(6/12) FrSky TARANIS Radio - Adding and using custom sound

In this video we continue on from the other videos in the series (uploading firmware, creating a basic model, adding extra channels manually and using OpenTX companion/curves) and this time we will download, add to the radio and use custom sounds.
In this video we will cover -
- Introduction (0:02)
- Demo of sound on the radio (1:28)
- Options to create and add custom sounds (2:18)
- Overview of the Amber sound pack (5:08)
- Adding the sounds to your radio (7:48)
- Setting up the radio to play the new sounds (10:32)
- Setting up OpenTX Companion to use the new sounds too (13:43)
- Summary (16:48)
Thanks for watching, please LIKE and SUBSCRIBE!
Happy flying!

[@dragonfly1949]

Excellent video. I had been trying to add sounds for hours your video explained it to me in minutes. Very clear, concise, accurate instructions. Thank you for your time and effort.

[@JCQuadcopters]

100% agreed

[@ZITON1]

LIFE SAVER. Thanks to you I'm learning how to use my taranis. I would have given up without your videos.

[@lashley370z]

As always, very well done. Thank you. One thing I'd add is that after making the Special Functions changes, I believe you need to write those changes to the radio. Thank you for all of your help. I successfully build a quad from parts and it flew! Much thanks.

[@williamb3323]

You're great! recorded 3 years ago and still helpful to us today. Thank you sir!

[@maixechrys6264]

Hello, It abolutely works! I just wanted to thank you and encourage you to continue your efforts for providing tutorials and usefull tips to the community. I was able to properly setup my DJI F450 quadcopter with APM 2.6 using X8R receiver and Taranis Plus radio though your videos! Congrats!

[@Painless360]

Maixe Chrys Thanks for the feedback! Adding more all the time. Happy flying!

[@gordinir7]

Vote Painless 360 for President. Thank you a lot for sharing all this stuff with us.

[@derrnav1530]

Lee: I enjoy all your videos a "Bits and bobs". I could not get the 6 flight modes to work until I read your article @ OpenTX University. Yeah Whoo it works! I also added the wav files to play with the flight modes. I would recommend maybe making a video, in your spare time , showing the whole process for multrotors and Taranis. Thank you.

[@Painless360]

+Derr Nav We cover that early on in the series. Use the playlists to find videos by subject. Best of luck!

[@derrnav1530]

+Painless360 Lee: Custom Switches is now Logic Switches in the software . And I don't have the Taranis Plus radio. So it was a learning curve to see how to do it with present day software. Also adding sound by way of Logic Switches. Thank you so much for the videos and information. Next up is to get rid of the jiggling in the OSD information on the FPV screen!

[@cr6925]

Great vid! That setting the Taranis path to see the SD card sound files folder really tripped me up. Having watched your vid, problem solved :-)

[@Painless360]

Perfect - that's why we make 'em! Happy flying!

[@steves8113]

Thank you very much for your video series very helpful. I'm more than happy with Taranis transmitter.

[@harryholt6484]

Cheers for the great videos. If it helps any one else -I tried to copy new sounds over the existing sounds but it would only play the original sounds. Having already copied and saved the original sounds on my PC I then deleted the originals sounds folder off the SD card. Replaced with the new sounds complete folder and it worked great ! Happy flying now with an even sexier voice.

[@dsturner244]

its been said lots of times but thank you... your videos are GREAT .

[@crispy2473]

Great video and very informative. Very helpful and easy to understand. Many thanks!!👍🏻

[@dinozoff7161]

Hey man i feel like i'm watching an online lecture ! Great Job ! thank you

[@Painless360]

+Dion Gjermeni Thank you! Happy flying!

[@jps99]

Thanks for all these great videos!

[@MrGrahamanator]

Oi Mate! Your videos are the damn best of RC! Thanks so much! Cheers!

[@Stirlingv8]

Brilliant video - thanks. For what it's worth, the sound files all have to be at 32KHz - took me a while to work that one out creating individual sounds myself.

[@Rando104854]

awesome!!! thank you so much. very well done and helped me so much. ⭐⭐⭐⭐⭐

[@Painless360]

Glad it helped! :D

[@lukegranger3458]

For those that cant find a download link for the amber sounds. its available here: open-txu.org/v2-2-resources-2/

[@SubToTripleThreatRC]

Brilliant, thank you very much for sharing, thumbs up!

[@silbernersurfer8264]

Great, thanks a lot! It has worked at first try!

[@shawncruise2030]

Great video. I had problems connecting my Taranis to USB and copying in the files. The X9DP would freeze up when attempting to copy or delete the files and I had to pull the battery out several times. Removed the microSD and used an adapter to put in my computer and loaded the new files that way. Also need to be careful with the currently available Amber Pack. The only version available is for the OpenTX firmware 2.1. The sound pack will work for the OpenTX firmware 2.0 but many of the numbered file names have changed in the SYSTEM folder. Need to review the text file in the Amber Pack listing what has changed between 2.0 and 2.1. Make the changes for 2.0 if running firmware 2.0. In my case I was using a switch to read the voltage to me and the decimal places were read incorrectly because the file names need to be updated.

[@Painless360]

There are Amber packs for OpenTX 2.0 and OpenTX 2.1 that supported the changed indexing and added the extra support. Happy flying!

[@seantheberge5456]

Thanks for the help!

[@MXTRAMPOMX]

Thank you very much I was trying to download from the link in the video and it's dead thank you very much love your videos !!!!

[@wrichards123]

cant get the sound files to show as a choice in the trasmiter... only default SYSTEm list...

[@ourblue]

well explained but having trouble replacing the welcome sound. Have recorded other sounds for names of planes etc. I imported spitfire engine and edited it changing as required. Placed on sd card in system sounds and renamed as hello. Still not recognised. Hope you can help.

[@Painless360]

I do recall the name of the welcome sound changed so check the notes for the version you are using. If you’re using the Amber sounds pack then that comes with a file that shows you what they all are.. best of luck!

[@madmatz2112]

Thank you so much! :)

[@MichaelEber]

I have OpenTX 2.1.3 installed on my Taranis. I followed these instructions...using the Amber 2.1 sound file pack. But after doing so I do not have any sounds at all. Not even the intro verbiage!

[@Painless360]

Best of luck with it!

[@anythingrc995]

Hi before you transfer all the new files do you have to delete all the sound files on the Taranis after you have backed them up? Great job on the videos they are very helpful.

[@Painless360]

Anything RC, Chris Clarke I would copy the originals so they are safe and then copy the new files over the top of the existing ones. Happy flying!

[@breezyjr]

Awesome videos so far... Sub'd and liked...

[@Painless360]

Welcome to the channel!

[@breezyjr]

I don't have my radio yet, but going through all the videos, and am through 5 or 6 so far... Just have to say, this appears to be the greatest radio ever.. I can use all my DSM helis I already have (Of course with the added module), I think I can even use the couple futaba quads I have, but even if I can't, I only have 2, so swapping them will be easy enough... If the gimbals on this radio are "ANYTHING" like my JR 12x, I will be in heaven!!! I love the weight and feel of my 12x, and this "looks" so much similar... Thank you for all the videos, it has been so very helpful, as I was very worried about programming it correctly... Using it with the TBS Crossfire... And, am excited! hehe (Like a little girl getting a pony for Xmas..LOL) Can't wait to check out your other videos, especially the CC3D. Picked up a used quad with one, and I am not familiar with it at all... You ROCK!

[@harleywolf5028]

Hi..being a new Taranis Radio user, your videos have helped a lot I have gone through splash screen model icons, sounds, etc. but what is puzzling me is when you picked you "test bench" model Amber says "Throttle Active". How did you program that? Thanks, Stu

[@Painless360]

+Wolf-Frag FPV I've set a throttle cut and when the throttle cut is active I setup the radio to play the 'Throttle disabled' sound and play 'Throttle Active' when in the other position. Hope this helps.

[@Ricardo_Rooster_Gsg9]

I´ve got a radiomaster Tx16, and i think that it works like the taranis since they use the opentx. Is it possible to add a sound when i turn the radio off? Thanks

[@dinozoff7161]

Open Tx Professor!

[@pierstaylor7780]

I’m trying to get the word “stabilised” I have the way file on pc but it will down load to add card and can be seen on my jumper t18 but will not play. Any help would be most welcome

[@Painless360]

All of the steps I use to get it working are in the video. Best of luck

[@alaingosselin8764]

THANK YOU ;)

[@Skeptic2006]

I followed these steps but my Tanaris started making strange noises and could not find any sounds at all! Even when I replace the Amber sounds with the originals I still can't find them neither from the radio or open tx. Anyone know what might be the problem? Files are in right folders and sd path is the usb drive(e:) Why would it not find the originals?

[@tomraniere2703]

Just for every ones information - when you name the Audio files - they must be 8 characters or less .. otherwise they will not be recognized.

[@KGFlyer55]

Another great video, thanks, just wondering how do you change the welcome track when you power on your Taranis? Thanks again

[@Painless360]

KGFlyer55 You are not using the playlists are you ;) kzbin.info/www/bejne/p3WXh3xjbcd5eck If you did then you'd have found this video - kzbin.info/www/bejne/aJ69Zn2Xactro80 Hope it helps. Happy flying!

[@crossfpv781]

Hello friend need some help my Taranis X9D not called more shock absorber have the upgrand Interrupted . You know how to solve this ?

[@Painless360]

Not sure what you're asking. Do you mean that it's been dropped?

[@mydealzTV]

hey, thank you for all the great videos. helped me a lot. Now I have got a question. I added some voices in the "special function" menu. that works fine, but now when I turn on my taranis, the girl reads all the sounds (also the funny ones). Do you know how to chance this?

[@Painless360]

When you select the model the radio will read out all the switch positions you have set (throttle off, stabilise mode) etc. This is normal. I've never tried to disable this as its what you normally want..

[@vmbamores]

would you help me with a couple of ítems?(1) Anabela: I made all of the process and the link with the root source opens the voice in Quick Time format (not allowing me to save or change to WAV or MP·). is there one other way for me to make it or is there any other simlar page that I can use?(2) Tracks and values are played in the radio, no "sound" from "Play a sound" is Heard. ANy idea how to fix or solve?Kind regards

[@Painless360]

+vmbamores Happy to help but please watch kzbin.info/www/bejne/pZ2sooefiK97f7s and come back to me with more detail of what you've tried..

[@mattsnuts]

Thanks for this video series. For Mac users (or anyone who is having trouble getting the USB disk mode to work - I tried on 3 different computers with no luck). You can eject the SD card from the Taranis - it's located where the battery is, and then read and write to it using a micro SD card reader. Another tip for Mac users - you can use the say command (at the terminal) to record your own messages: say --data-format=LEI16@32000 --channels=1 -o airmode.wav "Air mode" Just be aware that the filename must be less than 8 characters long for the Taranis to see it. Now, a question. Is there any way to stop it reciting all my switch settings when I switch it on?

[@richardlong3615]

Somebody has probably told you how to by now but if not then after selecting the message to say move to the right end of the line for the number of times so and select and scroll down until you get an ! in front of the number - job done

[@christopherpauley8174]

hello i'm on the latest firmware and have a strange issue - i made .wav files to use, i moved them over to the radio, i can see them if i hold down menu and page to 2 to look at the sd card, but when i go into special functions the files don't show up?

[@Painless360]

Be sure they don't have too many letters in the names.. Best of luck!

[@kenmcnaughton9491]

Hi Painless brilliant videos in your series, I followed this one to the letter , but the Amber sounds are not showing up on my taranis or on the companion. I just have the originals. I put the sg card in a card reader and they are all present and correct. What am I missing

[@Painless360]

Usually because they have been copied to the wrong place on the SD card. Best of luck!

[@christinelampitt1923]

Extremely informative videos and thank you for taking the time to inform us in a way that is understandable. However, I have reached video 6 (adding custom sound) and I have hit a problem. I backed-up the original sounds on my computer and downloaded the Amber sound pack. All OK so far. I then tried to transfer the Amber pack across to the transmitter and it didn't download. So, I removed the SD card and did a download via the computer. It all seemed to download correctly and showed the content successfully on the SD card. Unfortunately, on inserting the SD card into the transmitter I now have no sound at all (original or otherwise). What am I doing wrong? Please can you help. Perhaps, at the age of 69 I should not have started a new technology venture but it seemed a lot more challenging and exciting than knitting!!

[@Painless360]

If check the individual files are in the right place in the SD card (we used OpenTX 2.0.17) in the video so check if you're using 2.1.x)..

[@christinelampitt1923]

+Painless360 FEEDBACK: Thanks for the info and for your time. Before I started to change the Firmware I decided to check the SD card files. Perhaps it is that I don't understand computer functionality. On the SD card I had created a file 'Amber Sound Pack' in order to differentiate between it and the original sounds. Having previously made a back-up of the Original sound pack installed and the Amber pack I decided to delete all sound files from the SD card and then reload the Amber sound pack WITHOUT any sub headings or folders. GUESS WHAT - IT WORKED! So it would seem that my addition of folders on the SD card somehow interfered with the ability of the transmitter to access the sound info. Sorry for being so long-winded but I wanted to save your time and effort by providing feed-back and a solution for other users. All the best

[@Painless360]

Yep, that would do it. The radio expects the files in very specific places - just follow the videos and you should be ok ;)

[@ampmunkey]

Is there a way to prevent it from playing the track on start-up? For example, my Simulator model says: "Simulator" once for start "Timer On" for lap timer "Arm/Disarm Motors" to signal between flying or menu mode (for Liftoff) "High/Middle/Low Rates" whatever position it's on I'd really like it to only announce Timer/Arm/Rates when a change occurs, and NOT on start-up.

[@ampmunkey]

Figured it out. Had to adjust the repeat option to "!-" no longer an issue. Thanks anyways, haha!

[@Painless360]

:D

[@MrTMoore55]

Well I ordered the plus a couple days ago, I'll figure it out. Question? Will the open tx work on Windows 7 I bought on just because a lot of software is not compatible with my Mac. Thanks for your tutorials I think with them I can get the transmitter programmed.

[@Painless360]

Yep, great with Win7..

[@RC-Heli835]

I did this once with the Amber Sounds Pack but seem to have forgotten the process. Also I thought I had Companion setup to where it would play Amber sounds from the PC is that possible?

[@Painless360]

Yes you can, copy the SD card to somewhere on the PC and setup the links to it in Companion..

[@dsingfsw]

Is there any way to add sound on a 6 position setup that is linked to two switches?

[@Painless360]

Yes, check the logical switches.. best of luck

[@Pastorkarlman]

Lee, I am able to access Amber pack sounds through the OPEN TX Companion, but if I try to add a new sound that wasn't already in the pack like "mycoolbeepsound.wav" it will play the sound from the special functions screen, but once I assign it to the switch, it won't play the sound when the switch is used. Is there something in OPENTX that only recognizes known sounds? I even renamed the sound to one that was in the Amber pack and it still won't play. Very strange.

[@Painless360]

There is a limit to the name of the file. Rename the sound with less than 6 letters and try again...

[@heliav8r]

Is there a way to assign specific sound to the left and right paddle sliders and the 2 pots (S1 and S2)? In the special functions list they will not register like the switches do.

[@Painless360]

+heliav8r How about creating a logical switch for values from those controls and then using that to play the sound?

[@heliav8r]

+Painless360 Thank You! That works great! I love the Taranis and thanks to your videos I am getting the programming done right! Keep em coming!

[@brettnaysmith3949]

I have made a wav file and transferred into en file on Taranis .it plays from the en file while in computer, unplug and then open sound file on Taranis , select same file and it won't play.it has the .wav like all the original files.

[@Painless360]

Brett Naysmith Then the format of the wave file is wrong - see the video for how to make sure it's mono and the right settings Best of luck.

[@brettnaysmith3949]

In the end it was the project rate.I changed it to 3200 in the beginning instead of just before exporting, thanks for you time.

[@ridgehawk1]

hey lee.. I have the amber sounds for 2.1.8 on my radio, I wondering why I have access to all the sounds but not to the number files in the sys directory? is there a way to get the number sounds.. maybe pick one I want and rename and copy it to the sounds directory? i'd have a switch for expo... now I have it saying "expo mode2" i'd like it to say "expo 20"... is there a way"thanks, bob

[@Painless360]

Not sure, I've not played with that bit much.. I'll have a look next time I'm in the den..

[@brecklietz1587]

Hello Lee, I have been educating myself thru your videos for the last few months. The wife just bought me a new Taranis Plus for Xmas. I am trying to install the Amber voice pack with little success. It seems that the domain has been discontinued. Can you suggest a new location for the voice files. Thanks in advance.....Breck

[@Painless360]

I googled 'amber voice pack taranis download' and found this - www.open-tx.org/downloads Best of luck!

[@luisbaltazar1]

is there a way to configure a special function to be valid for any model? for example, i like to assign a switch to backlight, can i make it work without individually setting it up for each model?

[@Painless360]

Not that I know of. If you find out I'd love to know..

[@EdQuigman]

Hello - A few months back I upgraded my Taranis (non plus) from its original firmware to 2.1.8 and added the amber sound pack. Now the minute timer no longer says "minutes" it just reads out the number. Any idea how to get the minutes word to speak? Thanks!

[@Painless360]

+EdQuigman you need to update the amber pack to the one for OpenTX 2.1 too. Best of luck!

[@EdQuigman]

That got it! I cant thank you enough.Thanks for all the great videos. During the Third Reconciliation of the Last of the Meketrex Supplicants you shall sit among the chosen.

[@joestubbs3138]

The Amber sound pack you downloaded from RCG's ''theKM_opentxTaranis_soundPackFull_amber_20140709.z ip'' - clicking on it comes up with ''Cannot Get'' any reason that you know off!!?? But did manage to download the amber sounds as found in OpenTx University as [Amber Sound pack for v2.2: hmvc.eu/Amber22.rar] but this does not have the two JPG,XLSX files listed under your SOUNDS file ( 5:08), which would be interesting to have. Will not change the sound settings just yet until I've reveiwed how to save the 'as is' sounds and am more famillier with the Taranis - USB drive (G:) and Taranis drive (H:) and their files Did manage to change the Firmware from V2.1.6 to V2.2.0 - thanks to your video, thanks...joe

[@AndyRCchannel]

so in open tx companion you have to know exactly what switch it is and select it or can you still move the switch on the TX and it will auto select it?

[@Painless360]

AndyRC You can still select the switch by moving the one you want when you have it selected in the menu. This is covered in the series.

[@AndyRCchannel]

thank you

[@kenmcnaughton5882]

Hi Lee, I am still trying to get my sound to work so that I can use these sound files. could you please tell me which of the pcb's holds the amplifyer system.

[@Painless360]

Sorry, no idea.. not up on all the insides..

[@happyvalley808]

Really appreciate your channel and help.I have some how fudged the process you describe in this video. i saved the original sounds as suggested. after install of amber sound pack no change was observed. i then tried to delete what was on the sounds setting and reinstall the original sounds with no luck. Now when i turn on the taranis there is no sound, when i try to add a sound to a switch the taranis says no sounds on sd card. Can you make a video on how to fix this problem ? Thanks a bunch!!!

[@Painless360]

+happyvalley808 This usually means that you are not copying the sounds into the right place on the SD card - best of luck!

[@BIGEMANN1]

Can a sound file be added to the right and left sliders , and If so how is it done ?

[@Painless360]

+BIGEMANN1 ypu can use logical switches to trigger a sound using the values from the sliders, best of luck!

[@elieeid8865]

thank you for your explanations. but the file on rcgroups does not exist anymore . do you have any idea where i can download it.

[@Painless360]

If you Google 'Amber pack OpenTX download' you'll find it on the OpenTX University pages..

[@elieeid8865]

thank you i got it from OpenTX University. and this is the link: open-txu.org/home/v2-1-resources/

[@28andras]

greetings, i've tried every single step you did yet i cannot find the config files you replaced; the link you provided is broken.

[@Painless360]

I've just used all of them from the description and they are working - which one are you talking about?

[@28andras]

i copy and paste my sound from Accapela in card sd in transmiter and in screen can see but no play.Is mp3...i change same type with sd card (just voice) and again no hear...you can help me?

[@Painless360]

+dimitris anestis everything I did is in the video. Best of luck

[@28andras]

i ask you for the archives from Tranis i see in your video but my transimter no have that archives...and you answer me (good luck)....ok no help me thank you......happy new year..

[@havoctheprotogen3732]

dude, something happened. when I turned my taranis on there were no sounds. when I reconnected it it said the sd card file had to be formatted, which would erase everything. what do I do?

[@Painless360]

Sounds like the SD card isn’t happy. I’d pop it out and see if you can read it on a PC. You’re right reformatting would delete everything on it. If you can read the card on the PC then I’d copy all of it for safety and maybe try another SD card.. Best of luck!

[@havoctheprotogen3732]

I got it fixed. I had to take the sd card out of the taranis and put it directly into my computer. I apparently did something really wrong to it because after I formatted it I had to scan it and repair whatever I had done to mess it up. I managed to find the files I needed on a forum, which conveniently had the sounds I was wanting already on it. All I had to do then was download the files from the forum and transfer them to the sd card. Now it's working perfectly! Thanks for the help and hopefully if anyone else has the same problem I had they'll know how to fix it.

[@rradcm02]

Hey painless..I just added the Amber pack to my TX. It works fine, except when I boot up my taranis, I'm no longer greeted by "welcome to taranis. In fact I get nothing at all..all other voice prompts works great..any thoughts would be welcomed. Thanks!

[@Painless360]

+Ray Richards when the radio starts it plays the sound Ike called 'tada'. Make sure you have one! ;)

[@pheonix2160]

Might want to update your video on this, the link to the zip file doesn't work anymore on the RCgroup site

[@Painless360]

Thanks, Happy flying!

[@ItsLRivera]

how do i change the sound when i turn my radio on. I have a sound from the amber pack i wanna use but cant figure it out.

[@Painless360]

Look for a sound file called 'TaDa' on the SD card. That's the one that it plays on start-up. You can change it by renaming the sound you want played to that same name. Happy flying!

[@jethroraj5553]

Is there a way to get back the original sounds if you don't have a backup?

[@Painless360]

+Jethro Raj only if you can find a friendly Taranis owner who's saved a copy..

[@jethroraj5553]

would it not be possible for someone to upload them somewhere for others, like me,who forgot to save them?

[@ridgehawk1]

is there a way to increase the volume at which a audio file was recorded... Ambers voice doesn't seem as loud as the taranis voice files?

[@Painless360]

+Bob W not easily but you can increase the volume on the radio. Best of luck!

[@ridgehawk1]

thank you... your videos are GREAT!

[@Painless360]

Thank you. Happy flying!

[@Theproof1984]

excellent series of interesting videos. I've recently bought a X9D+ and I have trouble with accessing the SD-card, and reading the firmware in OpenTX companion. Hope someon *wink wink* can help

[@Painless360]

+René Pedersen I cover a lot in the series so maybe I cover it later. Tricky to be specific without details of the issue and what you’ve tried already. Best of luck!

[@Theproof1984]

Painless360 first I tried to flash the firmware from openTX companion, seemed at first glance to be working, but got a messagebox swing it couldn't verify the firmware. Then I saw in a comment to your video of updating to opentx 2.2 that in order to update the bootloader to accept the opentx 2.2 you have to manually put the file on to the SD card, and so I went down that rabbit hole, and got in to a heavy of driver error, even though I got the manually installed drivers from open-tx.org, then I can't see either of the SD card or the eeprom

[@Painless360]

Not sure what 'heavy of driver error' is but I'd be tempted to delete the driver on the PC and start again. Remember to put the Radio in to USB mode by moving the horizontal trims to the center as you power on.. Best of luck!

[@Theproof1984]

Painless360 heavy should have been heap. I've tried deleting the driver, tried updating the driver, but no matter what it's the same problem, and every time in USB/eeprom/bootloader mode

[@CarloOSU]

Could someone be kind enough to paste a link to a working copy of the Amber Sound Pack? I am having a difficult time locating a working link.

[@Painless360]

voices-21.open-tx.org/opentx-taranisplus/en/thirdparty/

[@CarloOSU]

Great! Much appreciated! Thanks for the link and the videos! Keep up the wonderful value added work.

[@CarloOSU]

Actually, it doesn't look like the zip has all the additional .WAV files. Do you think I'm possibly doing something incorrectly? All I see are system files.

[@Painless360]

No idea, I can't see what you're doing..

[@someonesomewhere3027]

Hi, Where can I download the full package , what you just show on this video. Thanks Tom

[@twiztedmind864]

I tried to do this and when I connect my taranis to the computer in bootloader mode it won't open any of the folders, then when I disconnect the usb it won't turn off unless I disconnect the battery. It just keeps the usb connected screen on.

[@Painless360]

I've nto seen that here, can you let me know what it is when you sort it out? I'd suggest trying another USB cable..

[@twiztedmind864]

Painless360 it appears to be my laptop. The usb drives showed up as having an issue and it seems to be working fine now after windows ran a "fix" on it. Probably something to do with the two times my daughter spilled things in my laptop.

[@Painless360]

+Twiztedmind864 possibly! ;) Happy flying!

[@Rickgoldcoast]

Hi +Painless360 I have watched your latest videos on telemetry and came back to revisit this video to try to get the answer for my issue. I'm using a FLVSS to get telemetry to my X4R and into my radio. I managed to get it working but I can only get a reading of the digits before the point (for instance 15.46V it only reads 15V, or 3.88V it only reads 3V). The radio won't read the decimals. When say read, I mean "speak" because I can see on the screen the voltage in a 4 or 3 digit format, but there is no use when you flying fpv.Can you help? Thanks again, again and again.

[@Painless360]

+Rickgoldcoast Not sure, What version of OpenTX are you running?

[@Rickgoldcoast]

Painless360 2.1.6

[@Painless360]

I'm not there yet - I'll test it when we upgrade ours..

[@Rickgoldcoast]

Painless360 I've got it. You need a different sound pack for 2.1 firmware

[@Painless360]

Ah ha! Good to know! I'll cover that when we do the 2.1 upgrade videos.. Thanks for letting me know..

[@ItsLRivera]

is there a way to set my switches so when I turn on my radio it doesn't tell me what position its in for example when I power my radio on it tells me Horizon mode engines disarm

[@Painless360]

You could setup the volume to be controlled by a slider and have that down when powering on maybe.. This is a suggestion for a future enhancement for OpenTX - github.com/opentx/opentx/issues/1445

[@ItsLRivera]

Thanks I'll try that out. I just don't want to forget to turn the volume back up once the radio is on.

[@matjaz3882]

I can't get amber pack. It just don't want to download.

[@Painless360]

Nope, free support here only.. You can download the Amber pack by looking on places like the OpenTX University...

[@matjaz3882]

Painless360 okay

[@MrJoshua49651]

Can i have a link to get this sounds please!!!

[@MrJoshua49651]

+Joshua Gere loool Dont worry i got it and thanks for the video!!! really helpful

[@MXTRAMPOMX]

its not letting me download the amber pack when i save target as it saves it as a .htm file and even if i click the link it takes me to an add any ideas plase???

[@Painless360]

Not sure where you're looking - voices-21.open-tx.org/opentx-taranisplus/en/thirdparty/

[@MXTRAMPOMX]

+Painless360 thanks I was trying to download from the link in the video but it's dead thank you very much !!!!

[@B3autyflow]

Hey! Love the video's!! But I've gotten stuck, when I plug in my Taranis, my computer ask me to format the disk file... should I do this? Thanks!!

[@Painless360]

+Jaden Tout nope, try plugging the sd card in to the computer directly.. Best of luck

[@B3autyflow]

Painless360 I gave that a shot and everything is perfect now! Much appreciate the quick answer! Amazing videos man

[@danwedrat2783]

Hi, just wondering if this still works with 2.2.1?

[@Painless360]

Yep

[@alexcheok]

Where can you get Amber's "Return to Launch"? I've downloaded the Amber pack and couldn't find it. Not even elsewhere on the web.

[@Painless360]

Alex Cheok It's there - look for the file called 'rtl' ;)

[@alexcheok]

Painless360 Oh wow it wasn't listed in the jpg or excel. I must be blind then. Thanks a lot

[@Painless360]

No worries ;)

[@johnsauren4730]

A sin, the Amber soundpack isn't availeble anymore

[@Painless360]

It is! Not sure where you're looking but if you wanted a URL you only needed to ask - open-txu.org/home/v2-1-resources/

[@johnsauren4730]

I was looking in RC Groups.com, that link is broken, and tried to search in Google. Thank you for the link, i got the file now!

[@MikeMcCarty6453]

What about changing the welcome to Taranis sound?

[@Painless360]

+Mike McCarty check out the sound file on the SD card called 'tada';)

[@MikeMcCarty6453]

I see it on the SD card but i don't know how to change it out. She currently says "welcome to open TX'

[@Painless360]

+Mike McCarty simply rename the sound file you want it to play with that name. Make sure it's the right format if you're trying to use a custom sound. Best of luck!

[@OneLousyShot]

Thats a DAMN SEXY voice..Nice Video

[@prOkrEAt]

so i see a bunch of *.txt files in your directory, mine has none either on the taranis or in the amber sound pack i downloaded. the amber sound pack only has files in the [SYSTEM] folder and not the additional files in the [en] folder. also where did you find the jpg and xlsx files? they werent in the zip file either? i downloaded the v2.1 for taranisplus location if that makes any difference. on a side note, i notice these sounds seem to be targeted towards planes, does anyone know of a sound pack targeted towards multicopters?

[@Painless360]

I've found the pack had everything I need for multi-rotor flying (flight modes etc) why not suggest the things you think are missing in the forum? Maybe they could be added to the next version. Don't forget that you can make your own sound files too..

[@prOkrEAt]

Painless360​ that's what I was mentioning in my first paragraph somewhat, files seemed to be missing in 2.1zip file. Do I need to DL the 2.0 version as well? Or another one no the taranisplus DL? And yes, recording my own soundpack seems like a fun side project!

[@Painless360]

Try downloading from www.rcgroups.com/forums/showthread.php?t=2151914 ;)

[@prOkrEAt]

Painless360 ah, thanks! one at opentx site was only 4.4mB, this was 15mB.

[@rankingbadboy]

Hi mate great video I just updated my radio to 2.2 and I don’t get any sound on the open TX screen the file is on the card all the other sounds work when moving switch but only the open TX screen can you help please. Thanks

[@Painless360]

If you watch any of my videos on upgrading to OpenTX 2.2 it'll explain how you also need to copy files to the SD card as well. The file that's played the start-up is called tada.wav. You need to make sure that that one is there, sometimes there a couple of options and you'll need to rename one of them to that file name to get it to play Best of luck

[@rankingbadboy]

Thanks for your reply i did have that TADA.WAV file but still didnot work, the 2.2.1 firmware it has been changed to HELLO.WAV file when i put this in it worked. Happy days and thanks great channel.

[@Painless360]

They are naughty changing the sound files like this - glad you got it sorted! :D

[@rankingbadboy]

cheers mate

[@boriquadfpv7677]

Can't seem to download the files it redirects me to godaddy.

[@Painless360]

You can find them on the OpenTX university sites.. Best of luck..

[@brummy12345]

Hi I've done the amber pack and I have two copy's of the tracks on the taranis the first lot have a dot then a dash in front of them but they don't work if I scroll past all of them I get the same list with out the dot and dash but they work how can I lose the first lot? Thanks

[@Painless360]

+Team British Knights You can plug the SD card into a computer (or connect to the Taranis over a USB connection) and select the files you don't want and delete them. I would slways make a copy of any directory you intend to change so you can always have a backup and can go back if needed. Best of luck.

[@brummy12345]

+Painless360 thanks for the fast reply I've connected to the pc and it only shows 1 copy but still 2 copy's in the taranis totally thrown me off now lol.

[@raylotier]

+Team British Knights I have this issue as well. Double files but one set has ._ in front of it and won't play a track when selected. Could they be a texts files???

[@brummy12345]

+Ray Lotier I still haven't worked out how to lose them I've looked every were and you can't delete them off the radio side

[@Painless360]

You can't delete them from the radio, you need to plug the SD card into the PC or connect to the radio using a USB cable. I found sorting the audio files in the directory by date helped me spot the 'old ones'. Make a copy of the complete directory contents before you delete anything for safety.

[@pabz06]

how do you change screen color?

[@Painless360]

Check out the playlist - we have a video that covers that exact question. Best of luck!

[@MrTMoore55]

And, someone could get rich upgrading firmware, installing play tracks ect. On folks radios!!! I like it but way above my head. HELPPP!!!!

[@Painless360]

Help?

[@matjaz3882]

I can't download these sound pack. It just tell me that the file is missing. Can you send me sound pack to my email? Leave a comment if you do that

[@Painless360]

Google found this - open-txu.org/home/v2-1-resources/ ;) Hope it helps.

[@matjaz3882]

Thank you It really helped me and now it is working just fine. Thanks

[@Painless360]

It's all out there, but things do move now and then. Places like the OpenTX university (as linked above) are gold mines..

[@LachlanPeknice]

links?

[@Painless360]

Google?

[@LachlanPeknice]

you said you would put links in the description...

[@Painless360]

open-txu.org/home/v2-1-resources/ :)

[@LachlanPeknice]

Legend, Thanks!