[ 5 STEPS ] OLED Display NOT Working | Fixed Error | Errors Solved | 128*64 i2c 0.96" | Arduino.

If your OLED display is not showing anything: Check that the OLED display is properly wired to the Arduino. Double-check the OLED display I2C address: with the OLED connected to the Arduino, upload this code and check the I2C address in the Serial Monitor.
This channel to share exciting videos of Arduino projects,Electronics and electrical easy diy projects to share with you I hope this projects will be helpful for you to create something new .
Do not Forget to like comment and subscribe my channel.
SUBSCRIBE LINK:-
/ @slideas1
Arduino Sample Code :-
1. www.mediafire....
2. www.mediafire....
i2c lcd display Library :-
www.mediafire....
Full Package :-
www.mediafire....|+Fixed+Error
My Other videos :-
1. Home Automation using arduino ir remote control sensor
• Home Automation using ...
2. How to make bike & car security system using arduino gsm module
• How to make bike & car...
3. LED chaser arduino mega with 32 effects | 53 leds
• LED chaser arduino meg...
4. Top arduino projects 2021 for covid 19 | coronavirus protector | Sterilize Stationery
• Top arduino projects 2...
5. NEMA 23 | NEMA 17 | NEMA 34 with TB6600 stepper motor driver and Arduino
• NEMA 23 | NEMA 17 | NE...
6. Arduino Target Following & Recoding Robot.
• Arduino Target Followi...
7. How to use W1219 Temperature controller/DUAL Display
• How to use W1219 Tempe...
8. How to make an LED VU-meter using Arduino.
• How to make an LED VU-...
9. LED chaser with 32 effects |led patterns with Arduino | Code in Discription
• LED chaser with 32 eff...
10. How To Make Automatic Touch Less Non Contact Water Tap At Home/office
• How To Make Automatic ...
11. How to make best car reverse parking alert system using arduino / DIY / arduino projects
• How to make best car r...
#OLED_Display #OLED_Fixed Error #OLED_not_working

[@SoCalRobots]

Thanks for reminding me about the adress selection! 0x3C for 128x32 for my tiny screen

[@ferdosibegum5398]

My oled screen have not any reaction . Please help me

[@jumbo999614]

I bought this and haven't used it yet and I already broke a bit of the screen at the lower left. Is it broken?

[@quangmi3402]

I SIMULATED SSD1306 128X64 I2C ON ARDUINO UNO BUT WHEN I START CHECK THE SCREEN IS ONLY BLACK. PLEASE HELP ME. THANK YOU

[@wanhar7374]

Super, thx gan sangat membantu

[@RiddheshVeling03]

I have SSD1306 1.3 inch OLED. When the OLED is powered, more than half of the screen is covered in random pixels. Please help to solve my problem

[@supriyadutta7713]

Same for me

[@supriyadutta7713]

Have you found the fix!

[@AntekCookie]

same, but like 9/10 screen is covered in random pixels

[@Manticore1960]

Most, if not all 1.3" displays use the SH1106 driver, not SSD1306. You will need the SH1106 library to run it.

[@AntekCookie]

yeah i also found that you can just test every library and see which one works

[@arvinds.285]

It says no i2c devices found. Need help

[@sangeetguha51]

same problem

[@xyrx4319]

Me too

[@sneakyhiders6575]

Same

[@Nythron_IV]

same here

[@GWorxOz]

Another useless music video! 😡 🤬