you need is it the flowplast one? Thanks
@bendennis77302 жыл бұрын
54mm 👍
@stevenmoreno70683 жыл бұрын
Keep up the good work mate 👍🏼
@pavchandi94556 жыл бұрын
Can you make one video on self level compound plz
@southcoastsealantsltd3 жыл бұрын
Very helpful thank you, take a look at my silicone sealant videos you shall be entertained
@Evoque7864 жыл бұрын
You didn’t show how far to push in ?
@martinfox19714 жыл бұрын
If you look inside the rubber there's a but that stops you going too far. It's about 2.5cm in.
@cubehire36535 жыл бұрын
OK but lose the stupid music.
@arebrec5 жыл бұрын
Have a thumbs down for the annoying unnecessary music.