50hp mercury carburetor clean

Bottom carb float was sticking

[@mr.cryptobull1520]

Just bought a boat with this motor. Now I feel confident to do the carbs.. THANKS

[@danielmeecham464]

Well done sir! Thanks for sharing. I've got an identical motor that's idling just a little rough. Mine motor is a 1992. I just did a complete electrical parts overhaul. I was apprehensive about digging into the fuel system, but thanks to your video, now I'll remove and clean the carburetors.

[@officialWWM]

How did it work out for you?

[@danielmeecham464]

It worked out great! I simply focused on the basics: fuel, air, spark. I just cleaned all the parts, an replaced ones in doubt.@@officialWWM

[@CTRadventures]

Thanks for this video! We just bought an 88 ranger 393v that came w a 6 cylinder 87 Johnson 150. The oil injectors removed to run 2 stroke. This is my first bass boat and power engine, so I'm trying to learn as much as possible. Again I'm completely new to motors, sometimes she seems she's a little rough on idle so I thought, hmm maybe the carbs need cleaned

[@officialWWM]

Thanks mate. Very detailed and extremely helpful! Cheers from Tasmania.

[@colvinau1403]

Mans did this shit one handed

[@zeeduk]

Will want to clean each intake hole behind the carb before putting the carbs back on as well but great jobs showing how easy it can be.

[@outboardsandtoys8413]

I agree I have seen screws and other stuff in the reeds

[@simonandersson8197]

what does the holes in the back of the carbs? i have a mercury 50hp 2 stroke, and it is more fuel flow on one carb? and bogging when i accelerate. from sweden not very good english

[@simonandersson8197]

done carb clean 13 times now and changed membran

[@jamescraig8601]

Change your filters

[@Deon-ot2vi]

Thanks for the great video. Helped me out.

[@savagenomore]

that float is adjustable, just bend the little metal tab the needle hangs on

[@outboardsandtoys8413]

You are correct I did not notice it when I done it

[@7tosand]

I didn’t see any gaskets when you took the carb apart, or on the intake manifold. We’re there any gaskets?

[@emmettjones1961]

Excellent Great video

[@FullThrottleGarage69]

very good video

[@quranwithurdutranslation7199]

Great work... Just subscribed your channel.... From : 71 Satisfaction Inn

[@ngbay160]

Took my boat out today. Idles fine and starts right up, BUT once i open it up all the way it will run but it acts like it fights for gas? Dirty carb? Fuel is fresh and the gas tank is new

[@outboardsandtoys8413]

I would say so starving for fuel sounds like the high speed jets

[@outboardsandtoys8413]

Easiest way I know how to tell is choke it when trying to get on plane if it increases rpm for a few seconds most likely it's the jets

[@jordansyrus8900]

Hey bud do you know if you can buy cowling covers for a 1994 50 hp mercury I’m thinking about buying one but wanted to know if you could buy this part still

[@travelguy1564]

Did you take off the oil pump system and just convert it to pre mix? If so, how did you do it?

[@giloquendo]

Great video question does that high speed jet has a hole or is it sealed

[@officialWWM]

It has a hole. That’s how the fuel goes in!

[@bumpskier88]

hey , is it not necessary to use a gasket when remounting the carbs?

[@outboardsandtoys8413]

Yes there is a gasket behind the carbs on the intake alot of times it is stuck to the carb or on the intake may not be able to see it on the video

[@jamescraig8601]

Mine only has two carbs.

[@kingpondah990]

What did you use to clean the carbs?

[@outboardsandtoys8413]

I used a ultrasonic cleaner I got from harbor freight and the used air to blow through the journals

[@Eric-fq5wx]

Is there an idle jet?

[@outboardsandtoys8413]

Yes I did not go into that on this video cause u have to set the screws on each carb they can be very tricky to adjust if u dont get it right it will Ethier be lean or to rich the best way to set low speed is with gauges

[@1988aweb]

Are there no gaskets between motor and carbs?

[@mylotmarshall8885]

What year is that motor?

[@colvinau1403]

90s probs

[@tnybo13]

Half a job, basically if you're not cleaning the whole system a waist of time.

[@outboardsandtoys8413]

really where is your video and whats half the job also this motor has been doing perfect on this half a job waste of time