5.7L HEMI VVT - No Tune Required - Performance Camshafts (MDS and Non-MDS)

Shop Our 5.7L HEMI VVT MMX: www.modernmusc...

[@ryanpitt4633]

6.1 crank power on a 5.7 platform is very nice for a slap in cam! I cannot wait to install and tune my custom grind i just purchased from you guy's!

[@bryanunion5110]

Working with Byron to get a custom cam for my 6.1. I can’t wait 💪🏾💪🏾

[@chrisgunningsr.5620]

Also do u have a video on the sound of this cam?

[@austin_94gt18]

I wish you guys made more parts for the early hemi rams with non vvt engines.

[@4g63ALLEN]

Is that dyno run using the engine pictured with the ATI dampener? That would skew the numbers correct? Because people are claiming roughly 15hp freed up from the dampener change alone. Would like to see the actual video of a stock dampened engine with just the cam

[@WilliamEngleman-pl5kc]

Excellent drivability without a tune. Slight exhaust tone change, and very slight lope. Definitely different than stock. Pulls smooth, and seems to have smoothed out that weird low/mid rpm hesitation. Seems like there is more on the top end, but hard to tell how much on the butt dyno. Curious if it will drop off like a stock cam or if you can tune it out to 6250-6500

[@Joey-ci4zu]

Is the chop noticeable? Want something like this cam since my stock is going out and down want my truck down for days on end putting new parts on. Still looking for a chop though

[@igloo_coupe]

What would a good choice be for a 10-11 psi procharged build? Looking for more mid to top end performance. Thanks

[@gregsilva1230]

I'm going to assume these cams will be happy on CARB biannual smog tests??

[@MrTexasborn81]

Would this work with the Pulsar on the fly inline tuner? Curious if that is possible

[@jeffmiller2433]

What stock cam is that from on the graph, a 2500 or 1500 truck? Is this cam essentially a 1500 spec cam mated to 2500 cam non MDS? I have a 2011 1500 5.7 that needs repair from a lifter failure.

[@robertpoggi2661]

Will it benefit from the Diablo 93 octane tune ?

[@will2583956]

Seems like a good choice. Does it have any chop to it?

[@byronwalker3606]

no, it sounds like factory

[@owningit625]

I just had the NTR/NSR Cam installed in my 14 Pursuit 3 days ago. It’s not dramatic but it does have a slight chop to it. You can hear each cylinder firing more noticeably. The stock cam sort of sounds more like a humming, less delineation of each cylinder firing. So far I’m noticing and enjoying the difference! If you want a better-than-stock replacement for your trashed stock cam/lifters, I’d recommend!

[@byronwalker3606]

Thank you for the positive feedback! Glad to hear you are enjoying! @@owningit625

[@honeybadgerjones3887]

They have a video of their Delmonico Red truck with exhaust and they go to the tail pipe to hear how it idles.

[@hasansalah6609]

Best cam for 5.7 hemi ?

[@chrisgunningsr.5620]

Do you have a ph#? I got some Questions

[@roberthammond4642]

I want to delete my mds on my 2011 dodge ram 1500 4x4 5.7 do you have a kit with this new camshaft

[@1470boyz]

Go onto their site , they do have one

[@baderkm27_]

Will the mds system work after installing the cam or it will be disabled

[@slowboat7647]

Did you even listen to the video, make sure you choose the right one for your application they have one for either or

[@chrisd2486]

With the mds delete do you have to do a tune

[@DavidFettucine]

No custom tuning needed but you would need to disable it with a flash/handheld tuner like a diablo tuner to delete/disable the MDS system in the computer.

[@chrisgunningsr.5620]

Where can ya buy it & how much??? Non mds

[@DavidFettucine]

The non MDS cam is about $620 before tax on their website

[@cooptrail]

Anybody tried it yet